원클릭으로 Manus에서 모든 스킬 실행

시작하기

robotrace-flash-debug

스타4

포크1

업데이트2026년 6월 28일 03:17

STM32CubeCLT、STM32_Programmer_CLI、ST-Linkを使ってrobotrace_v2へ書き込みやデバッグを行うときに使う。実機接続条件、ビルド、書き込み、空転確認、緊急停止無効化条件を扱う。

설치

Codex 또는 Claude로 설치 이 Prompt를 복사해 Codex, Claude 또는 다른 어시스턴트에 붙여 넣으면 Skill 페이지를 검토하고 설치를 진행할 수 있습니다.

Manus에서 실행

출처

Kageyana

Kageyana/robotrace_v2

GitHub 저장소 열기 Creator 저장소 보기

다운로드

Manus에서 실행

Robotrace Flash Debug

Overview

Use this skill for firmware build, flash, and ST-Link debug workflows. Keep command definitions and safety policy in AGENTS.md as the source of truth.

Preconditions

Build before flashing.
Flash only when the robot and ST-Link are connected.
Debugging with ST-Link is allowed.
Real running is not allowed during wired ST-Link debugging.
The robot may be lifted for no-load motor checks, but it will not move forward and can quickly hit emergency-stop conditions.
Disable emergency-stop conditions only for no-load, stationary, or non-moving checks where the target observation is possible without real travel.

Build Commands

Run from robotrace_v2/:

cmake --preset Debug
cmake --build --preset Debug

For release:

cmake --preset Release
cmake --build --preset Release

If tools are missing, do not report build success. Report the missing tool or failed command.

Flash Workflow

Confirm ST-Link and robot connection.
Build the intended preset.
Run the configured VS Code task or equivalent STM32_Programmer_CLI SWD command.
Confirm the flash command exits successfully.
Report command, success/failure, and connection condition.

Debug Workflow

Confirm robot and ST-Link are wired.
Use the configured launch setting:
- Build & Debug Microcontroller - ST-Link
- Attach to Microcontroller - ST-Link
Do not perform real running while wired.
For lifted no-load checks, clearly state that encoder-stop or movement-related emergency stops may trigger.
If emergency-stop conditions are disabled for debug, state which condition, why, and what risk remains.

Post-Flash Checks

Confirm the write command completed normally.
Sensor checks happen through initSystem().
Motor no-load check is not required by default.
Before high-speed running, confirm sensors initialized normally.
High-speed running requires at least 7.5 V battery voltage by operation policy.

이 저장소의 다른 Skills

같은 저장소

robotrace-sd-settings

Kageyana/robotrace_v2

robotrace_v2のSDカード内設定ファイルを読む、書く、修復する、保存形式を変更するときに使う。targetSpeeds.txt、PID設定、lsval.txt、lognum.txt、analysis.txt、boostログの形式を扱う。

2026-06-284

robotrace-hardware-review

Kageyana/robotrace_v2

robotrace_v2の機体、KiCad回路、CubeMX ioc、センサー配置、配線、電源、ピン割り当て、機体寸法変更を確認するときに使う。ハード変更のコード反映確認も扱う。

2026-06-284

robotrace-log-analysis

Kageyana/robotrace_v2

ロボトレース走行ログを解析、比較、可視化するときに使う。CSVログ、XY軌跡、速度追従、角速度、スリップ、ラップタイム比較、autoStart 5走比較、emcStopやcntlog欠落の判定を扱う。

2026-06-284

robotrace-tuning

Kageyana/robotrace_v2

ロボトレースのPID、速度フィードフォワード、スリップ判定、速度・加速度パラメータを調整するときに使う。走行ログ比較、再現性判断、速度向上、変更後10本ログ確認を扱う。

2026-06-284

name	robotrace-flash-debug
description	STM32CubeCLT、STM32_Programmer_CLI、ST-Linkを使ってrobotrace_v2へ書き込みやデバッグを行うときに使う。実機接続条件、ビルド、書き込み、空転確認、緊急停止無効化条件を扱う。

Robotrace Flash Debug

Overview

Use this skill for firmware build, flash, and ST-Link debug workflows. Keep command definitions and safety policy in AGENTS.md as the source of truth.

Preconditions

Build before flashing.
Flash only when the robot and ST-Link are connected.
Debugging with ST-Link is allowed.
Real running is not allowed during wired ST-Link debugging.
The robot may be lifted for no-load motor checks, but it will not move forward and can quickly hit emergency-stop conditions.
Disable emergency-stop conditions only for no-load, stationary, or non-moving checks where the target observation is possible without real travel.

Build Commands

Run from robotrace_v2/:

cmake --preset Debug
cmake --build --preset Debug

For release:

cmake --preset Release
cmake --build --preset Release

If tools are missing, do not report build success. Report the missing tool or failed command.

Flash Workflow

Confirm ST-Link and robot connection.
Build the intended preset.
Run the configured VS Code task or equivalent STM32_Programmer_CLI SWD command.
Confirm the flash command exits successfully.
Report command, success/failure, and connection condition.

Debug Workflow

Confirm robot and ST-Link are wired.
Use the configured launch setting:
- Build & Debug Microcontroller - ST-Link
- Attach to Microcontroller - ST-Link
Do not perform real running while wired.
For lifted no-load checks, clearly state that encoder-stop or movement-related emergency stops may trigger.
If emergency-stop conditions are disabled for debug, state which condition, why, and what risk remains.

Post-Flash Checks

Confirm the write command completed normally.
Sensor checks happen through initSystem().
Motor no-load check is not required by default.
Before high-speed running, confirm sensors initialized normally.
High-speed running requires at least 7.5 V battery voltage by operation policy.