원클릭으로 Manus에서 모든 스킬 실행

waveshare-amoled

스타0

포크0

업데이트2026년 5월 17일 08:41

Development reference for Waveshare ESP32-S3-Touch-AMOLED-1.8. Use when working with this device, its AMOLED display (SH8601 QSPI), touch (FT3168), audio (ES8311), power (AXP2101), IMU (QMI8658), or RTC (PCF85063).

설치

Codex 또는 Claude로 설치 이 Prompt를 복사해 Codex, Claude 또는 다른 어시스턴트에 붙여 넣으면 Skill 페이지를 검토하고 설치를 진행할 수 있습니다.

Manus에서 실행

출처

Sandjab

Sandjab/Waveshare-ESP32

GitHub 저장소 열기 Creator 저장소 보기

다운로드

Manus에서 실행

Waveshare ESP32-S3-Touch-AMOLED-1.8

Quick Reference Card

Spec	Value
MCU	ESP32-S3R8 — Xtensa dual-core 240 MHz, WiFi + BLE 5
Flash / PSRAM	16 MB Flash (Quad SPI) / 8 MB PSRAM (Octal SPI)
Display	1.8" AMOLED, 368x448, SH8601 QSPI
Touch	FT3168 capacitive, I2C (0x38)
Audio	ES8311 codec (I2S + I2C ctrl), speaker + mic, PA on GPIO 46
Power	AXP2101 PMIC, I2C (0x34) — USB 5V / Li-ion
IMU	QMI8658 6-axis (accel + gyro), I2C (0x6B)
RTC	PCF85063 real-time clock, I2C (0x51)
I/O Expander	XCA9554 (TCA9554), I2C (0x20) — LCD ctrl, PMU INT, SD power
Storage	MicroSD (SDMMC 1-wire)
USB	Type-C, native USB CDC
Framework	PlatformIO (ESP-IDF + Arduino)

GPIO Quick Reference (ESP32-S3)

Function	GPIOs	Interface
Display (SH8601)	CLK:11 D0:4 D1:5 D2:6 D3:7 CS:12	QSPI
Touch (FT3168)	SDA:15 SCL:14 INT:21	I2C (0x38)
Audio (ES8311)	MCK:16 BCK:9 WS:45 DI:10 DO:8 PA:46	I2S + I2C (0x18)
I2C bus	SDA:15 SCL:14	Shared: touch, PMIC, IMU, RTC, codec, expander
SD Card (SDMMC)	CLK:2 CMD:1 D0:3	SDMMC 1-wire
AXP2101 PMIC	via I2C (0x34)	Power management
QMI8658 IMU	via I2C (0x6B)	6-axis accel + gyro
PCF85063 RTC	via I2C (0x51)	Real-time clock
XCA9554 expander	via I2C (0x20)	LCD ctrl, SD power, PMU INT

Flash (PlatformIO)

# Build + upload via USB
pio run -t upload

# Monitor serial
pio device monitor -b 115200

Progressive Disclosure Index

For deeper information, consult these files in order:

esp32-platform.md — PlatformIO setup, toolchain, common libraries (reusable for any ESP32-S3 project)
device-hardware.md — Single-MCU architecture, complete pinout, ICs, display, power (AXP2101), audio (ES8311)
resources.md — Official links, datasheets, community projects, repos

Convention : esp32-platform.md contains generic ESP32-S3/PlatformIO knowledge. device-hardware.md contains everything specific to this Waveshare device.

이 저장소의 다른 Skills

같은 저장소

waveshare-esp32

Sandjab/Waveshare-ESP32

Common ESP32-S3 platform reference for all Waveshare devices in this monorepo. Use when working with PlatformIO setup, toolchain, common libraries, or adding a new device.

2026-06-090

waveshare-epaper-154g

Sandjab/Waveshare-ESP32

Development reference for Waveshare ESP32-S3-ePaper-1.54G (200×200 4-color e-paper, ES8311 audio, SHTC3, PCF85063 RTC, battery). Use when working with this device, its e-paper display (EPD_1in54g driver), power rails, audio codec, sensors, deep-sleep, or restoring the factory firmware.

2026-06-090

waveshare-amoled-175c

Sandjab/Waveshare-ESP32

Development reference for Waveshare ESP32-S3-Touch-AMOLED-1.75C (round 1.75" watch form factor). Use when working with this device, its AMOLED display (CO5300 QSPI 466×466), touch (CST9217), audio (ES8311 playback + ES7210 mic-array AEC), power (AXP2101), IMU (QMI8658), or restoring the factory firmware.

2026-05-170

guition-k718

Sandjab/Waveshare-ESP32

Development reference for Guition JC3636K718 (ESP32-S3, round 1.8" 360×360 + encoder + RGB ring). Use when working with this device, its display (ST77916 QSPI), audio chain (PCM5100A DAC + NS4150B amp), 13× WS2812 ring on GPIO 0, encoder, microphone, DRV2605 + LRA haptics, or restoring the factory firmware.

2026-05-170

waveshare-knob

Sandjab/Waveshare-ESP32

Development reference for Waveshare ESP32-S3-Knob-Touch-LCD-1.8. Use when working with this device, its dual-MCU architecture, display (ST77916 QSPI), touch (CST816), haptics (DRV2605), or audio (PCM5100A).

2026-05-170

name	waveshare-amoled
description	Development reference for Waveshare ESP32-S3-Touch-AMOLED-1.8. Use when working with this device, its AMOLED display (SH8601 QSPI), touch (FT3168), audio (ES8311), power (AXP2101), IMU (QMI8658), or RTC (PCF85063).

Waveshare ESP32-S3-Touch-AMOLED-1.8

Quick Reference Card

Spec	Value
MCU	ESP32-S3R8 — Xtensa dual-core 240 MHz, WiFi + BLE 5
Flash / PSRAM	16 MB Flash (Quad SPI) / 8 MB PSRAM (Octal SPI)
Display	1.8" AMOLED, 368x448, SH8601 QSPI
Touch	FT3168 capacitive, I2C (0x38)
Audio	ES8311 codec (I2S + I2C ctrl), speaker + mic, PA on GPIO 46
Power	AXP2101 PMIC, I2C (0x34) — USB 5V / Li-ion
IMU	QMI8658 6-axis (accel + gyro), I2C (0x6B)
RTC	PCF85063 real-time clock, I2C (0x51)
I/O Expander	XCA9554 (TCA9554), I2C (0x20) — LCD ctrl, PMU INT, SD power
Storage	MicroSD (SDMMC 1-wire)
USB	Type-C, native USB CDC
Framework	PlatformIO (ESP-IDF + Arduino)

GPIO Quick Reference (ESP32-S3)

Function	GPIOs	Interface
Display (SH8601)	CLK:11 D0:4 D1:5 D2:6 D3:7 CS:12	QSPI
Touch (FT3168)	SDA:15 SCL:14 INT:21	I2C (0x38)
Audio (ES8311)	MCK:16 BCK:9 WS:45 DI:10 DO:8 PA:46	I2S + I2C (0x18)
I2C bus	SDA:15 SCL:14	Shared: touch, PMIC, IMU, RTC, codec, expander
SD Card (SDMMC)	CLK:2 CMD:1 D0:3	SDMMC 1-wire
AXP2101 PMIC	via I2C (0x34)	Power management
QMI8658 IMU	via I2C (0x6B)	6-axis accel + gyro
PCF85063 RTC	via I2C (0x51)	Real-time clock
XCA9554 expander	via I2C (0x20)	LCD ctrl, SD power, PMU INT

Flash (PlatformIO)

# Build + upload via USB
pio run -t upload

# Monitor serial
pio device monitor -b 115200

Progressive Disclosure Index

For deeper information, consult these files in order:

esp32-platform.md — PlatformIO setup, toolchain, common libraries (reusable for any ESP32-S3 project)
device-hardware.md — Single-MCU architecture, complete pinout, ICs, display, power (AXP2101), audio (ES8311)
resources.md — Official links, datasheets, community projects, repos

Convention : esp32-platform.md contains generic ESP32-S3/PlatformIO knowledge. device-hardware.md contains everything specific to this Waveshare device.