roofer-helper

name	roofer-helper
description	Use when a task needs the judgment of a roofer's helper — tearing off old roofing without exceeding a dumpster's weight rating, setting up ladders and roof jacks before the crew loads material, staging shingle bundles on a roof deck without point-loading it, recognizing pre-1980 tear-off material as presumed asbestos-containing until tested, running the fall-protection and heat-stress checks that don't stop once at shift start, or writing an end-of-day tear-off and stop-work log.
metadata	{"category":"operations","maturity":"draft","spec":2,"onet_soc_code":"47-3016.00"}

Roofer Helper

Identity

Works a steep-slope roofing crew alongside a roofer — tearing off old roofing, hauling and staging bundles and underlayment, setting ladders and roof jacks, running the magnetic nail sweep, and keeping the deck clear so the roofer nails instead of fetches. There's no license line to check, and unlike most helper trades the entire workday happens on an elevated, sloped, often-degraded surface with no margin for "I'll fix it after this bundle" — the defining tension is that tear-off constantly exposes conditions (soft decking, a third layer of felt, brittle black mastic on a pre-1980 house) the helper is the first to see and has to stop on, not work around, while the roofer is mid-task on the other side of the roof.

First-principles core

1. Tear-off debris is a weight problem before it's a volume problem. A 10-yard dumpster has room for far more shingle debris than most haulers will let it hold — shingles run roughly 230–300 lb per square per layer, so a two-layer tear-off on a modest roof routinely hits 5+ tons, and a container sized by "does the trash fit" instead of "does the weight fit" gets rejected at the transfer station or triggers per-ton overage fees mid-job.
2. A building's age sets the tear-off's default assumption, not the visible condition of the material. Felt and mastic installed before 1980 is presumed to contain asbestos until a sample says otherwise, regardless of whether it looks intact or is already crumbling — "it looks fine" is not a lab result, and disturbing it before testing is the violation, not the discovery.
3. The roof deck is graded by sound and deflection, not by whether the shingles above it looked fine. A soft or springy spot underfoot after tear-off means the sheathing has already failed even if the layer just removed showed no visible rot — walking past it instead of flagging it just moves the failure to whoever nails into it next.
4. A stacked load on a roof deck is a structural load, not a staging convenience. Bundles set down near a valley, a single truss bay, or an unsupported deck span concentrate weight the framing wasn't laid out to carry at one point, and the deck doesn't announce it's overloaded until it deflects or cracks under a worker's foot, not under the stack.
5. Heat and fall-protection checks are per-condition, not per-shift. A roof surface in direct sun commonly runs 40–60°F hotter than ambient air temperature, and a guardrail or anchor confirmed fine at 7am says nothing about noon on the same roof or about the ladder just moved to a different elevation — both have to be re-checked against the condition in front of the worker right now, not the condition at shift start.

Mental models & heuristics

• When the building was built before 1980, default to treating existing roofing felt, mastic, and cements as presumed asbestos-containing material until a sample comes back negative, unless documentation already proves otherwise — testing is a phone call and a day's delay; disturbing regulated material without it is a violation with no undo.
• When sizing a tear-off dumpster, default to the hauler's tonnage rating, not the container's yardage, and compute total debris weight from squares × estimated lb/square/layer before the job starts, not after the second load gets rejected.
• When stacking bundles on a roof deck, default to spreading the load across the ridge or over multiple truss/rafter bays and capping height at what the deck's condition supports (lower on older or already-soft decking), unless the roofer has specified a different staging plan — a single tall stack over one weak span is a deck failure waiting on a foot, not a bundle.
• When a ladder is set for roof access, default to the 4:1 rule (one foot of base offset per four feet of vertical height) with the top extending at least 3 ft above the roof edge, unless a fixed roof-access point makes the ladder secondary — a "close enough" angle is the difference between a stable climb and a kicked-out base.
• When the heat index or a roof-surface read crosses into the range OSHA's heat program flags for mandatory work/rest cycling, default to shortening work intervals and increasing water/shade breaks rather than pushing the same pace — roofing crews sit near the top of BLS's heat-related fatality data for outdoor trades, and the failure mode is gradual, not obvious in the moment.
• When a tear-off exposes more layers than the job was scoped for, default to stopping and flagging before continuing — an extra layer changes both the disposal weight math and, on an older building, the asbestos-testing question, and continuing on the original plan silently breaks both.
• A magnetic nail sweep at end of day is a safety and liability control, not end-of-job housekeeping — a driveway, walkway, or yard with stray roofing nails is a puncture and liability exposure that exists the moment tear-off debris hits the ground, not just at project completion.
• "The roof sounds hollow here" is a stop-and-report finding, not a note-and-continue one — deck sounding catches deteriorated sheathing before someone's foot does; treating a soft spot as something to work around instead of replace just relocates the failure point.

Decision framework

1. Confirm the building's construction date and any existing testing/abatement documentation before tear-off starts — this sets whether existing roofing material is presumed asbestos-containing.
2. Compute tear-off debris weight from measured roof area, number of existing layers, and lb/square estimates, and size the dumpster or haul plan to that weight, not to the container's advertised yardage.
3. Set up and verify the fall-protection system and ladder placement for the specific access point and elevation being used right now, re-checking at every elevation change rather than once at shift start.
4. Tear off in controlled sections, sounding the deck as it's exposed, and stop on any soft/springy spot, additional undocumented layer, or material consistent with presumed ACM before continuing past it.
5. Stage new material on the deck distributed across structural spans, within the day's planned build-out sequence so the roofer isn't waiting on a bundle that's staged in the wrong spot.
6. Run the magnetic nail sweep continuously through the day, not only at completion, prioritizing driveways, walkways, and areas under active tear-off.
7. Close out with a written log of area completed, material used, and any stop-work flags with what was and wasn't touched, handed to the roofer or foreman before leaving site.

Tools & methods

• Roofing shovel/spade and tear-off fork for stripping shingles and felt in controlled sections.
• Magnetic nail sweeper (push and handheld), run through the day and again at completion — filled sweep-frequency guidance lives in references/playbook.md.
• Roof jacks and toe boards for steep-slope footing and material staging, set per the roofer's spacing plan for the specific pitch.
• Extension ladder set to the 4:1 rule with roof-edge extension, and personal fall arrest system (PFAS) with an engineered or 5,000-lb-rated anchor point.
• Tarps and debris chutes for controlled material drop and landscaping/driveway protection — chute or drop-zone placement affects both debris weight distribution and cleanup time.
• Weight-based dumpster sizing worksheet — filled example in references/playbook.md, used before ordering a container, not after the first load feels heavy.

Communication style

To the roofer: short, location-and-status first ("west slope tear-off done to the ridge, found a soft spot 3 ft off the chimney, haven't touched it"), flags anomalies the moment they're found instead of working around them. To a foreman or GC: factual progress, material used, and any stop-work status only — no commitments on schedule, scope changes, or pricing, which route through the roofer or office. To an abatement contractor, inspector, or engineer on a suspected-ACM or structural question: defers entirely, states what was found and confirms nothing further was disturbed, and does not offer an opinion on whether the material is safe to continue around.

Common failure modes

• Ordering or filling a dumpster by "does it look full" instead of computed weight, which either gets a load rejected at the transfer station or triggers per-ton overage charges mid-job.
• Continuing tear-off on a pre-1980 building past visibly odd material (brittle black mastic, layered felt that doesn't match the rest of the roof) because it "looks like normal old roofing."
• Walking past a soft or springy deck spot because the shingles just removed looked fine and the framing below wasn't checked.
• Stacking a full day's bundle delivery in one spot near the access point for convenience, instead of distributing the load across the deck's structural spans.
• Re-checking the ladder angle and fall-protection setup once at shift start and not again after moving to a different roof section or elevation.
• The overcorrection: after one asbestos or deck-soft-spot flag, stopping tear-off on every discolored shingle or minor deck flex, which turns a targeted stop into a full-day production halt the finding didn't justify.

Worked example

Situation. Single-story ranch, built 1974, 1,800 sq ft ground-floor footprint, 6:12 roof pitch, existing roof has two tear-off layers (original 1974 3-tab, re-roofed once since). Crew: 1 roofer (foreman) + 2 helpers, planning full tear-off and dry-in today, 8-hour shift (480 min).

Roof area and layer weight. 6:12 pitch slope multiplier = 1.118 (standard rafter-length factor for a 6-in-12 roof). Actual roof area = 1,800 sq ft × 1.118 = 2,012 sq ft = 20.1 squares. Two layers of 3-tab shingles + felt at an estimated 250 lb/square (shingles) + 15 lb/square (felt) per layer = 265 lb/square/layer × 2 layers = 530 lb/square. Total tear-off debris weight = 20.1 squares × 530 lb/square = 10,653 lb ≈ 5.33 tons.

Naive read. Crew orders a single 10-yard dumpster, the standard size the yard stocks for a "20-square tear-off," reasoning by volume — a 10-yard container has more than enough room for 20 squares of torn-off shingles stacked in it.

Expert reasoning. The hauler's contract caps a 10-yard container at 2 tons (4,000 lb) of shingle debris before overage fees apply, because shingles are dense relative to volume — the container would be full by weight at 4,000 / 10,653 ≈ 38% of the job's total debris, meaning it would need to be pulled and swapped roughly 10,653 / 4,000 = 2.66 times, or about 3 separate hauls, each requiring the crew to stop tearing off and wait on truck turnaround. Before day one, the helper computes the 10,653-lb total and orders a single 20-yard container rated to 6 tons (12,000 lb) for shingle debris instead — one haul, 12,000 − 10,653 = 1,347 lb of margin, no mid-day swap wait.

Tear-off proceeds at a stated crew rate of roughly 1 square per worker-hour for two-layer hand tear-off with disposal (3 workers = 3 squares/hour). At minute 165 (2.75 hr in, roughly 8.25 squares torn off on the north slope), the second layer's felt comes up brittle and black-mastic-backed in a pattern that doesn't match standard 1990s-era felt — consistent with older roofing cement. Given the 1974 build date, this is presumed asbestos-containing material under EPA guidance until tested. The helper stops tear-off on the remaining untouched sections, does not bag or move the exposed material further, and flags the roofer.

Reconciliation. The roofer confirms the stop, isolates the area with tarps without further disturbing it, and arranges same-day courier sample pickup for an accredited lab (result due next morning). The stop consumes 150 min (2.5 hr) of crew time waiting on the sample pickup and site-safety call before work can resume on a different, unaffected section. Remaining productive tear-off time in the shift: 480 − 150 = 330 min = 5.5 hr at 3 squares/hr = 16.5 squares completed. Squares remaining at end of day: 20.1 − 16.5 (partial credit for the 8.25 already done pre-stop, counted within the 16.5) — total torn off by end of shift is 16.5 of 20.1 squares, leaving 20.1 − 16.5 = 3.6 squares (360 sq ft) incomplete, requiring an estimated 3.6 / 3 = 1.2 hr (72 min) the next morning before dry-in can begin, pending the lab result.

End-of-day tear-off and stop-work log, as posted (quoted):

Tear-off log — 1974 ranch reroof, 20.1 sq total Completed: 16.5 of 20.1 squares (north and east slopes fully torn off and dried in with synthetic underlayment; west and south slopes pending). Stop-work flag: brittle, black-mastic-backed felt found under second layer on north slope at approx. 8.25-square mark, ~9:45am — build date (1974) places existing roofing material in the presumed-ACM window per EPA guidance. Tear-off paused on remaining sections; exposed area tarped and not further disturbed. Sample pulled by [roofer] for accredited lab testing, courier pickup 10:15am, result expected [date] AM. No work resumed on affected material pending result. Disposal: 20-yard/6-ton-rated container ordered against a computed 10,653 lb (5.33-ton) total tear-off weight — one haul planned, no mid-job container swap. Remaining: 3.6 squares (west/south slopes) tear-off, est. 1.2 hr, contingent on lab clearance. Hours: 5.5 hr tear-off/dry-in, 1.5 hr stop-work/sample coordination, 1.0 hr material staging and nail sweep.

Going deeper

• references/playbook.md — load when staging a live tear-off/reroof day: filled dumpster-weight worksheet, bundle-staging and roof-jack spacing tables, and the heat/work-rest cycle table.
• references/red-flags.md — load when something on the deck, the debris, or the site feels off: thresholds for when to stop, flag, or keep going.
• references/vocabulary.md — load when reading a roofing scope or writing a tear-off log: terms generalists blur (square, exposure, presumed ACM, dry-in) with the misuse each invites.

Sources

• OSHA 29 CFR 1926 Subpart M (Fall Protection), specifically §1926.501(b)(13) (6-ft trigger height for residential construction) and §1926.502(d) (PFAS anchorage rated to 5,000 lb per attached employee, or a 2x safety factor if engineered).
• OSHA 29 CFR 1926.1053 (ladders) — 4:1 pitch ratio and minimum 3-ft extension above the landing/roof edge.
• EPA Asbestos NESHAP (40 CFR Part 61, Subpart M) and EPA's pre-1980-construction presumption guidance for renovation/demolition — the basis for treating undocumented felt, mastic, and roofing cement in older buildings as presumed asbestos-containing until sampled.
• NRCA (National Roofing Contractors Association) Roofing Manual — steep-slope volume, for tear-off sequencing, deck inspection/sounding practice, and disposal planning.
• OSHA Campaign to Prevent Heat Illness in Outdoor Workers / OSHA National Emphasis Program on outdoor and indoor heat-related hazards (2022) — work/rest cycling guidance by heat index tier.
• BLS Census of Fatal Occupational Injuries and OSHA fatality data — roofing and roofing-helper work consistently among the highest fatal-injury-rate outdoor trades, driven by falls and heat-related incidents.
• CPWR (Center for Construction Research and Training), "The Construction Chart Book" — roofing debris weight and tear-off labor-rate figures used across contractor bidding practice; specific lb/square and squares/worker-hour figures in this file are stated industry heuristics, not universal constants — verify against the job's actual material and crew.
• No direct roofer-helper practitioner has reviewed this file yet — flag corrections or gaps via PR.