| name | ESP32-S3 PIE SIMD Optimization |
| description | ESP32-S3 Processor Instruction Extensions (PIE) SIMD reference for accelerating C code. Use when converting scalar C loops into PIE SIMD assembly (EE.* instructions). Covers 128-bit QR registers, vector arithmetic, MAC, non-aligned data, FFT, and common patterns. Target chip: ESP32-S3 (Xtensa LX7 with TIE extensions).
|
ESP32-S3 PIE SIMD Quick Reference
REGISTERS
General Purpose
| Register | Count | Width | Use |
|---|
| AR (a0-a15) | 16 | 32-bit | Address/data, a1=sp, a2-a7=args, a8-a15=addr operands |
| QR (q0-q7) | 8 | 128-bit | SIMD vectors: 16×8-bit, 8×16-bit, or 4×32-bit lanes |
| FR (f0-f15) | 16 | 32-bit | IEEE754 float |
Special Registers (PIE-specific)
| Register | Width | Access via | Purpose |
|---|
| SAR | 6-bit | RSR/WUR.SAR | Mul result right-shift amount (bits) |
| SAR_BYTE | 4-bit | RUR/WUR.SAR_BYTE | Byte shift amount for SRC.Q |
| ACCX | 40-bit | RUR/WUR ACCX_0,ACCX_1 | Scalar accumulator (sum of all lane products) |
| QACC_H | 160-bit | RUR/WUR QACC_H_0..4 | Per-lane accumulator high (8×20-bit or 4×40-bit) |
| QACC_L | 160-bit | RUR/WUR QACC_L_0..4 | Per-lane accumulator low |
| FFT_BIT_WIDTH | 4-bit | WUR.FFT_BIT_WIDTH | Bit-reversal width (0→3bit ... 7→10bit) |
| UA_STATE | 128-bit | RUR/WUR UA_STATE | Unaligned load persistent state |
Special Register Access
WSR.SAR aN ; write SAR
RSR.SAR aN ; read SAR
XSR.SAR aN ; exchange AR and SAR
WUR.ACCX_0 aN ; write ACCX[31:0]
WUR.ACCX_1 aN ; write ACCX[39:32] (lower 8 bits of aN used)
RUR.ACCX_0 aN ; read ACCX[31:0]
RUR.ACCX_1 aN ; read ACCX[39:32] → aN[7:0]
WUR.SAR_BYTE aN ; write SAR_BYTE
RUR.SAR_BYTE aN ; read SAR_BYTE
WUR.QACC_H_0 aN ; write QACC_H segment 0 (bits 31:0)
RUR.QACC_H_0 aN ; read QACC_H segment 0 (bits 31:0)
; QACC_H segments: _0(31:0) _1(63:32) _2(95:64) _3(127:96) _4(159:128)
; QACC_L same segment layout
EE.ZERO.ACCX ; ACCX = 0
EE.ZERO.QACC ; QACC_H = 0, QACC_L = 0
EE.ZERO.Q qN ; qN = 0
ALIGNMENT RULES (CRITICAL)
PIE loads/stores force address low bits to 0:
- 128-bit access: low 4 bits forced to 0 (16-byte aligned)
- 64-bit access: low 3 bits forced to 0 (8-byte aligned)
- 32-bit access: low 2 bits forced to 0 (4-byte aligned)
- 16-bit access: low 1 bit forced to 0 (2-byte aligned)
Always declare buffers with __attribute__((aligned(16))) or use heap_caps_aligned_alloc(16, size, MALLOC_CAP_DEFAULT).
Unaligned Load Pattern (3 instructions)
EE.LD.128.USAR.IP q0, aN, 16 ; load aligned chunk, save offset→SAR_BYTE, aN+=16
EE.VLD.128.IP q1, aN, 16 ; load next aligned chunk, aN+=16
EE.SRC.Q q2, q0, q1 ; {q1,q0} >> SAR_BYTE*8 → q2 (lower 128 bits)
INSTRUCTION CLASSIFICATION BY OPERATION
1. LOAD (Memory → QR / QACC)
EE.VLD.128.IP qu, as, imm16 ; qu=load128(aligned(as)), as+=sext(imm16)*16
EE.VLD.128.XP qu, as, ad ; qu=load128(aligned(as)), as+=ad
EE.LD.128.USAR.IP qu, as, imm16 ; SAR_BYTE=as[3:0], qu=load128(aligned(as)), as+=sext(imm16)*16
EE.LD.128.USAR.XP qu, as, ad ; SAR_BYTE=as[3:0], qu=load128(aligned(as)), as+=ad
EE.VLD.H.64.IP qu, as, imm8 ; qu[127:64]=load64(aligned(as)), as+=sext(imm8)*8
EE.VLD.L.64.IP qu, as, imm8 ; qu[63:0]=load64(aligned(as)), as+=sext(imm8)*8
EE.VLDBC.8 qu, as ; qu = broadcast(load8(as)), as += 1
EE.VLDBC.8.IP qu, as, imm1 ; qu = broadcast(load8(as)), as += imm1 (0..1)
EE.VLDBC.16 qu, as ; qu = broadcast(load16(aligned(as))), as += 2
EE.VLDBC.32 qu, as ; qu = broadcast(load32(aligned(as))), as += 4
EE.LDQA.S8.128.IP as, imm16 ; sign-extend 16×8bit→16×20bit into QACC_H+L, as+=sext(imm16)*16
EE.LDQA.S16.128.IP as, imm16 ; sign-extend 8×16bit→8×40bit into QACC_H+L, as+=sext(imm16)*16
EE.LDQA.U8.128.IP as, imm16 ; zero-extend 16×8bit→16×20bit into QACC_H+L, as+=sext(imm16)*16
EE.LDQA.U16.128.IP as, imm16 ; zero-extend 8×16bit→8×40bit into QACC_H+L, as+=sext(imm16)*16
; IP = Immediate Post-increment, XP = register post-increment
; VLD.128.IP: step = sext(imm16)*16, range -512..496 (6-bit immediate)
; VST.128.IP: step = sext(imm8)*16, range -2048..2032 (8-bit immediate)
; VLD.H/L.64.IP: step = sext(imm8)*8, range -1024..1016
2. STORE (QR → Memory)
EE.VST.128.IP qv, as, imm16 ; store128(qv, aligned(as)), as+=sext(imm8)*16
EE.VST.128.XP qv, as, ad ; store128(qv, aligned(as)), as+=ad
EE.VST.H.64.IP qv, as, imm8 ; store64(qv[127:64], aligned(as)), as+=sext(imm8)*8
EE.VST.L.64.IP qv, as, imm8 ; store64(qv[63:0], aligned(as)), as+=sext(imm8)*8
3. VECTOR ARITHMETIC (lane-wise, saturated)
EE.VADDS.S8 qa, qx, qy ; qa[i]=saturate_s8(qx[i]+qy[i]) for i in 0..15
EE.VADDS.S16 qa, qx, qy ; qa[i]=saturate_s16(qx[i]+qy[i]) for i in 0..7
EE.VADDS.S32 qa, qx, qy ; qa[i]=saturate_s32(qx[i]+qy[i]) for i in 0..3
EE.VSUBS.S8 qa, qx, qy ; qa[i]=saturate_s8(qx[i]-qy[i])
EE.VSUBS.S16 qa, qx, qy ; qa[i]=saturate_s16(qx[i]-qy[i])
EE.VSUBS.S32 qa, qx, qy ; qa[i]=saturate_s32(qx[i]-qy[i])
; Combined Load+Arithmetic (qu=load result, qa=arithmetic result)
EE.VADDS.S8.LD.INCP qu, as, qa, qx, qy ; as+=16
EE.VADDS.S16.LD.INCP qu, as, qa, qx, qy ; as+=16
EE.VADDS.S32.LD.INCP qu, as, qa, qx, qy ; as+=16
; Combined Store+Arithmetic (store qv, compute qa)
EE.VADDS.S8.ST.INCP qv, as, qa, qx, qy ; store qv→aligned(as), as+=16
4. VECTOR MULTIPLY (lane-wise, SAR right-shift)
EE.VMUL.S8 qz, qx, qy ; qz[i]=(s8*qx[i] * s8*qy[i]) >> SAR[5:0] for i=0..15
EE.VMUL.S16 qz, qx, qy ; qz[i]=(s16*qx[i] * s16*qy[i]) >> SAR[5:0] for i=0..7
EE.VMUL.U8 qz, qx, qy ; unsigned variant
EE.VMUL.U16 qz, qx, qy ; unsigned variant
; SET SAR BEFORE MULTIPLY:
; movi aN, shift_amount
; wsr.sar aN
5. COMPLEX MULTIPLY (16-bit, 4 complex pairs × selected qy half)
EE.CMUL.S16 qz, qx, qy, sel4
; sel4 selects one 32-bit complex number from qy:
; temp[31:0] = qy[sel4*32+31:sel4*32]
; For each of the 4 complex pairs in qx (i=0..3):
; qz[64*i+15:64*i] = qx[64*i+15:64*i] * temp[15:0] - qx[64*i+31:64*i+16] * temp[31:16]
; qz[64*i+31:64*i+16] = qx[64*i+15:64*i] * temp[31:16] + qx[64*i+31:64*i+16] * temp[15:0]
; All results right-shifted by SAR. All 4 complex pairs multiply with the
; same selected temp value (not pairwise with corresponding qy elements).
6. MULTIPLY-ACCUMULATE
ACCX mode (scalar sum of all lane products):
EE.VMULAS.S8.ACCX qx, qy ; ACCX += Σ(qx[i] * qy[i]) for i=0..15, saturated to 40-bit
EE.VMULAS.S16.ACCX qx, qy ; ACCX += Σ(qx[i] * qy[i]) for i=0..7
EE.VMULAS.U8.ACCX qx, qy ; unsigned
EE.VMULAS.U16.ACCX qx, qy ; unsigned
; Read raw result: RUR.ACCX_0 aN (low 32), RUR.ACCX_1 aN (high 8)
EE.SRS.ACCX rd, rs, 0 ; arithmetic right shift ACCX by rs[5:0], write back to ACCX
; and write saturated 32-bit signed result to rd
; rd = min(max(ACCX>>rs[5:0], -2^31), 2^31-1)
QACC mode (per-lane accumulation, 20-bit or 40-bit per lane):
EE.VMULAS.S8.QACC qx, qy ; QACC[i] += qx[i]*qy[i], 20-bit signed saturated per lane
EE.VMULAS.S16.QACC qx, qy ; QACC[i] += qx[i]*qy[i], 40-bit signed saturated per lane
EE.VMULAS.U8.QACC qx, qy ; unsigned
EE.VMULAS.U16.QACC qx, qy ; unsigned
; Extract QACC→QR with right-shift+sat (shift amount from as register, NOT SAR):
EE.SRCMB.S8.QACC qu, as, 0 ; 16×20-bit→16×8-bit, R-shift by as[4:0], saturate to s8→qu
EE.SRCMB.S16.QACC qu, as, 0 ; 8×40-bit→8×16-bit, R-shift by as[5:0], saturate to s16→qu
; QACC values are also updated with the shifted results (read-modify-write)
7. COMPARISON (result = 0xFF on true, 0 on false)
EE.VMAX.S8 / S16 / S32 qa, qx, qy ; qa[i] = max(qx[i], qy[i])
EE.VMIN.S8 / S16 / S32 qa, qx, qy ; qa[i] = min(qx[i], qy[i])
EE.VCMP.EQ.S8 qa, qx, qy ; qa[i] = (qx[i]==qy[i]) ? 0xFF : 0
EE.VCMP.LT.S8 qa, qx, qy ; qa[i] = (qx[i] < qy[i]) ? 0xFF : 0
EE.VCMP.GT.S8 qa, qx, qy ; qa[i] = (qx[i] > qy[i]) ? 0xFF : 0
; Use ANDQ with mask to implement conditional selection (e.g. ReLU)
8. BITWISE
EE.ANDQ qa, qx, qy ; qa = qx & qy (128-bit)
EE.ORQ qa, qx, qy ; qa = qx | qy
EE.XORQ qa, qx, qy ; qa = qx ^ qy
EE.NOTQ qa, qx ; qa = ~qx
9. SHIFT
EE.VSL.32 qa, qs ; qa[i] = qs[i] << SAR[5:0] (4×32-bit logical left)
EE.VSR.32 qa, qs ; qa[i] = qs[i] >> SAR[5:0] (4×32-bit arithmetic right)
EE.SRC.Q qa, qs0, qs1 ; qa = ({qs1,qs0} >> SAR_BYTE*8)[127:0]
; SRC.Q used with LD.128.USAR for unaligned access
10. DATA MOVEMENT
MV.QR qu, qs ; qu = qs
EE.ZERO.Q qa ; qa = 0
EE.MOVI.32.A qs, au, sel4 ; au = qs[sel4*32+31:sel4*32] (extract 32-bit lane)
EE.MOVI.32.Q qu, as, sel4 ; qu[sel4*32+31:sel4*32] = as (insert 32-bit lane)
EE.MOV.S8.QACC qs ; sign-extend 16×8bit→16×20bit to QACC_H+L
EE.MOV.S16.QACC qs ; sign-extend 8×16bit→8×40bit to QACC_H+L
EE.MOV.U8.QACC qs ; zero-extend 16×8bit→16×20bit to QACC_H+L
EE.MOV.U16.QACC qs ; zero-extend 8×16bit→8×40bit to QACC_H+L
11. ACTIVATION
EE.VRELU.S8 qs, ax, ay ; qs[i] = (qs[i]<=0) ? (qs[i]*ax[7:0])>>ay[4:0] : qs[i]
EE.VRELU.S16 qs, ax, ay ; qs[i] = (qs[i]<=0) ? (qs[i]*ax[15:0])>>ay[5:0] : qs[i]
EE.VPRELU.S8 qz, qx, qy, ay ; qz[i]=(qx[i]<=0) ? (qx[i]*qy[i])>>ay[4:0] : qx[i]
EE.VPRELU.S16 qz, qx, qy, ay ; qz[i]=(qx[i]<=0) ? (qx[i]*qy[i])>>ay[5:0] : qx[i]
12. ZIP/UNZIP (interleave/deinterleave)
EE.VZIP.8 / 16 / 32 qs0, qs1 ; interleave qs0 and qs1 elements in-place
EE.VUNZIP.8 / 16 / 32 qs0, qs1 ; deinterleave qs0 and qs1 elements in-place
13. FFT-SPECIFIC
EE.FFT.R2BF.S16 qa0, qa1, qx, qy, sel2 ; radix-2 butterfly
EE.FFT.R2BF.S16.ST.INCP qa0, qx, qy, as, sar4 ; butterfly + store sums
EE.FFT.CMUL.S16.LD.XP qu, as, ad, qz, qx, qy, sel8 ; complex mul + load
EE.FFT.CMUL.S16.ST.XP qx, qy, qv, as, ad, sel8, upd4, sar4 ; complex mul + store
EE.FFT.AMS.S16.LD.INCP qu, as, qz, qz1, qx, qy, qm, sel2 ; FFT AMS + load
EE.FFT.AMS.S16.LD.INCP.UAUP qu, as, qz, qz1, qx, qy, qm, sel2 ; AMS+unaligned load
EE.FFT.AMS.S16.LD.R32.DECP qu, as, qz, qz1, qx, qy, qm, sel2 ; AMS+reversed32 load
EE.FFT.AMS.S16.ST.INCP qv, qz1, at, as, qx, qy, qm, sel2 ; AMS + store
EE.FFT.VST.R32.DECP qv, as, sar2 ; reversed32 store, as-=16
EE.BITREV qa, as ; bit-reverse (needs FFT_BIT_WIDTH)
14. GPIO
EE.WR_MASK_GPIO_OUT as, ax ; GPIO_OUT[7:0] = (GPIO_OUT & ~ax[7:0]) | (as[7:0] & ax[7:0])
EE.SET_BIT_GPIO_OUT imm8 ; GPIO_OUT[imm8] = 1
EE.CLR_BIT_GPIO_OUT imm8 ; GPIO_OUT[imm8] = 0
EE.GET_GPIO_IN au ; au[7:0] = GPIO_IN[7:0]
C → PIE SIMD CONVERSION PATTERNS
Pattern A: Element-wise Arithmetic (Add/Sub/Mul)
→
; a2=out, a3=in0, a4=in1, a5=N
srai a5, a5, 3 ; N/8 (8 elements per 128-bit load)
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16 ; load 8×int16_t
ee.vld.128.ip q1, a4, 16
ee.vadds.s16 q2, q0, q1 ; 8 lane adds with saturation
ee.vst.128.ip q2, a2, 16
0:
Pattern B: Dot Product (Reduce Sum)
→
; Use ACCX for scalar accumulation
ee.zero.accx
srai a4, a4, 4 ; N/16 (16 elements per load)
loopgtz a4, 0f
ee.vld.128.ip q0, a2, 16
ee.vld.128.ip q1, a3, 16
ee.vmulas.s8.accx q0, q1 ; ACCX += Σall_lanes(q0[i]*q1[i])
0:
rur.accx_0 a2 ; result low 32
rur.accx_1 a3 ; result high 8
Pattern C: Multiply with Scale (Weighted Sum)
→
movi a6, shift_amount
wsr.sar a6 ; SAR controls right-shift
srai a5, a5, 3
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16
ee.vld.128.ip q1, a4, 16
ee.vmul.s16 q2, q0, q1 ; multiply, >>SAR
ee.vst.128.ip q2, a2, 16
0:
Pattern D: Multiply-Accumulate per Lane (e.g. Quantized Conv)
→
; Use QACC for per-lane accumulation
ee.zero.qacc
movi a6, shift_amount ; shift for SRCMB (not SAR!)
srai a5, a5, 4 ; 16×int8 per load
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16
ee.vld.128.ip q1, a4, 16
ee.vmulas.s8.qacc q0, q1 ; QACC[i] += q0[i]*q1[i] for i=0..15
0:
ee.srcmb.s8.qacc q2, a6, 0 ; extract: 20-bit→8-bit with >>a6[4:0], saturate
Pattern E: ReLU Activation
→
; Use VMAX with zero: max(x, 0) = ReLU (VCMP.GT only has S8, no S16 variant)
ee.zero.q q3 ; zeros vector
srai a5, a5, 3
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16
ee.vmax.s16 q2, q0, q3 ; q2[i] = max(q0[i], 0)
ee.vst.128.ip q2, a2, 16
0:
Alternative using VRELU (faster, fewer ops):
; EE.VRELU.S16 qs, ax, ay: if qs[i]<=0 then qs[i]=(qs[i]*ax)>>ay else qs[i]=qs[i]
; For standard ReLU: ax=0 (multiply by 0), ay=0 (shift 0)
movi a6, 0
srai a5, a5, 3
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16
ee.vrelu.s16 q0, a6, a6 ; in-place ReLU: negative→0
ee.vst.128.ip q0, a2, 16
0:
Pattern F: PReLU / LeakyReLU
→
; Load slope once, broadcast to all lanes
ee.vldbc.16 q3, a5 ; broadcast slope to 8 lanes
srai a6, a6, 3
loopgtz a6, 0f
ee.vld.128.ip q0, a3, 16
ee.vprelu.s16 q2, q0, q3, a7 ; q2[i]=(q0[i]<=0)?(q0[i]*q3[i])>>a7:q0[i]
ee.vst.128.ip q2, a2, 16
0:
Pattern G: Loop with Unaligned Load
→
ee.ld.128.usar.ip q0, a3, 16 ; first unaligned load, offset→SAR_BYTE
ee.vld.128.ip q1, a3, 16 ; second aligned load
srai a5, a5, 3
addi a5, a5, -1 ; one iteration already consumed
loopgtz a5, 0f
ee.src.q q2, q0, q1 ; align: q2 = ({q1,q0}>>SAR_BYTE*8)[127:0]
ee.vld.128.ip q0, a3, 16 ; next aligned chunk
; ... process q2 ...
; swap q0↔q1 for next iteration:
ee.src.q q2, q1, q0 ; use the newly loaded data
ee.vld.128.ip q1, a3, 16
; ... process q2 ...
0:
Pattern H: Bias Addition (broadcast scalar to vector)
→
ee.vldbc.16 q3, a4 ; broadcast bias to all 8 lanes
srai a5, a5, 3
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16
ee.vadds.s16 q2, q0, q3
ee.vst.128.ip q2, a2, 16
0:
Pattern I: Max Pooling (2x1)
→
srai a5, a5, 4 ; output has N/8 elements, input has N/4
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16 ; load 8 pairs = 16 elements
ee.vld.128.ip q1, a3, 16
; Use VUNZIP to separate evens and odds, then VMAX
ee.vunzip.16 q0, q1 ; q0=evens, q1=odds
ee.vmax.s16 q2, q0, q1
ee.vst.128.ip q2, a2, 16
0:
LOOP STRUCTURES
Label Naming Convention (REQUIRED)
For branch/loop targets, use local labels: either a plain number (0:, 1:, referenced as 0f/0b) or a .L-prefixed name (.Lloop, .Lremainder). Do not use full descriptive labels like loop_start: / end_label:.
- Numeric local labels keep tight inner loops compact and avoid name clashes.
.L labels stay local to the file (not emitted into the symbol table) and clearly mark internal jump targets.
; GOOD — numeric local label
loopgtz a6, 0f
ee.vadds.s16.ld.incp q0, a3, q2, q0, q1
ee.vld.128.ip q1, a4, 16
ee.vst.128.ip q2, a2, 16
0:
; GOOD — .L local label
bgez a9, .Lleft_shift
.Lright_shift_loop:
; ...
bnez a5, .Lright_shift_loop
.Lleft_shift:
; BAD — full descriptive global-style labels
right_shift_loop:
; ...
bnez a5, right_shift_loop
Zero-Overhead Loop (preferred)
; LOOPGTZ: enter loop body if aN > 0; decrements LCOUNT each iteration
srai a5, a5, 3 ; convert element count to iteration count
loopgtz a5, 0f
; ... loop body (max ~56 instructions) ...
0:
Manual Loop (when zero-overhead loop constraints violated)
srai a5, a5, 3
beqz a5, 1f
.Lloop:
; ... loop body ...
addi a5, a5, -1
bnez a5, .Lloop
1:
PIPELINE & SCHEDULING
Data Dependencies (insert NOPs or reorder to avoid stalls)
- QR load → use: 2 cycle latency (result ready in W stage, used in R stage)
- QR multiply → use: result ready in E stage (same as arithmetic), 0-1 cycle
- SAR write → use: requires ISYNC or at least 1 instruction gap
Prefer LD+OP fused instructions when available
Instead of separate load + compute:
; Sub-optimal: 3 instructions
ee.vld.128.ip q0, a3, 16
ee.vld.128.ip q1, a4, 16
ee.vadds.s16 q2, q0, q1
; Optimal when loading new data for next iteration:
ee.vadds.s16.ld.incp q0, a3, q2, q4, q5 ; computes q2 while loading q0 for next iter
KEY CONSTRAINTS & GOTCHAS
- SAR must be set before VMUL/VMULAS/CMUL — forgotten SAR causes wrong scaling.
- Only 8 QR registers (q0-q7) — register pressure is real. Plan allocation carefully.
- VLD/VST force address alignment — unaligned addresses silently read/write wrong data.
- No 32-bit multiply — only 8-bit and 16-bit vector multiply. Use multiple 16-bit ops for 32-bit.
- Zero-overhead loop limit — max ~56 instructions in loop body, no nested zero-overhead loops.
- ACCX is 40-bit — saturated to [-2^39, 2^39-1]. Read with RUR ACCX_0 + ACCX_1.
- QACC is per-lane — 16 lanes of 20-bit for S8/U8, 8 lanes of 40-bit for S16/U16.
- VADDS/VSUBS saturate — use when overflow is a concern; VMUL shifts and truncates (no sat).
- EE.VRELU modifies input register in-place — qs is both source and destination.
- Don't mix EE. and Xtensa native load/store on same address* without MEMW/DSYNC if caching matters.
- Assembly functions are declared with .balign 4 alignment.
QUICK DECISION TABLE: Which Instruction to Use
| C Operation | Data Type | Best PIE Instruction(s) |
|---|
c = a + b (element-wise) | int8/int16/int32 | EE.VADDS.S8/S16/S32 |
c = a - b (element-wise) | int8/int16/int32 | EE.VSUBS.S8/S16/S32 |
c = a * b >> shift | int8/int16 | EE.VMUL.S8/S16 (set SAR first) |
sum += a[i] * b[i] (scalar result) | int8/int16 | EE.VMULAS.S8/S16.ACCX |
accum[i] += a[i] * b[i] (per-lane) | int8/int16 | EE.VMULAS.S8/S16.QACC → EE.SRCMB |
c = max(a, b) | int8/int16/int32 | EE.VMAX.S8/S16/S32 |
c = min(a, b) | int8/int16/int32 | EE.VMIN.S8/S16/S32 |
c = a > 0 ? a : 0 (ReLU) | int16 | EE.VRELU.S16 qs, zero, zero |
c = a > 0 ? a : a*slope (PReLU) | int8/int16 | EE.VPRELU.S8/S16 |
c = a > b ? 0xFF : 0 (mask) | int8 | EE.VCMP.GT.S8 |
c = a & b | any | EE.ANDQ |
| `c = a | b` | any |
c = broadcast(scalar) | int8/int16/int32 | EE.VLDBC.8/16/32 |
| unaligned load | any | EE.LD.128.USAR.IP + EE.SRC.Q |
c = a << n (per 32-bit lane) | int32 | EE.VSL.32 (set SAR first) |
c = a >> n (per 32-bit lane) | int32 | EE.VSR.32 (set SAR first) |
| clear accumulator | - | EE.ZERO.ACCX / EE.ZERO.QACC |
| complex multiply | int16 | EE.CMUL.S16 |
| Radix-2 FFT butterfly | int16 | EE.FFT.R2BF.S16 |
FUNCTION TEMPLATE
.align 4
.text
.global my_kernel_name
.type my_kernel_name, @function
my_kernel_name:
# a2: output pointer (int16_t*, 16-byte aligned)
# a3: input0 pointer (int16_t*, 16-byte aligned)
# a4: input1 pointer (int16_t*, 16-byte aligned)
# a5: element count
entry sp, 64 # allocate stack frame
# Pre-loop setup
; set SAR if multiplying
; zero accumulators if accumulating
; broadcast scalars if needed
srai a5, a5, 3 # count → iterations (8 × int16 per 128-bit)
loopgtz a5, 0f
ee.vld.128.ip q0, a3, 16 # load input0
ee.vld.128.ip q1, a4, 16 # load input1
ee.vadds.s16 q2, q0, q1 # compute
ee.vst.128.ip q2, a2, 16 # store output
0:
retw
SUMMARY: Conversion Workflow
- Identify the C loop operation and data type (int8/int16/int32).
- Check alignment — ensure buffers are 16-byte aligned; use unaligned load pattern if not.
- Select the right PIE instruction from the decision table above.
- Set SAR if the instruction uses it (multiply, shift).
- Zero accumulators if using ACCX or QACC.
- Compute iteration count: N / (128/bits_per_element). E.g., int16 → N/8.
- Write the zero-overhead loop body using
loopgtz.
- Extract accumulator results (RUR.*) after the loop if needed.
- Watch register pressure — you only have q0-q7, plan which hold constants, which are temporaries.
REFERENCE DOCUMENTS
When you need to query complete instruction encodings, all instruction variants, detailed bit fields of special registers, exceptions/interrupts, or Xtensa native instructions, refer to the following reference files:
| Document | Path | Content |
|---|
| PIE Instruction Set Complete Reference | references/pie_instruction_set.md | All EE.* instructions with encoding, pseudocode, SAR/QACC/ACCX special register access, unaligned data handling, pipeline hazards |
| Xtensa ISA Reference | references/xtensa_isa.md | AR/FR/BR registers, all Xtensa native instructions (load/store/branch/call/loop/float/cache/TLB), exception vectors, special register map |
Reading Strategy: This skill file provides quick lookup tables and conversion templates. Please read the corresponding reference files when you need the following information:
- Exact bit encoding of instructions (instruction word encoding)
- Complete operation pseudocode (e.g., detailed formulas for all 16 lanes)
- Full segment access list for special registers (e.g., QACC_H_0
4, QACC_L_04)
- Xtensa native instructions (instructions without EE.* prefix)
- Exception handling, TLB, cache management
