Run any Skill in Manus with one click

sensor-drivers

Stars2

Forks0

UpdatedJanuary 18, 2026 at 14:02

Guidance for embedded sensor drivers used in the payload. Use when working with BMP390, ENS160, LSM6DSOX, LIS3MDL, GPS, IMU, barometer, or any sensor integration.

Installation

Install with Codex or Claude Copy this prompt, paste it into Codex, Claude, or another assistant, and let it review the skill page and install it for you.

Run Skill in Manus

Source

njfdev

njfdev/ncssm_hpr_2025_payload

View GitHub Repository View Creator Repositories

Download

Run Skill in Manus

Related occupationsSOC

Based on SOC occupation classification

Software DevelopersComputer and Mathematical Occupations·SOC 15-1252

SKILL.md

readonly

Payload Sensor Drivers

Hardware Configuration

Sensor	Type	Bus	SDA	SCL	I2C Address
BMP390	Barometer	I2C1	GP2	GP3	0x77 (SDO high)
ENS160	Gas/Air Quality	I2C1	GP2	GP3	0x53 (ADDR high)
LSM6DSOX	6-axis IMU	I2C0	GP28	GP29	0x6A (SA0 low)
LIS3MDL	Magnetometer	I2C0	GP28	GP29	0x1C (SA1 low)

CRITICAL: Use the SCAN command to verify which I2C bus sensors are actually on. The ENS160 was initially assumed to be on I2C0 but scanning revealed it was on I2C1 with BMP390.

BMP390 - Barometric Pressure Sensor

Datasheet: Bosch BMP390

Specifications

Pressure range: 300-1250 hPa
Relative accuracy: ±3 Pa (~0.25m altitude)
Absolute accuracy: ±0.40 hPa
Temperature: -40 to +85°C (±0.5°C accuracy)
Power: 3.2 µA @ 1Hz

I2C Address

0x76: SDO pin connected to GND
0x77: SDO pin connected to VDDIO (3.3V) ← Our configuration

Key Registers

Register	Address	Description
CHIP_ID	0x00	Chip ID (reads 0x60)
ERR_REG	0x02	Error register
STATUS	0x03	Sensor status
DATA_0-5	0x04-0x09	Pressure and temperature data
INT_STATUS	0x11	Interrupt status
PWR_CTRL	0x1B	Power control (enable press/temp)
OSR	0x1C	Oversampling settings
ODR	0x1D	Output data rate
CONFIG	0x1F	IIR filter config
CALIB_DATA	0x31-0x45	Calibration coefficients (21 bytes)
CMD	0x7E	Command register

Power Modes

Sleep: No measurements (default after reset)
Forced: Single measurement, then sleep
Normal: Continuous measurements with standby

Initialization Sequence

const BMP390_ADDR: u8 = 0x77;
const CHIP_ID: u8 = 0x00;
const PWR_CTRL: u8 = 0x1B;
const OSR: u8 = 0x1C;
const ODR: u8 = 0x1D;

// 1. Read and verify chip ID (should be 0x60)
let mut id = [0u8];
i2c.write_read(BMP390_ADDR, &[CHIP_ID], &mut id).await?;
assert_eq!(id[0], 0x60);

// 2. Read calibration data (21 bytes from 0x31)
let mut calib = [0u8; 21];
i2c.write_read(BMP390_ADDR, &[0x31], &mut calib).await?;

// 3. Configure oversampling (x8 pressure, x1 temp)
i2c.write(BMP390_ADDR, &[OSR, 0b00000011]).await?;

// 4. Configure ODR (50 Hz = 0x02)
i2c.write(BMP390_ADDR, &[ODR, 0x02]).await?;

// 5. Enable pressure and temp, normal mode
// PWR_CTRL: press_en=1, temp_en=1, mode=normal(11)
i2c.write(BMP390_ADDR, &[PWR_CTRL, 0b00110011]).await?;

Reading Data

const DATA_0: u8 = 0x04;

// Read 6 bytes: pressure (3) + temperature (3)
let mut data = [0u8; 6];
i2c.write_read(BMP390_ADDR, &[DATA_0], &mut data).await?;

// Pressure: 24-bit unsigned (XLSB, LSB, MSB)
let press_raw = (data[2] as u32) << 16 | (data[1] as u32) << 8 | data[0] as u32;

// Temperature: 24-bit unsigned (XLSB, LSB, MSB)
let temp_raw = (data[5] as u32) << 16 | (data[4] as u32) << 8 | data[3] as u32;

// Apply compensation algorithm from datasheet using calibration data

ENS160 - Digital Metal-Oxide Multi-Gas Sensor

Datasheet: ScioSense ENS160

Specifications

Air Quality Index (AQI): 1-5 scale
Total VOC (TVOC): 0-65000 ppb
Equivalent CO2 (eCO2): 400-65000 ppm
Operating temperature: -40 to +85°C
Warm-up time: 3 minutes (initial), then 1 second between readings

I2C Address

0x52: ADDR pin connected to GND
0x53: ADDR pin connected to VDDIO ← Our configuration

Note: The ENS160 also supports SPI mode. When using I2C, the CS pin must be held HIGH.

Key Registers

Register	Address	Description
PART_ID	0x00	Part ID (reads 0x0160, 2 bytes LE)
OPMODE	0x10	Operating mode
CONFIG	0x11	Configuration
COMMAND	0x12	Command register
TEMP_IN	0x13	Temperature compensation input (2 bytes)
RH_IN	0x15	Humidity compensation input (2 bytes)
DEVICE_STATUS	0x20	Device status
DATA_AQI	0x21	Air Quality Index (1 byte)
DATA_TVOC	0x22	TVOC in ppb (2 bytes LE)
DATA_ECO2	0x24	eCO2 in ppm (2 bytes LE)

Operating Modes

0x00: Deep sleep (lowest power)
0x01: Idle (ready for commands)
0x02: Standard mode (1 second measurement interval) ← Use this

Status Register (0x20)

[3:2] VALIDITY: Data validity
      00 = Normal operation
      01 = Warm-up phase (data not ready)
      10 = Initial start-up phase
      11 = Invalid output
[1] NEWDAT: New data available
[0] NEWGPR: New GPR data available

Initialization Sequence

const ENS160_ADDR: u8 = 0x53;
const PART_ID: u8 = 0x00;
const OPMODE: u8 = 0x10;
const COMMAND: u8 = 0x12;

// 1. Read and verify part ID (should be 0x0160)
let mut id_buf = [0u8; 2];
i2c.write_read(ENS160_ADDR, &[PART_ID], &mut id_buf).await?;
let part_id = u16::from_le_bytes(id_buf);
assert_eq!(part_id, 0x0160);

// 2. Set to idle mode (required before configuration)
i2c.write(ENS160_ADDR, &[OPMODE, 0x01]).await?;
Timer::after_millis(10).await;

// 3. Clear GPR registers (command 0xCC)
i2c.write(ENS160_ADDR, &[COMMAND, 0xCC]).await?;
Timer::after_millis(10).await;

// 4. Set to standard operating mode
i2c.write(ENS160_ADDR, &[OPMODE, 0x02]).await?;
Timer::after_millis(50).await;

Reading Data

const DEVICE_STATUS: u8 = 0x20;
const DATA_AQI: u8 = 0x21;
const DATA_TVOC: u8 = 0x22;
const DATA_ECO2: u8 = 0x24;

// Check status first
let mut status = [0u8];
i2c.write_read(ENS160_ADDR, &[DEVICE_STATUS], &mut status).await?;

// Check validity bits [3:2]
let validity = (status[0] & 0x0C) >> 2;
if validity > 1 {
    // 0 = normal, 1 = warm-up, 2+ = not ready
    return Ok(()); // Skip reading, keep previous values
}

// Read AQI (1 byte)
let mut aqi_buf = [0u8];
i2c.write_read(ENS160_ADDR, &[DATA_AQI], &mut aqi_buf).await?;
let aqi = aqi_buf[0]; // 1-5 scale

// Read TVOC (2 bytes, little-endian)
let mut tvoc_buf = [0u8; 2];
i2c.write_read(ENS160_ADDR, &[DATA_TVOC], &mut tvoc_buf).await?;
let tvoc_ppb = u16::from_le_bytes(tvoc_buf);

// Read eCO2 (2 bytes, little-endian)
let mut eco2_buf = [0u8; 2];
i2c.write_read(ENS160_ADDR, &[DATA_ECO2], &mut eco2_buf).await?;
let eco2_ppm = u16::from_le_bytes(eco2_buf);

Temperature/Humidity Compensation

const TEMP_IN: u8 = 0x13;
const RH_IN: u8 = 0x15;

// Temperature in centidegrees (25.5°C = 2550)
// ENS160 expects: (T + 273.15) * 64
let temp_encoded = ((temp_centideg as u32 + 27315) * 64 / 100) as u16;
let bytes = temp_encoded.to_le_bytes();
i2c.write(ENS160_ADDR, &[TEMP_IN, bytes[0], bytes[1]]).await?;

// Humidity in percent * 100 (50.5% = 5050)
// ENS160 expects: RH * 512 / 100
let rh_encoded = (rh_centipercent as u32 * 512 / 10000) as u16;
let bytes = rh_encoded.to_le_bytes();
i2c.write(ENS160_ADDR, &[RH_IN, bytes[0], bytes[1]]).await?;

AQI Interpretation

Value	Air Quality
1	Excellent
2	Good
3	Moderate
4	Poor
5	Unhealthy

Important Notes

Warm-up time: ENS160 needs 3+ minutes to provide valid readings after power-on
Read rate: Internal update rate is 1Hz in standard mode, so reading faster is pointless
Temperature compensation: Feed in ambient temperature for more accurate TVOC/eCO2
CS pin: Must be held HIGH for I2C mode (if using breakout board with SPI option)

LSM6DSOX - 6-Axis IMU (Accelerometer + Gyroscope)

Datasheet: ST LSM6DSOX

Specifications

Accelerometer: ±2/±4/±8/±16 g
Gyroscope: ±125/±250/±500/±1000/±2000 dps
ODR: up to 6.66 kHz
Power: 0.55 mA in high-performance mode

I2C Address

0x6A: SA0/SDO pin connected to GND ← Our configuration
0x6B: SA0/SDO pin connected to VDDIO

Key Registers

Register	Address	Description
FUNC_CFG_ACCESS	0x01	Embedded functions config
WHO_AM_I	0x0F	Device ID (reads 0x6C)
CTRL1_XL	0x10	Accelerometer control
CTRL2_G	0x11	Gyroscope control
CTRL3_C	0x12	Control register 3
CTRL6_C	0x15	Accelerometer power mode
CTRL7_G	0x16	Gyroscope power mode
STATUS_REG	0x1E	Data ready status
OUTX_L_G	0x22	Gyro X low byte
OUTX_H_G	0x23	Gyro X high byte
OUTY_L_G	0x24	Gyro Y low byte
OUTY_H_G	0x25	Gyro Y high byte
OUTZ_L_G	0x26	Gyro Z low byte
OUTZ_H_G	0x27	Gyro Z high byte
OUTX_L_A	0x28	Accel X low byte
OUTX_H_A	0x29	Accel X high byte
OUTY_L_A	0x2A	Accel Y low byte
OUTY_H_A	0x2B	Accel Y high byte
OUTZ_L_A	0x2C	Accel Z low byte
OUTZ_H_A	0x2D	Accel Z high byte

CTRL1_XL (Accelerometer Control)

[7:4] ODR_XL: Output data rate
      0000 = Power-down
      0001 = 12.5 Hz
      0010 = 26 Hz
      0011 = 52 Hz
      0100 = 104 Hz
      0101 = 208 Hz
      0110 = 416 Hz
      0111 = 833 Hz
      1000 = 1.66 kHz
      1001 = 3.33 kHz
      1010 = 6.66 kHz

[3:2] FS_XL: Full-scale selection
      00 = ±2 g
      01 = ±16 g
      10 = ±4 g
      11 = ±8 g

[1] LPF2_XL_EN: Low-pass filter enable
[0] (unused)

CTRL2_G (Gyroscope Control)

[7:4] ODR_G: Output data rate (same as accelerometer)

[3:2] FS_G: Full-scale selection
      00 = ±250 dps
      01 = ±500 dps
      10 = ±1000 dps
      11 = ±2000 dps

[1] FS_125: 125 dps full-scale (overrides FS_G if set)
[0] (unused)

Initialization Sequence

const LSM6DSOX_ADDR: u8 = 0x6A;
const WHO_AM_I: u8 = 0x0F;
const CTRL1_XL: u8 = 0x10;
const CTRL2_G: u8 = 0x11;
const CTRL3_C: u8 = 0x12;

// 1. Read and verify WHO_AM_I (should be 0x6C)
let mut who = [0u8];
i2c.write_read(LSM6DSOX_ADDR, &[WHO_AM_I], &mut who).await?;
assert_eq!(who[0], 0x6C);

// 2. Software reset
i2c.write(LSM6DSOX_ADDR, &[CTRL3_C, 0x01]).await?;
Timer::after_millis(10).await;

// 3. Configure accelerometer: 104 Hz, ±16g
// ODR=0100, FS=01 (±16g) -> 0b0100_0100 = 0x44
i2c.write(LSM6DSOX_ADDR, &[CTRL1_XL, 0x44]).await?;

// 4. Configure gyroscope: 104 Hz, ±2000 dps
// ODR=0100, FS=11 (±2000 dps) -> 0b0100_1100 = 0x4C
i2c.write(LSM6DSOX_ADDR, &[CTRL2_G, 0x4C]).await?;

Reading Data

const OUTX_L_G: u8 = 0x22;

// Read 12 bytes: gyro (6) + accel (6)
let mut data = [0u8; 12];
i2c.write_read(LSM6DSOX_ADDR, &[OUTX_L_G], &mut data).await?;

// Gyroscope (signed 16-bit, dps)
let gx = i16::from_le_bytes([data[0], data[1]]);
let gy = i16::from_le_bytes([data[2], data[3]]);
let gz = i16::from_le_bytes([data[4], data[5]]);

// Accelerometer (signed 16-bit, g)
let ax = i16::from_le_bytes([data[6], data[7]]);
let ay = i16::from_le_bytes([data[8], data[9]]);
let az = i16::from_le_bytes([data[10], data[11]]);

// Convert to physical units
// For ±16g: sensitivity = 0.488 mg/LSB
// For ±2000 dps: sensitivity = 70 mdps/LSB

LIS3MDL - 3-Axis Magnetometer

Datasheet: ST LIS3MDL

Specifications

Range: ±4/±8/±12/±16 gauss
ODR: up to 1000 Hz (ultra-high performance)
Power: 270 µA @ 80 Hz

I2C Address

0x1C: SA1/SDO pin connected to GND ← Our configuration
0x1E: SA1/SDO pin connected to VDDIO

Key Registers

Register	Address	Description
WHO_AM_I	0x0F	Device ID (reads 0x3D)
CTRL_REG1	0x20	Control register 1 (ODR, mode)
CTRL_REG2	0x21	Control register 2 (full-scale)
CTRL_REG3	0x22	Control register 3 (power mode)
CTRL_REG4	0x23	Control register 4 (Z-axis mode)
CTRL_REG5	0x24	Control register 5 (block update)
STATUS_REG	0x27	Data status
OUT_X_L	0x28	X output low byte
OUT_X_H	0x29	X output high byte
OUT_Y_L	0x2A	Y output low byte
OUT_Y_H	0x2B	Y output high byte
OUT_Z_L	0x2C	Z output low byte
OUT_Z_H	0x2D	Z output high byte
TEMP_OUT_L	0x2E	Temperature low byte
TEMP_OUT_H	0x2F	Temperature high byte

CTRL_REG1 (ODR and XY Performance)

[7] TEMP_EN: Temperature sensor enable
[6:5] OM: X/Y-axis operative mode
      00 = Low-power
      01 = Medium-performance
      10 = High-performance
      11 = Ultra-high performance

[4:2] DO: Output data rate
      000 = 0.625 Hz
      001 = 1.25 Hz
      010 = 2.5 Hz
      011 = 5 Hz
      100 = 10 Hz
      101 = 20 Hz
      110 = 40 Hz
      111 = 80 Hz

[1] FAST_ODR: Enable rates >80 Hz
[0] ST: Self-test enable

CTRL_REG2 (Full-Scale Selection)

[6:5] FS: Full-scale configuration
      00 = ±4 gauss
      01 = ±8 gauss
      10 = ±12 gauss
      11 = ±16 gauss

CTRL_REG3 (Operating Mode)

[1:0] MD: Operating mode
      00 = Continuous-conversion
      01 = Single-conversion
      10 = Power-down (default)
      11 = Power-down

Initialization Sequence

const LIS3MDL_ADDR: u8 = 0x1C;
const WHO_AM_I: u8 = 0x0F;
const CTRL_REG1: u8 = 0x20;
const CTRL_REG2: u8 = 0x21;
const CTRL_REG3: u8 = 0x22;
const CTRL_REG4: u8 = 0x23;

// 1. Read and verify WHO_AM_I (should be 0x3D)
let mut who = [0u8];
i2c.write_read(LIS3MDL_ADDR, &[WHO_AM_I], &mut who).await?;
assert_eq!(who[0], 0x3D);

// 2. Configure CTRL_REG1: temp enable, ultra-high perf XY, 80 Hz
// TEMP_EN=1, OM=11, DO=111 -> 0b1111_1100 = 0xFC
i2c.write(LIS3MDL_ADDR, &[CTRL_REG1, 0xFC]).await?;

// 3. Configure CTRL_REG2: ±4 gauss (default, 0x00)
i2c.write(LIS3MDL_ADDR, &[CTRL_REG2, 0x00]).await?;

// 4. Configure CTRL_REG3: continuous mode
i2c.write(LIS3MDL_ADDR, &[CTRL_REG3, 0x00]).await?;

// 5. Configure CTRL_REG4: ultra-high performance Z-axis
// OMZ=11 -> 0b0000_1100 = 0x0C
i2c.write(LIS3MDL_ADDR, &[CTRL_REG4, 0x0C]).await?;

Reading Data

const OUT_X_L: u8 = 0x28;

// Read 6 bytes (can also read with auto-increment: 0x28 | 0x80)
let mut data = [0u8; 6];
i2c.write_read(LIS3MDL_ADDR, &[OUT_X_L | 0x80], &mut data).await?;

// Magnetometer (signed 16-bit, gauss)
let mx = i16::from_le_bytes([data[0], data[1]]);
let my = i16::from_le_bytes([data[2], data[3]]);
let mz = i16::from_le_bytes([data[4], data[5]]);

// Convert to physical units
// For ±4 gauss: sensitivity = 6842 LSB/gauss

Embassy I2C Setup for RP2040

use embassy_rp::i2c::{I2c, Config, InterruptHandler};
use embassy_rp::bind_interrupts;
use embassy_rp::peripherals::{I2C0, I2C1};

bind_interrupts!(struct Irqs {
    I2C0_IRQ => InterruptHandler<I2C0>;
    I2C1_IRQ => InterruptHandler<I2C1>;
});

// I2C0 for IMU (LSM6DSOX + LIS3MDL): SDA=GP28, SCL=GP29
let mut config = Config::default();
config.frequency = 400_000; // 400 kHz Fast mode
let i2c0 = I2c::new_async(p.I2C0, p.PIN_29, p.PIN_28, Irqs, config);

// I2C1 for Barometer (BMP390) and Gas Sensor (ENS160): SDA=GP2, SCL=GP3
let i2c1 = I2c::new_async(p.I2C1, p.PIN_3, p.PIN_2, Irqs, config);

Note: Embassy I2C::new_async takes pins as (SCL, SDA) not (SDA, SCL).

I2C Bus Scanning

Use the SCAN command to discover devices on both I2C buses:

// Add to command handler
} else if cmd.starts_with(b"SCAN") {
    use embedded_hal_async::i2c::I2c as I2cTrait;

    let _ = class.write_packet(b"I2C0 scan:\r\n").await;
    for addr in 0x08u8..0x78u8 {
        let mut buf = [0u8; 1];
        if i2c0.read(addr, &mut buf).await.is_ok() {
            // Device found at addr
            let mut msg: heapless::String<16> = heapless::String::new();
            let _ = write!(msg, "  0x{:02X}\r\n", addr);
            let _ = class.write_packet(msg.as_bytes()).await;
        }
    }
    // Repeat for i2c1...
}

Expected output for our hardware:

I2C0 scan:
  0x1C    # LIS3MDL
  0x6A    # LSM6DSOX
I2C1 scan:
  0x53    # ENS160
  0x77    # BMP390

Sensitivity and Conversion

BMP390

Requires calibration coefficients from registers 0x31-0x45. See datasheet section 8.4 for compensation formulas.

LSM6DSOX

Accel Range	Sensitivity
±2 g	0.061 mg/LSB
±4 g	0.122 mg/LSB
±8 g	0.244 mg/LSB
±16 g	0.488 mg/LSB

Gyro Range	Sensitivity
±125 dps	4.375 mdps/LSB
±250 dps	8.75 mdps/LSB
±500 dps	17.5 mdps/LSB
±1000 dps	35 mdps/LSB
±2000 dps	70 mdps/LSB

LIS3MDL

Mag Range	Sensitivity
±4 gauss	6842 LSB/gauss
±8 gauss	3421 LSB/gauss
±12 gauss	2281 LSB/gauss
±16 gauss	1711 LSB/gauss

Troubleshooting

Sensor Not Responding

Check I2C address (measure SDO/SA0/SA1 pin voltage)
Verify pull-up resistors on SDA/SCL (2.2k-10k to 3.3V)
Check wiring: SDA to SDA, SCL to SCL
Reduce I2C frequency to 100kHz for debugging

Wrong WHO_AM_I Value

0xFF: No device responding (check address, wiring)
0x00: Device in reset or powered off
Other: Wrong device or address conflict

No Data Updates

Check power mode (devices start in power-down)
Verify ODR is set (output data rate > 0)
Check STATUS register for data ready flags

I2C Reads Hanging

If sensor reads hang after successful initialization:

Test sensors individually - add debug output between each sensor read to identify which one hangs
Check for I2C bus conflicts - multiple sensors on same bus can cause issues if one holds SDA/SCL low
Add small delays between operations - some sensors need settling time between init and first read
Verify async I2C trait is in scope - must use embedded_hal_async::i2c::I2c as I2cTrait; in each module

Debugging Pattern

When sensor reads aren't working, use this progressive debugging approach:

// Add debug output before/after each operation
let _ = class.write_packet(b"SENSOR_NAME...\r\n").await;
if sensor::read(&mut i2c, &mut data).await.is_err() {
    let _ = class.write_packet(b"SENSOR_NAME ERR\r\n").await;
}
let _ = class.write_packet(b"SENSOR_NAME DONE\r\n").await;

This reveals exactly which operation hangs - invaluable for I2C debugging.

Working Code Reference

The current pico_logger implementation in pico_logger/src/sensors/ provides working drivers for all three sensors. Key patterns:

Each sensor in its own module with init() and read() functions
I2C trait imported in each module: use embedded_hal_async::i2c::I2c as I2cTrait;
Error handling via Result - init returns error if WHO_AM_I doesn't match
Shared SensorData struct passed by mutable reference to reads

name	sensor-drivers
description	Guidance for embedded sensor drivers used in the payload. Use when working with BMP390, ENS160, LSM6DSOX, LIS3MDL, GPS, IMU, barometer, or any sensor integration.
keywords	["bmp390","ens160","lsm6dsox","lis3mdl","gps","imu","barometer","magnetometer","accelerometer","gyroscope","pressure","temperature","altitude","i2c","sensor","embedded-hal"]

name	sensor-drivers
description	Guidance for embedded sensor drivers used in the payload. Use when working with BMP390, ENS160, LSM6DSOX, LIS3MDL, GPS, IMU, barometer, or any sensor integration.
keywords	["bmp390","ens160","lsm6dsox","lis3mdl","gps","imu","barometer","magnetometer","accelerometer","gyroscope","pressure","temperature","altitude","i2c","sensor","embedded-hal"]

sensor-drivers

More from this repository

Payload Sensor Drivers

Hardware Configuration

BMP390 - Barometric Pressure Sensor

Specifications

I2C Address

Key Registers

Power Modes

Initialization Sequence

Reading Data

ENS160 - Digital Metal-Oxide Multi-Gas Sensor

Specifications

I2C Address

Key Registers

Operating Modes

Status Register (0x20)

Initialization Sequence

Reading Data

Temperature/Humidity Compensation

AQI Interpretation

Important Notes

LSM6DSOX - 6-Axis IMU (Accelerometer + Gyroscope)

Specifications

I2C Address

Key Registers

CTRL1_XL (Accelerometer Control)

CTRL2_G (Gyroscope Control)

Initialization Sequence

Reading Data

LIS3MDL - 3-Axis Magnetometer

Specifications

I2C Address

Key Registers

CTRL_REG1 (ODR and XY Performance)

CTRL_REG2 (Full-Scale Selection)

CTRL_REG3 (Operating Mode)

Initialization Sequence

Reading Data

Embassy I2C Setup for RP2040

I2C Bus Scanning

Sensitivity and Conversion

BMP390

LSM6DSOX

LIS3MDL

Troubleshooting

Sensor Not Responding

Wrong WHO_AM_I Value

No Data Updates

I2C Reads Hanging

Debugging Pattern

Working Code Reference

Payload Sensor Drivers

Hardware Configuration

BMP390 - Barometric Pressure Sensor

Specifications

I2C Address

Key Registers

Power Modes

Initialization Sequence

Reading Data

ENS160 - Digital Metal-Oxide Multi-Gas Sensor

Specifications

I2C Address

Key Registers

Operating Modes

Status Register (0x20)

Initialization Sequence

Reading Data

Temperature/Humidity Compensation

AQI Interpretation

Important Notes

LSM6DSOX - 6-Axis IMU (Accelerometer + Gyroscope)

Specifications

I2C Address

Key Registers

CTRL1_XL (Accelerometer Control)

CTRL2_G (Gyroscope Control)

Initialization Sequence

Reading Data