Skip to main content Home Creators deanyou virtuoso-cli spectre-netlist-template
spectre-netlist-template Add stimulus and analysis templates to a Spectre netlist that has no excitation.
Use when: (1) Ocean/ADE-generated netlist has no testbench wrapper (no vsource,
no analysis statements), (2) you need to measure a specific figure of merit
(GBW, PM, PSRR, CMRR, noise, load regulation, offset, propagation delay, etc.),
(3) you are setting up standalone Spectre simulation from a bare subcircuit netlist.
Identifies circuit type from port names / device types, then inserts the matching
stimulus + analysis block from the canonical templates below.
Jump to install Skills Marketplace Discover and explore AI skills built by the community.
Install with Codex or Claude Copy this prompt, paste it into Codex, Claude, or another assistant, and let it review the skill page and install it for you.
Show prompt details A direct command skips the review prompt. Inspect the source before running it.
npx skills add https://github.com/deanyou/virtuoso-cli --skill spectre-netlist-templateThe command stays on one line. Scroll horizontally to inspect it before copying.
Prefer a local copy? Download the files currently available to SkillsMP.
Download Zip Downloading... More from this repository Maestro (ADE Assembler) session management and simulation. Use when: running simulations via Maestro, configuring tests/analyses/outputs, updating design variables, reading results.
Amplifier design copilot — topology selection, sizing via gm/Id lookup tables, PVT corner validation, and process-portable design. Use when designing amplifiers (OTA, opamp, comparator), selecting topology from specs, sizing transistors, or characterizing a new process node. Also triggers on keywords like amplifier, OTA, opamp, gain-bandwidth, CMRR, PSRR, slew rate.
Explore Virtuoso cellviews - list libraries, cells, instances, nets, layers, and hierarchy. Use when browsing a design, understanding circuit topology, or inspecting layout/schematic contents.
Related occupations SOC
Based on SOC occupation classification
name spectre-netlist-template description Add stimulus and analysis templates to a Spectre netlist that has no excitation.
Use when: (1) Ocean/ADE-generated netlist has no testbench wrapper (no vsource,
no analysis statements), (2) you need to measure a specific figure of merit
(GBW, PM, PSRR, CMRR, noise, load regulation, offset, propagation delay, etc.),
(3) you are setting up standalone Spectre simulation from a bare subcircuit netlist.
Identifies circuit type from port names / device types, then inserts the matching
stimulus + analysis block from the canonical templates below.
author Claude Code version 1.0.0 date "2026-04-19T00:00:00.000Z" source /opt/cadence/IC231/doc/spectremod/Chap1.html (vsource/isource/port syntax) /opt/cadence/IC231/doc/spectreref/chap3.html (analysis statements) argument-hint ["circuit type","e.g. \"OTA\" or \"LDO\" or \"bandgap\" or \"VCO\""] allowed-tools Bash(python *) Bash(spectre *) Read Write
Spectre Netlist Template — Stimulus & Analysis
All syntax verified against Cadence IC231 / Spectre 20.1 reference documentation.
Step 0 — Read and Classify the Netlist
Before adding any template:
Read the .scs file; locate the top-level subcircuit declaration:
subckt CELL_NAME port1 port2 ...
Identify circuit type from the port list + device inventory:
Circuit type Identifying signals Dominant devices OTA / Opamp VIN+ / VIN- / VOUT / VOUTP / VOUTNMOSFETs, tail current source Fully-differential OTA Two differential outputs (VOUTP VOUTN) MOSFETs + CMFB LDO / Regulator VIN / VOUT / FB / ENpass FET, error amp Comparator VIN+ / VIN- / VOUT / CLK (if clocked)strong-arm / regenerative latch Bandgap reference VREF / VBG / VBGR / IREFBJTs, poly resistors Current mirror / bias IBIAS / IOUT / VBIASstacked MOSFETs Active filter VIN / VOUTOTA + C (no large devices) Ring oscillator / VCO VCTRL / VOUT / OUT + odd-number inverter chaininverters LNA / RF amp RF_IN / RF_OUT / port elementsLC matching, RF MOSFETs
If unsure, inspect instance types: nmos4 pmos4 → analog amplifier; mostly inverters →
oscillator/digital; bjt /
bsim3v3
Syntax Reference (from IC231 documentation)
vsource parameters // DC bias supply
VVDD (VDD 0) vsource dc=<V>
VVSS (VSS 0) vsource dc=<-V> ; for negative rail
// AC small-signal (MUST use mag=, NOT ac=; ac= is SPICE-only → SFE-30)
VIN (VIN 0) vsource dc=<bias_V> mag=1 ; single-ended AC input
VIP (VIP 0) vsource dc=<bias_V> mag=0.5 ; differential AC input (+)
VIN_ (VIN_ 0) vsource dc=<bias_V> mag=-0.5 ; differential AC input (-)
// PSRR supply perturbation
VVDD_psrr (VDD 0) vsource dc=<V> mag=1 ; inject on supply
// Pulse (for tran)
VPULSE (NODE 0) vsource type=pulse val0=<V0> val1=<V1> \
period=<T> rise=<tr> fall=<tf> width=<pw> delay=<td>
// Sine (for tran / distortion)
VSINE (NODE 0) vsource type=sine sinedc=<bias> ampl=<A> freq=<Hz>
// PWL (arbitrary waveform)
VPWL (NODE 0) vsource type=pwl wave=[<t0> <v0> <t1> <v1> ...]
isource parameters // DC current bias / load
ILOAD (VDD VOUT) isource dc=<A> ; load current sink (+ flows from VDD into VOUT)
IREF (VREF 0) isource dc=<A> ; reference current
// AC perturbation
IIN (VIN 0) isource dc=0 mag=1 ; AC current input
// Pulse (load step for LDO)
ISTEP (VOUT 0) isource type=pulse val0=<I0> val1=<I1> \
period=<T> rise=<tr> fall=<tf> width=<pw>
port element (S-parameter / RF) // Port for sp analysis — resistance sets reference impedance
PORT1 (RF_IN 0) port r=50 num=1
PORT2 (RF_OUT 0) port r=50 num=2
iprobe (current probe — zero-voltage series sense) IPROBE0 (VOUT_INT VOUT) iprobe ; zero-voltage drop, senses current at VOUT
Analysis Statement Syntax (from IC231 Spectre Reference Manual) // ─── DC operating point ───
dcop dc oppoint=rawfile save=allpub
// ─── DC sweep (parameter) ───
dcswp dc param=<param_name> start=<val> stop=<val> step=<val> \
oppoint=rawfile save=allpub
// ─── DC sweep (voltage/current source) ───
dcswp dc dev=<vsource_name> start=<V> stop=<V> lin=<N> oppoint=rawfile
// ─── AC frequency sweep ───
ac1 ac start=1 stop=100Meg dec=50
// ─── Transient ───
tran1 tran stop=<time> maxstep=<step> errpreset=moderate
// ─── Noise ───
// outputport: element name (NOT node name) → use 1TΩ parallel resistor
// inputport: driving vsource element name
noise_an noise start=1 stop=100Meg dec=50 \
outputport=<Rprobe_name> inputport=<Vsrc_name>
// ─── Stability (loop gain, PM) ───
// probe: iprobe element OR element:p/n for current measurement point
stb1 stb start=1 stop=100Meg dec=50 probe=<iprobe_or_element>
// ─── Transfer function ───
xf1 xf start=1 stop=100Meg dec=50 probe=<output_node>
// ─── S-parameters ───
sp1 sp start=100Meg stop=10G dec=20 ports=[PORT1 PORT2]
// ─── Periodic Steady State (oscillator / VCO) ───
pss1 pss fund=<Hz> harms=20 errpreset=moderate maxacfreq=10G
// ─── simulatorOptions global ───
simulatorOptions options temp=27 tnom=27 scale=1e-6 \
audioverilog=no gmin=1e-12 rforce=1 noisefloor=1e-11 \
save=allpub dc_pivot_check=yes pivtol=1e-13 vabstol=1e-6 \
iabstol=1e-12 compatible=spice2
Circuit-Type Templates
1. OTA / Single-Ended Opamp Ports expected : VDD VSS VIN+ VIN- VOUT (± VBIAS, VCMFB)
// ── Supplies ──────────────────────────────────────────────
VVDD (VDD 0) vsource dc=VDD
VVSS (VSS 0) vsource dc=VSS ; 0 if single-supply
VCMFB (VCMFB 0) vsource dc=VCM ; if CMFB input exposed
// ── Common-mode bias ──────────────────────────────────────
VICM (VCM_NODE 0) vsource dc=VCM ; adjust to mid-rail
// ── Differential AC input: ±mag/2 for 1V differential ─────
VIP (VIN_P 0) vsource dc=VCM mag=0.5 ; positive half
VIN_ (VIN_N 0) vsource dc=VCM mag=-0.5 ; negative half
// ── Load ──────────────────────────────────────────────────
CL (VOUT 0) capacitor c=CL ; load cap (parameter)
Rload (VOUT 0) resistor r=Rload ; if resistive load
// ── Noise oprobe (parallel, NOT series) ───────────────────
Rprobe (VOUT 0) resistor r=1T ; 1TΩ parallel sense element
// ── Analyses ──────────────────────────────────────────────
parameters VDD=1.8 VSS=0 VCM=0.9 CL=1p Rload=1T
dcop dc oppoint=rawfile save=allpub
ac1 ac start=1 stop=1G dec=50
stb1 stb start=1 stop=1G dec=50 probe=Rprobe
noise1 noise start=1 stop=1G dec=50 outputport=Rprobe inputport=VIP
Measurements from results :
GBW: AC magnitude crosses 0 dB → read frequency
Phase margin: phase at GBW frequency
Loop gain (stb): loopGain signal in PSF; PM from phase of loop gain
Input-referred noise: noise analysis → in (input-referred) signal
2. Fully-Differential OTA Ports expected : VDD VSS VIN+ VIN- VOUTP VOUTN VCMFB
VVDD (VDD 0) vsource dc=VDD
VVSS (VSS 0) vsource dc=VSS
VCMFB (VCMFB 0) vsource dc=VCM ; ideal CMFB for open-loop test
VIP (VIN_P 0) vsource dc=VCM mag=0.5
VIN_ (VIN_N 0) vsource dc=VCM mag=-0.5
// Differential output load
CLp (VOUTP 0) capacitor c=CL
CLn (VOUTN 0) capacitor c=CL
Rprobep (VOUTP 0) resistor r=1T
Rproben (VOUTN 0) resistor r=1T
parameters VDD=1.8 VSS=0 VCM=0.9 CL=1p
dcop dc oppoint=rawfile save=allpub
ac1 ac start=1 stop=1G dec=50
stb1 stb start=1 stop=1G dec=50 probe=Rprobep
noise1 noise start=1 stop=1G dec=50 outputport=Rprobep inputport=VIP
3. LDO / Voltage Regulator Ports expected : VIN VOUT FB GND (± EN, VBIAS)
VVIN (VIN 0) vsource dc=VIN
VCMFB (FB 0) vsource dc=VFB ; if FB is a direct pin (no resistor divider)
// or: external resistor divider R1/R2 from VOUT to FB to GND
// Load: nominal + step
ILOAD (VOUT GND_NODE) isource dc=ILOAD_DC
ISTEP (VOUT GND_NODE) isource type=pulse \
val0=ILOAD_DC val1=ILOAD_MAX delay=5u period=30u rise=100n fall=100n width=10u
// Loop-break iprobe for Bode plot
Ibrk (VOUT_SENSE VOUT) iprobe ; insert in feedback path
// Noise probe
Rprobe (VOUT GND_NODE) resistor r=1T
parameters VIN=3.3 VREF=1.2 VFB=VREF ILOAD_DC=1m ILOAD_MAX=100m
dcop dc oppoint=rawfile save=allpub
// Line regulation
linereg dc dev=VVIN start=2 stop=5 lin=31
// Load regulation
loadreg dc dev=ILOAD start=0 stop=ILOAD_MAX lin=51
stb1 stb start=1 stop=100Meg dec=50 probe=Ibrk
tran1 tran stop=100u maxstep=10n errpreset=moderate ; load step
noise1 noise start=1 stop=10Meg dec=50 outputport=Rprobe inputport=VVIN
4. Comparator (static / strong-arm) Ports expected : VDD VSS VIN+ VIN- VOUT CLK (clocked) or VIN+ VIN- VOUT (static)
VVDD (VDD 0) vsource dc=VDD
VVSS (VSS 0) vsource dc=VSS
// Static comparator: ramp one input, hold the other at VCM
VPOS (VIN_P 0) vsource type=pwl \
wave=[0 VCM 1n VCM 101n VSTOP] ; slow ramp to find threshold
VNEG (VIN_N 0) vsource dc=VCM
// Clocked comparator: differential pulse, external CLK
VCLK (CLK 0) vsource type=pulse val0=0 val1=VDD \
period=TCLK rise=100p fall=100p width=TCLK_H delay=0
VDIFF (VIN_P VIN_N) vsource dc=0 type=pulse \
val0=-VDIFF_NEG val1=VDIFF_POS rise=1p fall=1p width=TCLK delay=TCLK_H
parameters VDD=1.8 VSS=0 VCM=0.9 VSTOP=VDD TCLK=2n TCLK_H=1n \
VDIFF_NEG=10m VDIFF_POS=10m
dcop dc oppoint=rawfile save=allpub
tran1 tran stop=10n maxstep=10p errpreset=moderate
// Hysteresis (static comparator)
hysteresis dc dev=VPOS start=0 stop=VDD lin=101 hysteresis=yes
Propagation delay: tran → time from CLK edge to VOUT 50% crossing
Offset: DC sweep → VOUT switches midpoint vs VCM
Hysteresis: DC hysteresis sweep → forward/reverse threshold difference
5. Bandgap Reference Ports expected : VDD GND VREF (± IREF, VSTART, VTRIM)
VVDD (VDD 0) vsource dc=VDD
// Supply ramp for startup check
VRAMP (VDD_RAMP 0) vsource type=pwl \
wave=[0 0 100n 0 1u VDD_MAX] ; slow ramp on supply rail
// Noise probe
Rprobe (VREF 0) resistor r=1T
parameters VDD=3.3 VDD_MAX=3.6 TEMP_START=-40 TEMP_STOP=125
dcop dc oppoint=rawfile save=allpub
// Line regulation: VREF vs VDD
linereg dc dev=VVDD start=1.5 stop=VDD_MAX lin=51
// Temperature coefficient: requires corner sweep (use parametric or Monte Carlo)
// tempco dc param=temp start=TEMP_START stop=TEMP_STOP lin=166
// PSRR
VVDD_psrr (VDD 0) vsource dc=VDD mag=1 ; AC inject on supply
psrr ac start=1 stop=100Meg dec=50
noise1 noise start=1 stop=10Meg dec=50 outputport=Rprobe inputport=VVDD_psrr
tran1 tran stop=10u maxstep=10n errpreset=moderate ; startup check
TC [ppm/°C]: (VREF_max - VREF_min) / (VREF_nom * ΔT) × 1e6
PSRR: AC analysis → 20log(VREF_out / VVDD_in)
Line regulation: DC sweep → dVREF/dVDD [mV/V]
6. Current Mirror / Bias Generator Ports expected : VDD VSS IBIAS_IN IBIAS_OUT (± VBIAS, VCASC)
VVDD (VDD 0) vsource dc=VDD
VVSS (VSS 0) vsource dc=VSS
// Reference current source
IREF (VDD IBIAS_IN) isource dc=IREF_DC
// Output compliance sweep
VCMP (IBIAS_OUT 0) vsource dc=VSTART ; sweeps to check compliance
// Small-signal: output impedance
VTEST (IBIAS_OUT_AC IBIAS_OUT) vsource dc=0 mag=1 ; inject test voltage
parameters VDD=1.8 VSS=0 IREF_DC=10u VSTART=0.1
dcop dc oppoint=rawfile save=allpub
// Mirror ratio check
compliance dc dev=VCMP start=0.1 stop=VDD lin=51
// Output impedance via AC
ac_rout ac start=1 stop=100Meg dec=50 ; measure ITEST/VTEST at IBIAS_OUT
7. Active Filter (OTA-C / Gm-C / Sallen-Key) Ports expected : VDD VSS VIN VOUT
VVDD (VDD 0) vsource dc=VDD
VVSS (VSS 0) vsource dc=VSS
// AC input (singled-ended)
VIN_ac (VIN 0) vsource dc=VCM mag=1
// Step input for tran
VSTEP (VIN 0) vsource type=pulse val0=0 val1=VSTEP_AMP \
delay=100n rise=1p fall=1p width=10u period=20u
// Output sense
Rprobe (VOUT 0) resistor r=1T
parameters VDD=1.8 VSS=0 VCM=0.9 VSTEP_AMP=100m
dcop dc oppoint=rawfile save=allpub
ac1 ac start=1 stop=1G dec=100 ; frequency response (fine resolution)
tran1 tran stop=50u maxstep=1n errpreset=moderate
noise1 noise start=1 stop=1G dec=50 outputport=Rprobe inputport=VIN_ac
8. Ring Oscillator / VCO Ports expected : VDD VSS OUT (± VCTRL for VCO)
VVDD (VDD 0) vsource dc=VDD
VVSS (VSS 0) vsource dc=VSS
VCTRL (VCTRL 0) vsource dc=VCTRL_NOM ; VCO control voltage
parameters VDD=1.8 VSS=0 VCTRL_NOM=0.9 Tosc=2n
// Tran: measure oscillation period
tran1 tran stop=100n maxstep=1p errpreset=moderate skipdc=no
// PSS: periodic steady state → spectral purity
pss1 pss fund=1/Tosc harms=20 errpreset=moderate maxacfreq=100G
// VCO gain (KVCO): DC sweep of VCTRL
vco_kvco dc dev=VCTRL start=0.2 stop=VDD-0.2 lin=51
Measurements from tran : zero-crossings of OUT → period → frequency
PSS : phase noise, KVCO from pss/pac
9. LNA / RF Amplifier (S-parameters) Ports expected : VDD VSS RF_IN RF_OUT (± VBIAS, IBIAS)
VVDD (VDD 0) vsource dc=VDD
VVSS (VSS 0) vsource dc=VSS
VBIAS (VBIAS 0) vsource dc=VBIAS_NOM
// S-parameter ports (50Ω reference)
PORT1 (RF_IN 0) port r=50 num=1
PORT2 (RF_OUT 0) port r=50 num=2
parameters VDD=1.2 VSS=0 VBIAS_NOM=0.6
dcop dc oppoint=rawfile save=allpub
// S-parameter sweep
sp1 sp start=100Meg stop=10G dec=20 ports=[PORT1 PORT2]
// Noise figure (input-referred noise)
noise1 noise start=100Meg stop=10G dec=20 \
outputport=PORT2 inputport=PORT1
// Large-signal tran (1-dB compression point — vary ampl)
tran1 tran stop=50n maxstep=1p errpreset=moderate
S11 (return loss), S21 (gain), S12 (isolation), S22 (output match) from sp analysis
Noise figure from noise analysis in signal
IIP3: two-tone tran → FFT
Workflow
Read netlist → identify subcircuit name + port listMatch circuit type from table in Step 0Choose template from the matching section aboveInstantiate the subcircuit at top level:
simulator lang=spectre
global 0
include "input.scs" ; ADE-generated subcircuit
parameters VDD=1.8 ...
// ── DUT instantiation ──
XDUT (VDD VSS VIN_P VIN_N VOUT) CELL_NAME
// ── Stimulus from template ──
...
// ── Analyses from template ──
...
Adjust node names to match actual DUT port orderVerify mag=1 on all AC excitation sources (not ac=1)Run : spectre input.scs -raw psf -format psfascii
Automated Script: inject_stimulus.py For batch or scripted use, the skill ships a Python helper that auto-detects circuit
type and generates a complete testbench file — no Virtuoso running required.
python ${CLAUDE_SKILL_DIR} /scripts/inject_stimulus.py bandgap.scs
python ${CLAUDE_SKILL_DIR} /scripts/inject_stimulus.py amp.scs --type ota
python ${CLAUDE_SKILL_DIR} /scripts/inject_stimulus.py amp.scs -o amp_testbench.scs
python ${CLAUDE_SKILL_DIR} /scripts/inject_stimulus.py chip.scs --cell Bandgap
python ${CLAUDE_SKILL_DIR} /scripts/inject_stimulus.py chip.scs --list
spectre bandgap_tb.scs -raw psf -format psfascii
The script requires no third-party libraries (stdlib only).
After generation, review and adjust parameter values (VDD, CL, temperatures, etc.)
to match the target PDK and operating conditions.
Common mistakes : see /spectre-netlist-gotchas for SFE-30 (ac=1 → mag=1), SFE-1997, oprobe wiring, global 0, port order, and noise parameter errors.
