メニュー
Deploy a Hubitat app or driver's Groovy source to a hub and confirm it saved and runs by watching the log stream. Use when the user wants to deploy, push, upload, or install app/driver code onto a Hubitat hub, or iterate the edit-deploy-check loop.
Codex または Claude でインストール この Prompt をコピーして Codex、Claude、または他のアシスタントに貼り付けると、Skill ページを確認してインストールできます。
SOC 職業分類に基づく
| name | deploy |
| description | Deploy a Hubitat app or driver's Groovy source to a hub and confirm it saved and runs by watching the log stream. Use when the user wants to deploy, push, upload, or install app/driver code onto a Hubitat hub, or iterate the edit-deploy-check loop. |
Process steps in order. Do not skip ahead.
This replaces the copy-paste-into-the-browser loop. Code operations are per-hub by IP (multi-hub-topology rule). Hub connection details come from hubs.json (see Skill(skill: "hub-config")); pass --ip directly if there is no config yet.
Confirm: the source file, the kind (app or driver), the target hub (a hubs.json name via --hub, or an --ip), and whether this is a new entry or an update to an existing one. If updating an existing entry whose id is unknown, it is matched by the name in the source's definition.
Proceed to Step 2.
Run Skill(skill: "lint-review") on the source first. A deploy of code with a missing-command or bad import wastes a round-trip — the hub rejects malformed code on save. If lint is clean or the user accepts the findings, proceed to Step 3.
python3 .tessl/plugins/jbaruch/hubitat-dev/skills/_scripts/hub_deploy.py \
--kind <kind> --source <file.groovy> [--name "<name>" | --id <id>] [--hub <name> | --ip <addr>]
Argument and output contract, and the create-vs-update decision: skills/_scripts/hub_deploy.py module docstring; the shared logic is in skills/_scripts/hubclient.py. The script prints {action, id, ...} on success.
skills/_scripts/hub_pull.py), reconcile the difference with the user, then deploy again. Do not loop the deploy.Proceed to Step 4.
A successful save means the code compiled, not that it behaves. Confirm runtime behavior by watching the hub while exercising the code — hand off to Skill(skill: "debug") filtered to this app/driver's name. For a driver, have the user (or Maker API) trigger a device command; for an app, press Done / fire the trigger. Finish here.
Move every app reference from an old Hubitat device onto a new one — via Settings → Swap Device where possible, a virtual-device bridge or parking slot where the swap list blocks it, and a guided manual re-select where neither works. Use when the user wants to swap, migrate, replace, or move a device's references to a different device, re-home a device to a different hub over Hub Mesh, or asks why a device does not appear in the Swap Device list.
Diagnose Hubitat Z-Wave and Zigbee network problems — ghost/failed nodes, packet errors, weak routes, dead or unjoined Zigbee devices, devices that stopped responding to commands, a broken hub-mesh link, an unhealthy mesh. Use when the user wants to check mesh health, find ghost nodes, debug a flaky/slow/dead Z-Wave or Zigbee device, or figure out why the radio network misbehaves.
Safely remove a Hubitat device — enumerate where it's used, warn about the blast radius before deleting, verify references cleared after, and re-wire them onto a replacement device. Use when the user wants to remove, delete, retire, or replace a device, or asks what a device is used by before deleting it.
Update Z-Wave device firmware on a Hubitat hub via the native zwaveJS updater — discover installed versions, find vendor-latest firmware, stage it, and batch-flash safely with a radio-hang watchdog. Use when the user wants to update/flash device firmware, check which devices are behind on firmware, or fix a device whose issue a firmware update addresses.
Tail a Hubitat hub's live log or event websocket, filtered, and interpret it against the code to diagnose an app or driver. Use when the user wants to debug, watch logs, tail the log stream, see live events, or figure out why a Hubitat app/driver misbehaves.
Manage the hubs.json config that records how to reach each Hubitat hub by IP for code operations. Actions — init a config, add a hub, set the default hub, remove a hub, list hubs. Use when the user wants to configure, register, add, or list Hubitat hubs for deploy/pull/debug.