m5-onboard

name	m5-onboard
description	End-to-end onboarding for a freshly-plugged-in M5Stack ESP32 device (Cardputer, Cardputer-Adv, Core, CoreS3, Stick) — detect on USB, flash UIFlow 2.0 firmware, and install the Claude Buddy MicroPython app bundle. Use whenever the user plugs in or wants to flash/provision/reset an M5Stack or ESP32 board, or says "m5-onboard go".

M5Stack Onboarding

This skill automates the full cold-start workflow for an M5Stack ESP32 device: detect on USB, identify model, flash UIFlow 2.0, and push a MicroPython app bundle onto /flash/ so the device boots into user software. The apps we ship (Claude Buddy, Snake, Hello) talk over BLE or USB. The workflow runs on macOS, Linux, and Windows; the skill was developed against an M5Stack Basic v2.6 (CH9102 bridge, ESP32-D0WDQ6-V3, 16 MB flash) and generalized to cover the rest of the Core family, with the Cardputer-Adv (ESP32-S3, native USB) as the current default target.

Where the scripts live

This skill ships as part of the cwc-makers plugin for reference, but the executable scripts and the buddy/ app bundle live in a local clone of https://github.com/moremas/build-with-claude (the /maker-setup command creates this clone). Run every scripts/*.py invocation below from inside that clone's onboard/ directory so --apps buddy resolves to the sibling buddy/device/ payload.

When to use

Use this when a user plugs in an M5Stack device and wants it provisioned. The decision tree:

• Fresh/unknown device → run onboard.py --apps buddy end-to-end (detect → identify → flash → install apps). This is the default path.
• Already-flashed device, user just wants apps installed/refreshed → run install_apps.py --src buddy (or any --src <path> to a directory of .py files).
• Flashed device, something feels broken → run smoke_test.py (I2C + LCD + speaker + button check).
• User wants to know what's on the bus / what the device can do → smoke_test.py.

If multiple devices are plugged in, ask which port to target — don't guess. If the user is provisioning a device they previously worked with (e.g. "same thing as last time" or "another Buddy"), default to --apps buddy unless they say otherwise.

Which variant to assume

The rig this skill lives on provisions Cardputer-Adv boards overwhelmingly, so onboard.py now defaults to --variant cardputer-adv. In practice that means:

• If the user says nothing about the model, go with the default. They're almost certainly holding a Cardputer-Adv.
• If the user says "Cardputer" (no "Adv"), ask — the two models share a form factor but take different firmware images, and flashing the wrong one boot-loops the device.
• If the user names any other board ("Core2", "CoreS3", "Basic", "Fire"), pass the matching --variant explicitly — the default won't apply.
• The chip is ESP32-S3 either way, and detect.py won't be able to tell Cardputer from Cardputer-Adv before UIFlow is flashed (same native USB-JTAG VID, no pre-flash I2C probe). So this is a user-intent question, not a hardware-fingerprint one.

The workflow

The main orchestrator is scripts/onboard.py. It drives the sub-scripts in order and handles the handoffs between them (waiting for reboots, capturing MAC, reporting progress). Prefer calling it directly over stitching the sub-scripts yourself unless the user asks for a partial run.

The default provisioning command (fresh Cardputer-Adv, install the buddy bundle):

python3 scripts/onboard.py --apps buddy

How to invoke this from Claude Code's Bash tool. Do NOT call onboard.py as a foreground Bash command. The Bash tool captures output and does not stream it back to the assistant until the command exits — and this command runs 2–3 minutes. That silence looks identical to a hang, and the assistant will usually give up before the button-dance prompt ever reaches the user. Instead, always run with run_in_background: true, tee to a log file, and then use the Monitor tool (or periodic tail via Read) to surface stage banners, heartbeats, and prompts to the user in real time. 2>&1 is not the fix — all progress already writes to stderr, which a terminal shows fine. The fix is streaming semantics, not redirection. The pattern that works:

# Launch (background, tee log):
python3 scripts/onboard.py --apps buddy 2>&1 | tee /tmp/m5-onboard.log

# Monitor (surfaces key events without drowning in byte-progress spam):
tail -f /tmp/m5-onboard.log | grep -E --line-buffered \
  "^====|heartbeat|Heads up|Enter download mode|download mode!|rebooted into UIFlow|Manual reset|DONE|ERROR|Error|Traceback|FAIL|failed|No USB|not detected|Attempt [0-9]|Device already in download|Download mode port|Post-flash port|Waiting for device"

Relaying physical steps to the user (REQUIRED)

The flash stage cannot proceed without a manual button press on native-USB boards — there is no software path. When the monitored log shows Enter download mode (or the script appears to wait at the FLASH stage), you MUST stop and tell the user to do the following on the back of the Cardputer, in your own words, before continuing:

1. Press and hold the G0 button
2. While still holding G0, briefly press and release the RST button
3. Keep holding G0 for about one more second, then release it
4. The screen should go fully dark — that means download mode is active

If the device reboots into UIFlow instead of going dark, tell the user G0 was released too early and to try again holding it longer. Do not move on, retry the script, or attempt a software workaround until the user confirms the screen is dark — the flash will not start otherwise. The same applies to any later Manual reset prompt: relay the physical step and wait for the user.

Users running onboard.py directly in their own terminal (not via Claude Code) will see all output live — no changes needed there.

If --port is omitted, detect.py picks the most likely candidate across all three OSes: native-USB ESP32-S3 (/dev/cu.usbmodem* on macOS, /dev/ttyACM* on Linux, COMx on Windows), or a CH9102/CP210x UART bridge on older boards. Bluetooth-serial ports are filtered out. If multiple candidates are present, it asks.

The known apps name buddy resolves to the buddy/device/ directory in this repo (custom launcher + Hello + Claude Buddy BLE client + Snake). Any other --apps value is treated as a filesystem path.

To skip re-flashing and just push (or refresh) the apps onto an already-provisioned device:

python3 scripts/install_apps.py --port <PORT> --src buddy

Where <PORT> is whatever detect.py printed on the last full run — for example /dev/cu.usbmodem1101, /dev/ttyACM0, or COM3.

Stages

1. Detect (detect.py) — enumerate serial ports, filter to USB-UART bridges (CH9102 vendor 0x1A86, Silabs CP210x 0x10C4, FTDI 0x0403) or the ESP32-S3 native USB-JTAG interface (0x303A). Probe with esptool to confirm the chip. Port names differ per OS (/dev/cu.usbmodem* on macOS, /dev/ttyACM*/ttyUSB* on Linux, COMx on Windows) but pyserial abstracts that.
2. Identify (detect.py) — alongside port discovery, detect.py reads the factory-test partition signature and/or scans I2C once UIFlow is on, and cross-references references/hardware_signatures.md to suggest the right firmware variant (Basic-16MB, Core2, CoreS3, Cardputer-Adv, etc.). User-facing variant choice happens via onboard.py --variant; there is no separate detect.py --identify flag.
3. Fetch firmware (fetch_firmware.py) — query the M5Burner manifest API and download the appropriate UIFlow 2.0 binary into the system temp dir. Cached between runs — safe to clear the cache anytime, it just re-downloads.
4. Flash (flash.py) — esptool write_flash 0x0 <image> at 460800 baud for UART bridges, --no-stub at 115200 baud for native-USB S3 devices. 921600 fails intermittently on the CH9102 bridge — do not increase it. Native-USB flash can intermittently throw Lost connection, retrying mid-erase; esptool recovers. The post-flash watchdog-reset teardown step can fail even when the flash itself succeeded — flash.py parses esptool's stdout, treats that specific failure pattern as non-fatal when Hash of data verified appeared, and onboard.py falls back to flash.native_reset() and then manual-RESET coaching if needed.
5. Install apps (optional, install_apps.py) — paste-mode REPL upload of every .py from a source directory into /flash/, then reboot via repl_reset (DTR/RTS is a no-op on native USB — don't reach for it). Source layout: root *.py → /flash/, apps/*.py → /flash/apps/ (UIFlow's stock launcher scans that). When the bundle ships a root , also sets NVS so UIFlow's own launcher doesn't run and our takes over the boot flow — critical for BLE-using apps on ESP32-S3 (see gotchas below).

Critical gotchas (baked into the scripts — do not second-guess)

These are things the scripts already handle correctly but which you should not override if the user asks you to "just run esptool manually" or similar:

• Native-USB ESP32-S3 boards (Cardputer, Cardputer-Adv, CoreS3) require a physical BtnG0+BtnRST dance to enter download mode. There is no software path. The chip has no DTR/RTS bridge, so nothing esptool or pyserial can do will put it into the ROM bootloader — the user has to hold GPIO0 low across a reset pulse with the hardware buttons. On Cardputer-Adv specifically both buttons (BtnG0 and BtnRST) are on the back of the device — small, flush-mounted, often easiest to press with a fingernail. onboard.py:_wait_for_download_port prompts for this at runtime during FLASH: press and HOLD BtnG0, briefly press BtnRST, release BtnRST first, keep holding BtnG0 for ~1 more second, release BtnG0, screen should be fully dark. If the device reboots back into UIFlow instead, BtnG0 was released too early — the coaching retries and tells the user to hold it longer. Do NOT try to automate this with esptool --before default_reset or pyserial's DTR/RTS; both are no-ops on native USB (the pins aren't wired to EN), and adding them just hides the real prompt.
• Do not unplug the device during FLASH. Especially on native USB. A mid-flash disconnect leaves the internal flash in an inconsistent state. Mask ROM is usually reachable afterwards (press BtnG0 alone on the back, or do the full BtnG0+BtnRST dance), so the recovery is just to re-run m5-onboard go — it's idempotent and will re-enter download mode, re-flash, re-push apps. Don't panic and don't start opening the case; the mask ROM is in silicon and survives a corrupted flash as long as the USB PHY is intact.
• Baud rate is 460800 on UART bridges, 115200 with --no-stub on native USB. Not 921600 on either. The CH9102 bridge loses sync on erase_flash at 921600 (not theoretical — it fails). Native USB's stub-baud-bump path produces "Lost connection" mid-flash; 115200 no-stub is counterintuitively faster end-to-end because it never fails.
• NVS writes must use set_str, not set_blob (relevant to install_apps.py's boot_option setter). UIFlow's startup calls nvs.get_str() and ESP-IDF tags blob and string entries separately. A blob-tagged key returns ESP_ERR_NVS_NOT_FOUND to get_str, and the device boot-loops. If a prior attempt wrote a blob, call nvs.erase_key(name) before set_str.
• REPL multi-line blocks need paste mode. Sending try:/except: line-by-line makes the REPL accumulate indentation forever. Use Ctrl-E to enter paste mode, send the block, Ctrl-D to execute. wraps this.

After provisioning (what the user sees on the device)

Once m5-onboard go finishes at the DONE banner, the device is ready to use on its own:

• Power. Slide the switch on the right edge of the Cardputer-Adv to turn it on. Same switch turns it off. The board runs off its internal LiPo when unplugged; USB-C charges it.
• Boot. A short boot log scrolls, then the launcher menu appears automatically. The menu lists every .py in /flash/apps/ plus the top-level /flash/*.py entries.
• Navigation. Arrow keys (or the keyboard's trackpoint-style cursor keys) scroll the menu; Enter launches the highlighted app; ESC returns to the launcher from inside an app.
• Event WiFi auto-connect. The bundle's main.py connects to a hard-coded event WiFi (SSID cardputer) on every boot and shows the result on the LCD before the launcher menu appears. Credentials live in buddy/device/wifi_event.py; the connect is best-effort and the launcher always continues even if the connect fails. If you're using this bundle outside the event, edit wifi_event.py or remove the _connect_wifi_with_splash() call from main.py.
• Claude Buddy over BLE. First time only: in Claude Desktop, Help → Troubleshooting → Enable Developer Tools (one-time, persists across launches). Then Developer menu → Hardware Buddy → Connect. BLE works regardless of the WiFi state — the link to Claude.app is local.
• Getting back to UIFlow. The buddy bundle ships only a main.py at /flash/ (no replacement boot.py), so the stock UIFlow boot.py is never touched and there's no boot_uiflow.py backup to restore. Revert by removing our main.py from the device REPL: os.remove('/flash/main.py') followed by machine.reset(). UIFlow's stock launcher takes over on the next boot. To start completely fresh including the firmware, re-run the skill without --apps.

Files

• scripts/onboard.py — main orchestrator
• scripts/detect.py — port discovery + chip ID
• scripts/fetch_firmware.py — M5Burner API + download
• scripts/flash.py — esptool wrapper
• scripts/install_apps.py — push a directory of .py files into /flash/ via paste-mode REPL; backs up boot.py as boot_uiflow.py before overwriting; also writes the boot_option NVS key when the bundle ships a root main.py
• scripts/smoke_test.py — I2C + LCD + speaker + buttons
• scripts/mpy_repl.py — shared serial/REPL helpers (paste mode, hard reset, boot-log capture)
• references/hardware_signatures.md — chip + I2C fingerprints → model → firmware
• references/uiflow2_nvs.md — NVS key reference with types and failure modes

Dependencies

• pyserial — vendored at onboard/scripts/vendor/serial/ (pinned 3.5, BSD-3-Clause).
• esptool — pip dependency, declared in requirements.txt. Importable check happens via importlib.util.find_spec("esptool"); binary backstop search covers ~/Library/Python/*/bin/ on macOS, ~/.local/bin/ on Linux, %APPDATA%\Python\Python3XX\Scripts\ on Windows.

onboard.py runs a preflight check at startup: if esptool (or, in the rare prune-vendor case, pyserial) is missing, it lists what's needed and asks the user whether to install now. On Y (or Enter) it runs python -m pip install --user <missing> in the current interpreter, then verifies. Inside a venv the --user flag is dropped so the install lands in the venv's site-packages. Non-interactive callers (piped stdin) get a manual-install hint instead of a prompt.

Python itself has to exist before this skill can do anything — you can't bootstrap an interpreter from inside one. git is not required — the /maker-setup command falls back to downloading the GitHub tarball with curl+tar (both pre-installed on macOS, Linux, and Windows 10+) when git --version fails. Claude's responsible for detecting Python and installing it if missing before running any scripts/*.py invocation. Detection is just running python3 --version / python --version — if it fails, Claude fetches Python with the host's native package manager before anything else.

Per-OS Python bootstrap (Claude's responsibility if missing):

• Windows — winget install -e --id Python.Python.3.13 --silent --accept-source-agreements --accept-package-agreements. Takes ~30 seconds, no UI, gets PATH right. If the current shell can't see python afterwards, tell the user to close and reopen the terminal (Windows updates PATH only on new shells).
• macOS — Python 3 is usually pre-installed as /usr/bin/python3 on any current macOS (shipped by Apple). If for some reason it isn't, brew install python@3.13 via Homebrew is the go-to; if Homebrew itself is missing, offer to install it via /bin/bash -c "$(curl -fsSL https://raw.githubusercontent.com/Homebrew/install/HEAD/install.sh)" (but only if the user confirms — Homebrew is a larger commitment than winget).
• Linux — use the distro package manager. Debian/Ubuntu: sudo apt-get update && sudo apt-get install -y python3 python3-pip. Fedora: sudo dnf install -y python3 python3-pip. Arch: sudo pacman -S --noconfirm python python-pip. You may need to sudo and should surface the password prompt to the user if needed.

pyserial — bundled with the skill:

A pinned pyserial 3.5 ships under scripts/vendor/ (BSD-3-Clause, Apache-compatible). Every script that imports serial calls vendor_path.ensure_on_syspath() before the first third-party import, which prepends scripts/vendor/ to sys.path, so the vendored copy resolves regardless of whatever the user has system-wide. Net effect: port enumeration and REPL I/O work on a fresh clone with zero pip step. ~500 KB, pure-Python, same tree on macOS / Linux / Windows.

esptool — pip dependency, auto-installed on first run:

esptool is GPLv2+ and is intentionally not vendored — keeping the repository cleanly Apache-2.0 means the GPL bits live in the user's pip-managed environment, not in the tree. The skill's preflight checks for an importable esptool and, if missing, prompts to install it (python -m pip install --user esptool — --user dropped inside a venv so it lands in site-packages). For subprocess calls we use [sys.executable, "-m", "esptool", ...]; the subprocess inherits user-site so the pip-installed module imports cleanly. requirements.txt declares this for explicit setup; the prompt path is the default for first-time attendees who haven't run pip yet.

Non-interactive callers (piped stdin, CI) skip the prompt and get a python -m pip install --user esptool hint instead.

Fallback if someone prunes scripts/vendor/:

The same preflight path also re-installs pyserial via pip if the vendor copy is gone. This handles the case where someone downloaded a source-only zip that excluded vendor, or manually trimmed the repo to save space.

USB driver — Windows-specific, only for older boards:

The CH9102 USB-UART driver is still a manual install on Windows — WCH doesn't publish a winget manifest. Only needed for UART-bridge boards (Basic, Fire, Core2, StickC). Native-USB ESP32-S3 boards (Cardputer, Cardputer-Adv, CoreS3) enumerate as composite USB-CDC devices using Windows' in-box drivers and need no extra install.

Platform notes

The skill runs on macOS, Linux, and Windows. Non-obvious bits:

• Port naming. pyserial abstracts the lookup but what the user sees looks different per OS. Pass whichever form detect.py reports:

  • macOS: /dev/cu.usbmodem1101 (native USB) or /dev/cu.usbserial-XXXX (CH9102)
  • Linux: /dev/ttyACM0 (native USB) or /dev/ttyUSB0 (UART bridge)
  • Windows: COM3, COM4, etc. (Device Manager → Ports if unsure)

• Linux permissions — read this before blaming hardware. On most distros, accessing /dev/ttyUSB* / /dev/ttyACM* without sudo requires group membership (dialout on Debian/Ubuntu/Arch, uucp on Fedora). Symptom: detect.py finds the port, but the flash step fails with Permission denied or Could not open port. Fix once, long-term:

  sudo usermod -aG dialout $USER
  # log out / log back in — group change only takes effect for new sessions
  

  sudo python3 scripts/onboard.py ... works as a one-off but adding the group membership is strictly better because pyserial's port-open in user mode succeeds cleanly from then on.

• Windows PATH gotchas. Python's pip install --user esptool lands the executable in %APPDATA%\Python\Python3XX\Scripts\. If that directory isn't on PATH, pip prints a warning and nothing else picks up the install. detect.py looks there directly as a backstop, so the skill still works even without PATH fixed. But if you're invoking esptool outside the skill (or hitting "esptool not found" errors from other tools), either:

  • Re-run the Python installer and tick "Add Python to PATH" (the install's default), OR
  • Add %APPDATA%\Python\Python3XX\Scripts to PATH via System Properties → Environment Variables, OR
  • Use python -m esptool ... which always works regardless of PATH.

• Windows Store Python. Newer Windows 11 machines may have Python pre-installed via Microsoft Store. It works but has quirky PATH behavior (lives under %LOCALAPPDATA%\Packages\PythonSoftwareFoundation.Python.*\). checks that location too. If you have the choice, the version is more predictable.