tuyaopen-dev-loop

name	tuyaopen/dev-loop
description	Automated build-flash-monitor-analyze development loop for TuyaOpen devices. Covers log analysis, error patterns, CLI testing, and iterative debugging. Use when the user mentions dev loop, automated testing, log analysis, debug cycle, iterative development, or CI loop. 开发闭环、自动化测试、日志分析、调试循环、迭代开发。
license	Apache-2.0
compatibility	["TuyaOpen environment activated (export.sh / export.ps1 / export.bat)","Device connected via USB (MCU targets) or native Linux host"]

TuyaOpen Build-Deploy-Debug Loop

Loop Workflow

The standard development iteration cycle for TuyaOpen hardware:

┌─────────┐     ┌─────────┐     ┌─────────┐     ┌─────────┐     ┌─────────┐
│  Build  │────>│  Flash  │────>│ Monitor │────>│ Analyze │────>│ Decide  │
│         │     │         │     │  Logs   │     │ Results │     │         │
└─────────┘     └─────────┘     └─────────┘     └─────────┘     └────┬────┘
     ^                                                               │
     │                         ┌──────────┐                          │
     └─────────────────────────│ Fix Code │<─────── if error ────────┘
                               └──────────┘         if ok → done

Step-by-step

1. Build: tos.py build — compile firmware (see skill tuyaopen/build)

2. Flash: Flash firmware to the device from the project directory:

   tos.py flash -p <port>        # specify port (recommended)
   tos.py flash                   # auto-detect port
   tos.py flash -p <port> -d      # debug output
   

   T5 dual serial ports: T5/T5AI boards expose two serial ports. Typical mapping (not guaranteed):

   • Linux: flash = ttyACM0, monitor/log = ttyACM1
   • Windows: flash = lower COM number, monitor/log = higher COM number

   If flash fails on one port, swap to the other. Serial permission required on Linux (once): sudo usermod -aG dialout $USER then reboot.

3. Monitor / capture logs: tos.py monitor -p <port> for interactive sessions, or hands-off background logging via tuyaopen/debug-helper (monitor_helper.py start -p <port> → tail → stop).

4. Analyze: read the log file under <project_dir>/.target_logging/ for errors, warnings, crash indicators (patterns below)

5. Decide: pass (device healthy) or fail (fix code and restart loop)

LINUX shortcut

For LINUX platform targets, skip flash/monitor — use the bundled script:

$OPEN_SDK_PYTHON .agents/skills/tuyaopen/dev-loop/scripts/build_run.py          # build + run + auto-analyze (30s timeout)
$OPEN_SDK_PYTHON .agents/skills/tuyaopen/dev-loop/scripts/build_run.py 60       # custom timeout in seconds
$OPEN_SDK_PYTHON .agents/skills/tuyaopen/dev-loop/scripts/build_run.py 0        # no timeout

Or manually:

./dist/<project>_<version>/<project>_<version>.elf 2>&1 | tee device.log

Both dist/ (canonical output) and .build/bin/ (build intermediate) contain the ELF. Use dist/ for consistency.

Log Format & Patterns

TuyaOpen log format

[MM-DD HH:MM:SS ty X][source_file.c:line] message

Where X is the log level: E (error), W (warn), N (notice), I (info), D (debug), T (trace).

Key patterns to watch

Pattern	Meaning	Action
[... ty E]	Error-level log (PR_ERR)	Analyze the error message and source location
[... ty W]	Warning (PR_WARN)	Usually non-fatal but worth investigating
feed watchdog	Health monitor heartbeat (every ~10s)	Normal — device is alive
OPRT_ followed by negative number	SDK operation failed	Look up error code (see references/ERROR_CODES.md)
mqtt connected or MQTT_CONNECTED	Cloud connection established	Success — device is online
TUYA_EVENT_DIRECT_MQTT_CONNECTED	Direct MQTT event	Cloud connection confirmed
Replace the TUYA_OPENSDK_UUID	Placeholder credentials detected	User must configure real UUID/AuthKey
No output after flash	Device crashed or wrong serial port	Check baud rate and port; try reset
Repeated reset / boot loop	Crash during init or watchdog timeout	Check last error before reset
malloc failed or OPRT_MALLOC_FAILED	Out of memory	Reduce buffer sizes or optimize memory

Log level hierarchy

ERR > WARN > NOTICE > INFO > DEBUG > TRACE

Default log level: DEBUG. Set via tal_log_init(TAL_LOG_LEVEL_DEBUG, 1024, callback).

CLI Testing

Built-in CLI (tal_cli) via debug UART (prompt: tuya> ). Commands, registration, batch testing: references/ERROR_CODES.md.

Device State

State	Signal
Healthy	feed watchdog every ~10s; no PR_ERR after init; mqtt connected
No output	Wrong port, wrong baud, crash before log init
Boot loop	Crash in init — check last error before reset
Watchdog reset	Deadlock or infinite loop — check PR_ERR before reset
MQTT fail	Check network, credentials, PID mismatch
OPRT_MALLOC_FAILED	OOM — reduce buffer sizes

Agent Iteration Strategy

On build failure

1. Read the compiler error output carefully.
2. Identify the source file and line.
3. Fix the code.
4. tos.py build again. Repeat until build succeeds.

On flash failure

1. Check serial port (T5 dual-port: try the other port if flash fails — see the Flash step above).
2. Wait ~1 minute if port is busy.
3. Retry with the other port if available.
4. If still failing, ask the user to check hardware connection.

On runtime error (log analysis)

1. Capture log output after flash (monitor for 10-30 seconds).
2. Search for ty E (errors) and OPRT_ patterns.
3. Map error codes using references/ERROR_CODES.md.
4. Identify the source file and line from the log.
5. Fix the code based on the error context.
6. Restart the loop: build → flash → monitor.

On no output

1. Verify serial port and baud rate match the chip (check the baud rate table: T2=115200, T3/T5AI=460800, ESP32=115200, LN882H=921600).
2. Reset the device manually.
3. If still no output, the firmware may have crashed before log init — review recent code changes.

AI agent helper: tuyaopen/debug-helper (monitor_helper.py)

Full reference: skill tuyaopen/debug-helper. Script path (relative to SDK root):

.agents/skills/tuyaopen/debug-helper/scripts/monitor_helper.py

Logs are always written to <project_dir>/.target_logging/ (gitignored by the SDK).

Typical flow

# 1. Start background monitor (non-blocking)
$OPEN_SDK_PYTHON .agents/skills/tuyaopen/debug-helper/scripts/monitor_helper.py \
    --json start -p /dev/ttyACM1

# 2. Flash on the other port while monitor keeps logging
tos.py flash -p /dev/ttyACM0

# 3. Read log after boot
$OPEN_SDK_PYTHON .agents/skills/tuyaopen/debug-helper/scripts/monitor_helper.py \
    --json tail -n 200

# 4. Stop and release port
$OPEN_SDK_PYTHON .agents/skills/tuyaopen/debug-helper/scripts/monitor_helper.py stop

Iteration loop (analyze → fix → re-run)

Repeat until logs are clean:

1. Build → tos.py flash -p <port>
2. monitor_helper.py start -p <monitor-port> — capture boot + runtime trace
3. monitor_helper.py tail -n 200 → search ty E, OPRT_, watchdog, MQTT
4. Edit code → go to step 1
5. monitor_helper.py stop when done so the port is free for the next flash