| name | glinet-slate7 |
| description | Comprehensive reference for the GL-iNet Slate 7 travel router (model GL-BE3600, Wi-Fi 7).
Covers hardware specs, 2.5G ports, touchscreen interface, full admin panel menu structure,
VPN client setup (WireGuard/OpenVPN; NordVPN, Mullvad, Surfshark, and 30+ providers),
WireGuard/OpenVPN server setup, AdGuard Home, Tor, Tailscale, DDNS, network modes
(Router/AP/Extender/WDS/Drop-in Gateway), SSH/CLI access with command reference,
factory reset, firmware update, and U-Boot bricked-device recovery. Also covers the
JSON-RPC admin API at /rpc (challenge/response auth, module/method discovery, reusable
bash helper), programmatic WireGuard server provisioning via the wg-server module
(add_peer, generate_peer, settings, leak verification, local-only Endpoint pattern),
and Linux client-side WG with overlay-VPN stacking — including the two leak modes
that appear when running Tailscale on top of a full-tunnel WG client (fwmark 0x80000
bypass and wg-quick catch-all shadowing the tailnet routes) plus the wg-quick
PostUp/PreDown ip-rule fixes. Applicable to most GL-iNet sdk4 firmware devices, not
only the Slate 7.
Use when a user specifically asks about the GL-iNet Slate 7 or GL-BE3600 — setup,
initial connection, admin panel access, VPN configuration, SSH, troubleshooting lost
admin access, device recovery, scripting the admin API, provisioning the built-in
WireGuard server without the UI, configuring a Linux WG client against the device,
or layering Tailscale/ZeroTier on top of that WG client. Do not trigger for generic
router questions not specific to GL-iNet Slate 7.
|
GL-iNet Slate 7 (GL-BE3600) Reference
Quick Reference
| Item | Value |
|---|
| Model | GL-BE3600 (Slate 7) |
| Admin panel URL | http://192.168.8.1 |
| Default LAN subnet | 192.168.8.0/24 |
| Default 2.4 GHz SSID | GL-BE3600-XXX (see bottom label) |
| Default 5 GHz SSID | GL-BE3600-XXX-5G (see bottom label) |
| Default Wi-Fi password | Printed on bottom label |
| Admin password | None — must be set on first boot |
| SSH username / port | root / 22 |
| SSH password | Same as admin password |
| U-Boot recovery IP | Computer: 192.168.1.2 → Router: 192.168.1.1 |
| Soft reset (Repair Mode) | Hold reset until touchscreen shows "Release to Repair Mode" |
| Factory reset | Hold reset until touchscreen shows "Release to Reset Mode" |
| Firmware downloads | https://dl.gl-inet.com/router/be3600/ |
| Official docs | https://docs.gl-inet.com/router/en/4/user_guide/gl-be3600/ |
What This Router Does
The Slate 7 is purpose-built for three scenarios:
- Privacy on the go — connects to hotel/cafe Wi-Fi or cellular data, then presents a clean, VPN-protected network to all your devices
- Portable gateway — acts as a full NAT router with firewall, DHCP, and DNS for any location
- Remote access hub — runs WireGuard or OpenVPN server so you can reach your home network securely from anywhere
Key Capabilities at a Glance
- Wi-Fi 7 (802.11be) with MLO — up to 3,570 Mbps theoretical, 2.4 GHz + 5 GHz simultaneously
- 2.5 Gbps WAN + 2.5 Gbps LAN Ethernet ports
- WireGuard client up to ~490 Mbps throughput; OpenVPN with DCO up to ~385 Mbps
- 30+ VPN provider integrations (NordVPN, Mullvad, Surfshark, PIA, and more)
- VPN Server (WireGuard + OpenVPN) with client config export
- AdGuard Home — DNS-level ad/tracker blocking, pre-installed (disabled when Tor is active)
- Tor — full-tunnel Tor routing for all connected devices (mutually exclusive with VPN clients, AdGuard Home, DNS encryption, and IPv6)
- Tailscale and ZeroTier overlay networking
- Multi-WAN failover — Ethernet + Repeater + Cellular with automatic switchover
- Drop-in Gateway mode — extend any existing router with VPN and ad blocking
- Touchscreen — swipe through status screens; toggle VPN and view Wi-Fi QR code without a browser; physical side toggle button assignable via System → Toggle Button Settings
- USB 3.0 — smartphone tethering, 4G/5G dongle, or network-attached storage
- LuCI (full OpenWrt UI) accessible via Admin Panel → System → Advanced Settings
Reference Files
| File | Contents |
|---|
| hardware-and-features.md | Hardware specs, ports, buttons, touchscreen screens, LED behavior, network modes comparison, feature limitations and known issues |
| web-ui-guide.md | Admin panel menu structure, every section explained, VPN setup flows (WireGuard client/server, OpenVPN client/server), AdGuard, DDNS, Tailscale, Tor, Multi-WAN |
| setup-and-management.md | Initial connection and first-time setup wizard, direct connection (no internet), SSH/CLI access and useful commands, troubleshooting, firmware update, U-Boot recovery |
| json-rpc-api.md | The /rpc JSON-RPC backend used by the admin panel — auth flow (challenge → SHA-256 crypt → sid), call envelope, module/method discovery via .so strings and gzipped Vue bundles in /www/views/, common modules table, reusable bash helper, error codes and pitfalls |
| wireguard-server-api.md | Programmatic provisioning of the built-in WireGuard server: wg-server module method reference, add_peer / generate_peer parameter shapes, end-to-end provisioning flow, server-side state inspection (UCI vs kernel vs RPC), local-only Endpoint pattern for LAN-side clients, leak verification |
| wg-client-stacked-tunnels.md | Read when: configuring a Linux WireGuard client against the GL-iNet server, debugging a full-tunnel WG client that won't reach the internet or tailnet, layering Tailscale/ZeroTier/another overlay on top of a WG client, or seeing symptoms like "tailscale ping --tsmp works but ICMP/SSH to a tailnet peer doesn't", "tailscale netcheck reports UDP blocked", or "large transfers stall while small probes succeed". Contents: wg-quick policy-routing internals (rules 5208/5209, table 51820, fwmark 0xca6c), MTU selection for stacked tunnels, the two leak modes specific to Tailscale-on-WG (fwmark 0x80000 bypass at 5210/5230/5250, and wg-quick's 5209 catch-all shadowing the tailnet routes) with copy-pasteable wg0.conf PostUp/PreDown fixes, leak-verification recipe, and a diagnostic command table covering , , the three modes, and journalctl interpretation. Generalizes to ZeroTier/Nebula/OpenVPN. |
Common Tasks
Get to the admin panel
Connect to the router by Ethernet (LAN port) or Wi-Fi (GL-BE3600-XXX), then open http://192.168.8.1.
Connect to a VPN provider
Admin Panel → VPN → WireGuard Client (or OpenVPN Client) → select provider or "Add Manually" → upload config → start. See web-ui-guide.md for provider-specific credential notes.
Enable ad blocking
Admin Panel → Applications → AdGuard Home → toggle on. Can also be toggled directly from the touchscreen.
Share Wi-Fi credentials via QR code
Swipe the touchscreen to the Wi-Fi screen — it shows the SSID, password, and a scannable QR code.
Reset to factory defaults
Hold the reset button until the touchscreen shows "Release to Reset Mode", then release. Or: Admin Panel → System → Reset Firmware → Delete All and Reboot.
Access CLI
ssh root@192.168.8.1 — password is the same as your admin panel password. See setup-and-management.md for useful commands.
Run a VPN server (WireGuard)
Admin Panel → VPN → WireGuard Server → Generate Configuration → Profiles tab → Add profile → export QR/config → Start server. Requires a public IP or DDNS hostname. Full flow in web-ui-guide.md.
Provision WireGuard server programmatically (no UI)
Auth to the /rpc API, then call wg-server.set_setting, wg-server.add_peer, wg-server.generate_peer, wg-server.start. End-to-end shell flow in wireguard-server-api.md. Underlying auth/envelope and reusable bash helper in json-rpc-api.md.
Script the admin panel
The admin UI is a Vue SPA over a JSON-RPC backend at http://192.168.8.1/rpc. Modules live in /usr/lib/oui-httpd/rpc/; method names and parameter shapes can be discovered from the gzipped Vue bundles in /www/views/. See json-rpc-api.md for the auth flow, request envelope, module/method discovery, and a reusable bash client.
Build a LAN-only WireGuard tunnel (no public IP / DDNS)
Set Endpoint = 192.168.8.1:<listen_port> in the client config and local_access: true on the server. The handshake stays on the LAN segment and the client gets full-tunnel egress through the router with no external port-forwarding. Verification (tcpdump leak check) and pitfalls in wireguard-server-api.md.
Layer Tailscale (or another overlay VPN) on top of a WG client tunnel
Naive stacking leaks two ways on Linux: Tailscale's fwmark 0x80000 bypass rules at priorities 5210/5230/5250 escape wg0, and wg-quick's catch-all at 5209 shadows Tailscale's tailnet routes in table 52. Both fixes are wg-quick PostUp/PreDown rule inserts (priorities 5200, 5205, 5206). Full explanation, ready-to-paste rules, MTU guidance for stacked tunnels, and diagnostic command table in wg-client-stacked-tunnels.md.
Router is unreachable at 192.168.8.1
Mode may have been switched to AP or WDS. Hold the reset button until the touchscreen shows "Release to Repair Mode", then release — this reverts to Router Mode. See setup-and-management.md.
Device bricked / firmware corrupted
Enter U-Boot recovery mode, set computer IP to 192.168.1.2, open http://192.168.1.1, flash firmware. Full procedure in setup-and-management.md.
Network Modes Summary
| Mode | NAT/DHCP | Admin at 192.168.8.1 | VPN/Features | Best For |
|---|
| Router (default) | Yes | Always | All enabled | Gateway, travel, primary router |
| Access Point | No | No — find IP from upstream | Limited | Wired uplink, extend coverage |
| Extender | No | Yes | Limited | Wireless range extension |
| WDS | No | No — find IP from upstream | Limited | Multi-router bridge |
| Drop-in Gateway | Transparent | Yes | VPN + AdGuard for entire upstream network | Augment existing router |
Full mode details and switching instructions: hardware-and-features.md
