Execute qualquer Skill no Manus
com um clique

Execute qualquer Skill no Manus com um clique

waveshare-epaper-154g

Estrelas0

Forks0

Atualizado9 de junho de 2026 às 21:47

Development reference for Waveshare ESP32-S3-ePaper-1.54G (200×200 4-color e-paper, ES8311 audio, SHTC3, PCF85063 RTC, battery). Use when working with this device, its e-paper display (EPD_1in54g driver), power rails, audio codec, sensors, deep-sleep, or restoring the factory firmware.

Instalação

Instalar com Codex ou Claude Copie este prompt, cole no Codex, Claude ou outro assistente e deixe que ele revise a página da skill e instale para você.

Executar no Manus

Fonte

Sandjab

Sandjab/Waveshare-ESP32

Abrir repositório GitHub Ver repositórios do creator

Download

Executar no Manus

Ocupações relacionadasSOC

Baseado na classificação ocupacional SOC

Desenvolvedores de softwareInformática e Matemática·SOC 15-1252

Explorador de arquivos

3 arquivos

SKILL.md

readonly

name	waveshare-epaper-154g
description	Development reference for Waveshare ESP32-S3-ePaper-1.54G (200×200 4-color e-paper, ES8311 audio, SHTC3, PCF85063 RTC, battery). Use when working with this device, its e-paper display (EPD_1in54g driver), power rails, audio codec, sensors, deep-sleep, or restoring the factory firmware.

Waveshare ESP32-S3-ePaper-1.54G

Quick Reference Card

Spec	Value
MCU	ESP32-S3-PICO-1 (LGA56) — Xtensa LX7 dual-core 240 MHz, WiFi + BLE 5
Flash / PSRAM	8 MB Flash (QIO) / 8 MB PSRAM (OPI) — embarquées dans le package, vérifié `esptool flash_id`
Display	1.54" e-paper 200×200, 4 couleurs (noir/blanc/jaune/rouge), SPI, driver vendor `EPD_1in54g`
Refresh	~20 s full, ~15 s fast — UI statique uniquement
Audio	ES8311 codec (I2C 0x18) : speaker MX1.25 (via ampli, ctrl GPIO 46) + micro
Sensors	SHTC3 temp/humidité (I2C 0x70), PCF85063 RTC (I2C 0x51)
Storage	TF card slot (SDMMC 1-bit)
Power	USB-C 5V / Li-ion MX1.25 (ETA6098 charger, VBAT sense ADC GPIO 4)
USB	Type-C, CDC natif exposé par le firmware usine (pas de BOOT dance au 1er flash)
Framework	PlatformIO Arduino (`qio_opi`, 8MB, `default_8MB.csv`) ; vendor : Arduino-ESP32 3.2.0 / ESP-IDF 5.5.1

GPIO Quick Reference

Function	GPIOs	Notes
E-Paper (SPI2)	DC:10 CS:11 SCK:12 MOSI:13 RST:9 BUSY:8	codes couleur 2 bits : 0x0 noir, 0x1 blanc, 0x2 jaune, 0x3 rouge
Power rails	EPD_PWR:6 (LOW=on) AUDIO_PWR:42 (LOW=on) VBAT_PWR:17 (HIGH=on)	logique inversée sur EPD/audio
Audio I2S (ES8311)	MCLK:14 BCLK:15 LRCK:38 DOUT:45 DIN:16 PA_CTRL:46	speaker : AUDIO_PWR LOW et PA_CTRL HIGH
I2C	SDA:47 SCL:48	PCF85063 0x51, SHTC3 0x70, ES8311 0x18
TF card (SDMMC 1-bit)	CLK:39 CMD:41 D0:40
Battery ADC	GPIO 4	ADC1_CH3, atten 12 dB
Buttons	BOOT:0 PWR:18	BOOT = wakeup deep-sleep dans la démo vendor
LED verte	GPIO 3	active LOW
UART	TX:43 RX:44

Flash (from monorepo root)

./build.sh epaper_154g <ProjectName>            # macOS / Linux
./build.sh epaper_154g <ProjectName> --upload   # + flash

.\build.ps1 epaper_154g <ProjectName>           # Windows
.\build.ps1 epaper_154g <ProjectName> -Upload   # + flash

Progressive Disclosure Index

esp32-platform.md — PlatformIO setup, toolchain, common libraries (reusable across all monorepo devices)
device-hardware.md — Architecture, pinout complet, rails de puissance, chaîne audio, e-paper
resources.md — Wiki, GitHub vendor, demo code local, firmware usine

Mais deste repositório

mesmo repositório

waveshare-esp32

Sandjab/Waveshare-ESP32

Common ESP32-S3 platform reference for all Waveshare devices in this monorepo. Use when working with PlatformIO setup, toolchain, common libraries, or adding a new device.

2026-06-090

waveshare-amoled-175c

Sandjab/Waveshare-ESP32

Development reference for Waveshare ESP32-S3-Touch-AMOLED-1.75C (round 1.75" watch form factor). Use when working with this device, its AMOLED display (CO5300 QSPI 466×466), touch (CST9217), audio (ES8311 playback + ES7210 mic-array AEC), power (AXP2101), IMU (QMI8658), or restoring the factory firmware.

2026-05-170

guition-k718

Sandjab/Waveshare-ESP32

Development reference for Guition JC3636K718 (ESP32-S3, round 1.8" 360×360 + encoder + RGB ring). Use when working with this device, its display (ST77916 QSPI), audio chain (PCM5100A DAC + NS4150B amp), 13× WS2812 ring on GPIO 0, encoder, microphone, DRV2605 + LRA haptics, or restoring the factory firmware.

2026-05-170

waveshare-knob

Sandjab/Waveshare-ESP32

Development reference for Waveshare ESP32-S3-Knob-Touch-LCD-1.8. Use when working with this device, its dual-MCU architecture, display (ST77916 QSPI), touch (CST816), haptics (DRV2605), or audio (PCM5100A).

2026-05-170

waveshare-amoled

Sandjab/Waveshare-ESP32

Development reference for Waveshare ESP32-S3-Touch-AMOLED-1.8. Use when working with this device, its AMOLED display (SH8601 QSPI), touch (FT3168), audio (ES8311), power (AXP2101), IMU (QMI8658), or RTC (PCF85063).

2026-05-170

name	waveshare-epaper-154g
description	Development reference for Waveshare ESP32-S3-ePaper-1.54G (200×200 4-color e-paper, ES8311 audio, SHTC3, PCF85063 RTC, battery). Use when working with this device, its e-paper display (EPD_1in54g driver), power rails, audio codec, sensors, deep-sleep, or restoring the factory firmware.

Waveshare ESP32-S3-ePaper-1.54G

Quick Reference Card

Spec	Value
MCU	ESP32-S3-PICO-1 (LGA56) — Xtensa LX7 dual-core 240 MHz, WiFi + BLE 5
Flash / PSRAM	8 MB Flash (QIO) / 8 MB PSRAM (OPI) — embarquées dans le package, vérifié `esptool flash_id`
Display	1.54" e-paper 200×200, 4 couleurs (noir/blanc/jaune/rouge), SPI, driver vendor `EPD_1in54g`
Refresh	~20 s full, ~15 s fast — UI statique uniquement
Audio	ES8311 codec (I2C 0x18) : speaker MX1.25 (via ampli, ctrl GPIO 46) + micro
Sensors	SHTC3 temp/humidité (I2C 0x70), PCF85063 RTC (I2C 0x51)
Storage	TF card slot (SDMMC 1-bit)
Power	USB-C 5V / Li-ion MX1.25 (ETA6098 charger, VBAT sense ADC GPIO 4)
USB	Type-C, CDC natif exposé par le firmware usine (pas de BOOT dance au 1er flash)
Framework	PlatformIO Arduino (`qio_opi`, 8MB, `default_8MB.csv`) ; vendor : Arduino-ESP32 3.2.0 / ESP-IDF 5.5.1

GPIO Quick Reference

Function	GPIOs	Notes
E-Paper (SPI2)	DC:10 CS:11 SCK:12 MOSI:13 RST:9 BUSY:8	codes couleur 2 bits : 0x0 noir, 0x1 blanc, 0x2 jaune, 0x3 rouge
Power rails	EPD_PWR:6 (LOW=on) AUDIO_PWR:42 (LOW=on) VBAT_PWR:17 (HIGH=on)	logique inversée sur EPD/audio
Audio I2S (ES8311)	MCLK:14 BCLK:15 LRCK:38 DOUT:45 DIN:16 PA_CTRL:46	speaker : AUDIO_PWR LOW et PA_CTRL HIGH
I2C	SDA:47 SCL:48	PCF85063 0x51, SHTC3 0x70, ES8311 0x18
TF card (SDMMC 1-bit)	CLK:39 CMD:41 D0:40
Battery ADC	GPIO 4	ADC1_CH3, atten 12 dB
Buttons	BOOT:0 PWR:18	BOOT = wakeup deep-sleep dans la démo vendor
LED verte	GPIO 3	active LOW
UART	TX:43 RX:44

Flash (from monorepo root)

./build.sh epaper_154g <ProjectName>            # macOS / Linux
./build.sh epaper_154g <ProjectName> --upload   # + flash

.\build.ps1 epaper_154g <ProjectName>           # Windows
.\build.ps1 epaper_154g <ProjectName> -Upload   # + flash

Progressive Disclosure Index

esp32-platform.md — PlatformIO setup, toolchain, common libraries (reusable across all monorepo devices)
device-hardware.md — Architecture, pinout complet, rails de puissance, chaîne audio, e-paper
resources.md — Wiki, GitHub vendor, demo code local, firmware usine