tyutool-cli

name	tyutool/cli
description	Direct tyutool_cli usage for TuyaOpen hardware: list serial ports, flash firmware (write), read flash, hardware reset (DTR/RTS), and authorize devices (UUID/AuthKey via UART). Use when the user mentions tyutool, flashing directly, reading flash, hardware reset, or UART authorization. Tool at $OPEN_SDK_ROOT/tools/tyutool/tyutool_cli (Linux/macOS) or tyutool_cli.exe (Windows). Install: tos.py update -t. 固件烧录、Flash读取、硬件复位、串口设备授权（UUID/AuthKey）。
license	Apache-2.0
compatibility	["TuyaOpen environment activated (export.sh / export.ps1 / export.bat)","tyutool_cli installed at $OPEN_SDK_ROOT/tools/tyutool/ (tos.py update -t)","Device connected via USB serial"]

tyutool CLI

SDK root: All tool paths use $OPEN_SDK_ROOT (Linux/macOS/PowerShell) or %OPEN_SDK_ROOT% (Windows CMD).

Tool Location & Install

Platform	Binary
Linux / macOS	$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli
Windows PowerShell	$env:OPEN_SDK_ROOT\tools\tyutool\tyutool_cli.exe
Windows CMD	%OPEN_SDK_ROOT%\tools\tyutool\tyutool_cli.exe

tos.py update -t   # install or force-update (--tyutool flag)
tos.py update      # also updates tyutool if already installed

$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli --version   # verify

Global Flag: --plain

Always add --plain — disables ANSI/spinner, produces stable parseable output for agents.

Chip Parameters

Three baud rates per chip:

• Flash baud: used by write/read. Recommended rate; higher = faster but risk instability at physical limits. Do not override unless developer instructs; if flash fails with instability, ask developer whether to lower baud.
• Auth baud: used by authorize (default 115200, all chips). Developer may change firmware UART baud — if garbled output during auth, ask developer for correct rate.
• Log baud: used for serial monitor. Developer may change — if garbled monitor output, ask developer for correct rate.

--device	Flash baud	Auth baud	Log baud	Flash size
bk7231n	921600	115200	115200	2 MiB (0x200000)
t2	921600	115200	115200	2 MiB (0x200000)
t3	921600	115200	460800	4 MiB (0x400000)
t1	921600	115200	115200	8 MiB (0x800000)
t5	921600	115200	460800	8 MiB (0x800000)
ln882h	115200	115200	115200	2 MiB (0x200000)
esp32	460800	115200	115200	4 MiB (0x400000)
esp32c3	460800	115200	115200	4 MiB (0x400000)
esp32c6	460800	115200	115200	8 MiB (0x800000)
esp32s3	460800	115200	115200	16 MiB (0x1000000)

Port Selection (Do First)

$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli --plain list-ports

Output (tab-separated): path vid:pid usb_interface port_role display_name

T5/T5AI dual-serial boards (VID 1a86 PID 55d2): two ports per device.

• Flash port (lower enumeration: ttyACM0, lower COM) → write, reset, authorize
• Log port (higher enumeration: ttyACM1, higher COM) → serial monitor / log capture

This mapping is typical but not guaranteed — swap ports if flash fails.

Always pass -p <port> explicitly. Omitting -p with multiple ports triggers an interactive selection prompt (not usable in agent workflows).

write — Flash Firmware

$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli --plain write \
    -d <chip> -f <firmware.bin> -p <flash_port> \
    [-b <baud>] [-s <start_hex>] [--end <end_hex>]

Flag	Required	Default
-d/--device	YES	—
-f/--file	YES	—
-p/--port	NO*	auto-detect
-b/--baud	NO	chip flash baud
-s/--start	NO	0x00000000
--end	NO	start + file size

*Always specify -p for agents.

Success: exit 0, last output line is Flash OK Xs.

read — Dump Flash to File

$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli --plain read \
    -d <chip> -f <output.bin> -p <flash_port> \
    [-s <start_hex>] [-l <length_hex>]

Default length: 0x200000 (2 MiB). For a full dump, use the chip flash size from the table above.

reset — Hardware Reset via DTR/RTS

Use the flash port (same as write).

$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli --plain reset \
    -d <chip> -p <flash_port>

-d default: bk7231n. Reset sequence by family:

• Beken (bk7231n, t1–t5): DTR/RTS pulse
• ESP32 (esp32, esp32c3, esp32c6, esp32s3): espflash hard_reset

authorize — Read/Write UUID + AuthKey

Use the flash port. Operates at the chip's auth baud (115200 by default).

# Read current auth state (omit --uuid and --authkey)
$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli --plain authorize -p <flash_port>

# Write credentials (both flags required together)
$OPEN_SDK_ROOT/tools/tyutool/tyutool_cli --plain authorize \
    -p <flash_port> --uuid <uuid_string> --authkey <authkey_string>

Obtain UUID/AuthKey from the Tuya platform — see skill tuyaopen/device-auth.

Troubleshooting

Symptom	Fix
tyutool_cli: not found	tos.py update -t
No serial ports found	Re-plug USB cable
Handshake fails / timeout	Try the other port
Flash unstable / fails	Ask developer whether to use lower baud (-b 460800)
Garbled output during authorize	Ask developer for firmware's UART auth baud rate
Garbled serial monitor output	Ask developer for firmware's UART log baud rate
Interactive port prompt appears	Always pass -p <port> explicitly

Diagnostic Logs

On failure, check the tool's own log file:

• Linux: ~/.local/share/tyutool/tyutool.log
• macOS: ~/Library/Application Support/tyutool/tyutool.log
• Windows: %APPDATA%\tyutool\tyutool.log