원클릭으로 Manus에서 모든 스킬 실행

sdd-continue

스타6

포크0

업데이트2026년 5월 31일 18:34

Continue evolving an existing scope spec — extend (add requirements/tools/contracts) or pivot (replace decisions). Auto-resolves the scope spec. Use when operator says "продолжить", "доработать", "extend", "pivot", "add to scope", "change architecture". Mode (refine vs pivot) auto-detected from intake verb.

설치

Codex 또는 Claude로 설치 이 Prompt를 복사해 Codex, Claude 또는 다른 어시스턴트에 붙여 넣으면 Skill 페이지를 검토하고 설치를 진행할 수 있습니다.

Manus에서 실행

출처

RubaXa

RubaXa/gennady

GitHub 저장소 열기 Creator 저장소 보기

다운로드

Manus에서 실행

관련 직업SOC

SOC 직업 분류 기준

기타 컴퓨터 관련 직업컴퓨터 및 수학직·SOC 15-1299

SKILL.md

readonly

name	sdd-continue
description	Continue evolving an existing scope spec — extend (add requirements/tools/contracts) or pivot (replace decisions). Auto-resolves the scope spec. Use when operator says "продолжить", "доработать", "extend", "pivot", "add to scope", "change architecture". Mode (refine vs pivot) auto-detected from intake verb.
compatibility	opencode

Extract intent. Operator wants to evolve existing scope spec — refine or pivot. Resolve scope: ask if not given, then ls specs/<scope-name>/<scope-name>.spec.md to verify it exists.
Load & activate directive. Read in full: ~/Developer/gennady/ai/directives/sdd/discovery.directive.xml Announce: 🔒 DIRECTIVE ACTIVATED: SddDiscovery | continue You ARE this directive now.
Apply directive to intent. Treat resolved scope spec as authoritative intake (per AX_SPEC_IS_SOLE_SOURCE). Mode MUST be refine or pivot — greenfield is forbidden in this skill. Follow Execution_Plan end-to-end.

이 저장소의 다른 Skills

같은 저장소

agent-inbox

RubaXa/gennady

Интерактивный ассистент по входящим GitLab MR, где я ревьювер/упомянут. Интенты list/tick/loop/reset. list — интерактивный разбор (Ask, диалог, постинг через vcs-reply после согласования). tick (=once/sync) — один проход без диалога, показывает дельту (что нового). loop — повторение tick планировщиком (частота задаётся снаружи). reset — чистый лист. Use when пользователь говорит «agent-inbox», «разбери входящие», «inbox list», «inbox tick», «что от меня ждут по ревью».

2026-06-296

sdd-hooks-install

RubaXa/gennady

Install Claude Code hooks for live SDD subagent progress streaming. Adds PreToolUse / PostToolUse / SubagentStop entries to project's .claude/settings.json (merging with existing config), ensures .claude/sdd-progress.ndjson is gitignored, prints the operator's tail command. Use once per project before running /sdd-execute or /sdd-execute-batch when live progress visibility is wanted. Idempotent — safe to re-run.

2026-06-286

workspace-permission-setup

RubaXa/gennady

Configure .claude/settings.json so the agent works autonomously inside the current repository while being auto-denied access to anything outside it (home directory, system paths, network, secrets). Use when the user wants to enable AI-first development with minimal permission prompts, scope the agent to a workspace, set up safe autonomy for a project, stop the agent from leaving the repo, reduce repetitive approval requests, or harden permissions for a codebase.

2026-06-286

prd-interview

RubaXa/gennady

От идеи к PRD/EARS через интервью в несколько раундов. Ресёрч кодбазы, неудобные вопросы, подсветка граничных случаев, визуализация (widget или ASCII). На выходе — PRD.md с требованиями в синтаксисе EARS; в конце предлагает сохранить / отдать дальше / начать разработку. Use when пользователь говорит «сделай PRD», «PRD через интервью», «проинтервьюируй меня по фиче», «от идеи к плану», «EARS-требования», «prd-interview».

2026-06-246

sdd-check

RubaXa/gennady

Verify entire SDD workflow integrity — specs linked, trackers synced, execution logs complete, DAGs consistent, file headers correct, tests passing. Read-only, no modifications.

2026-06-046

sdd-execute

RubaXa/gennady

Execute ONE task ticket end-to-end. Reads ticket header + Phases Overview + Execution Log to plan; dispatches one phase-subagent per pending phase (sequential), threading typed Handoff between them; closes Round and dispatches audit-subagent (fresh-eyes). On audit FAIL — re-runs ONLY failing-phases as `fix` kind, max 1 retry. Use when operator passes a Task-ID, ticket path, or "next" / "следующую" / "выбери" / "pick one".

2026-06-046

name	sdd-continue
description	Continue evolving an existing scope spec — extend (add requirements/tools/contracts) or pivot (replace decisions). Auto-resolves the scope spec. Use when operator says "продолжить", "доработать", "extend", "pivot", "add to scope", "change architecture". Mode (refine vs pivot) auto-detected from intake verb.
compatibility	opencode

Extract intent. Operator wants to evolve existing scope spec — refine or pivot. Resolve scope: ask if not given, then ls specs/<scope-name>/<scope-name>.spec.md to verify it exists.
Load & activate directive. Read in full: ~/Developer/gennady/ai/directives/sdd/discovery.directive.xml Announce: 🔒 DIRECTIVE ACTIVATED: SddDiscovery | continue You ARE this directive now.
Apply directive to intent. Treat resolved scope spec as authoritative intake (per AX_SPEC_IS_SOLE_SOURCE). Mode MUST be refine or pivot — greenfield is forbidden in this skill. Follow Execution_Plan end-to-end.