embedded-iot

name	embedded-iot
description	Embedded systems firmware, microcontrollers (ESP32, STM32, Arduino, Raspberry Pi), RTOS (FreeRTOS, Zephyr), IoT protocols (MQTT, CoAP, BLE), bare-metal C/C++, and hardware peripheral interfaces (I2C, SPI, UART, GPIO). Use when developing firmware, working with microcontrollers, or building IoT devices.

Embedded Systems & IoT

Microcontroller Platforms

Platform	Best For	Language	IDE
ESP32	WiFi/BLE IoT devices	C/C++, MicroPython	PlatformIO, Arduino IDE
STM32	Industrial, real-time	C/C++	STM32CubeIDE, PlatformIO
Arduino	Prototyping, learning	C++ (Arduino)	Arduino IDE, PlatformIO
Raspberry Pi Pico	RP2040, dual-core	C/C++, MicroPython	Thonny, VS Code
nRF52	BLE-focused IoT	C, Zephyr	nRF Connect SDK

Firmware Patterns

GPIO & Peripherals

// ESP-IDF GPIO example
gpio_config_t io_conf = {
    .pin_bit_mask = (1ULL << GPIO_NUM_2),
    .mode = GPIO_MODE_OUTPUT,
    .pull_up_en = GPIO_PULLUP_DISABLE,
    .pull_down_en = GPIO_PULLDOWN_DISABLE,
    .intr_type = GPIO_INTR_DISABLE,
};
gpio_config(&io_conf);
gpio_set_level(GPIO_NUM_2, 1);

I2C Communication

// Read sensor via I2C
i2c_cmd_handle_t cmd = i2c_cmd_link_create();
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (SENSOR_ADDR << 1) | I2C_MASTER_WRITE, true);
i2c_master_write_byte(cmd, REG_TEMP, true);
i2c_master_start(cmd);
i2c_master_write_byte(cmd, (SENSOR_ADDR << 1) | I2C_MASTER_READ, true);
i2c_master_read(cmd, data, 2, I2C_MASTER_LAST_NACK);
i2c_master_stop(cmd);
i2c_master_cmd_begin(I2C_NUM_0, cmd, pdMS_TO_TICKS(1000));
i2c_cmd_link_delete(cmd);

RTOS (FreeRTOS)

// Task creation
void sensor_task(void *pvParameters) {
    while (1) {
        float temp = read_temperature();
        xQueueSend(data_queue, &temp, portMAX_DELAY);
        vTaskDelay(pdMS_TO_TICKS(1000));
    }
}
xTaskCreate(sensor_task, "sensor", 4096, NULL, 5, NULL);

// Mutex for shared resources
SemaphoreHandle_t spi_mutex = xSemaphoreCreateMutex();
if (xSemaphoreTake(spi_mutex, pdMS_TO_TICKS(100)) == pdTRUE) {
    spi_transfer(data);
    xSemaphoreGive(spi_mutex);
}

IoT Protocols

MQTT

// ESP-IDF MQTT client
esp_mqtt_client_config_t mqtt_cfg = {
    .broker.address.uri = "mqtt://broker.hivemq.com",
};
esp_mqtt_client_handle_t client = esp_mqtt_client_init(&mqtt_cfg);
esp_mqtt_client_start(client);
esp_mqtt_client_publish(client, "/sensors/temp", "23.5", 0, 1, 0);

Key IoT Protocols

Protocol	Transport	Use Case
MQTT	TCP/TLS	Pub/sub messaging, telemetry
CoAP	UDP/DTLS	Constrained devices, REST-like
BLE	Radio	Short-range, low power
LoRaWAN	Radio	Long-range, low data rate
Matter	IP	Smart home interoperability

Best Practices

• Power management: Deep sleep modes, wake-on-interrupt, duty cycling
• Watchdog timers: Always enable, reset periodically, catch firmware hangs
• OTA updates: Dual partition scheme, rollback on boot failure, signature verification
• Memory: Static allocation preferred, avoid heap fragmentation, use memory pools
• Testing: Hardware-in-the-loop (HIL), mock hardware interfaces for unit tests