| name | log-analyze |
| description | Analyze ArduPilot DataFlash .bin log files or MAVLink .tlog telemetry logs. Use when the user provides a .bin or .tlog log file path or asks to analyze flight log data. |
ArduPilot Log Analysis
You have a log extraction tool at .codex/skills/log-analyze/log_extract.py that handles common analysis tasks without writing one-off scripts. It supports both DataFlash .bin logs and MAVLink .tlog telemetry logs.
There is also a focused helper at .codex/skills/log-analyze/flow_cal_check.py for verifying optical-flow calibration against GPS truth (see "Optical-flow calibration check" below).
Prefer these tools over ad-hoc mavlogdump.py ... or python3 -c "..." one-liners. They wrap the common extraction, filtering, plotting, and summary paths in one reviewed command shape. When you genuinely need a custom extraction the tools can't do, write a small .py script and run it as python3 yourscript.py; don't hide it inside a one-liner.
Optical-flow calibration check
When verifying or setting FLOW_FXSCALER/FLOW_FYSCALER (or diagnosing optical-flow Loiter that drifts/leans), use the dedicated helper instead of hand-rolling the comparison - it encodes the lessons that a naive flow-vs-velocity check gets wrong.
python3 .codex/skills/log-analyze/flow_cal_check.py <log.bin> [--speed-min 1.0] [--qual-min 50] [--height auto|aglkf|rfnd]
Needs a flight with GPS (outdoors, as truth - flow may or may not be the nav source), flow logged (OF or ROFH), ATT, a height source (RFND or the AGL-KF XKF6), and IMU for the sensor-rate check. It compares the gyro-compensated flow rate to the flow rate implied by GPS velocity, per body axis, and reports:
- Sensor-rate check (run this conclusion first). It regresses the flow node's reported body rate against the flight-controller IMU gyro during rotation.
slope ~1.0 means the sensor clocks its output at the right rate. A slope far from 1 (e.g. ~0.5) means the whole sensor - flow AND its own gyro - is mis-rated, typically a DroneCAN flow node (ARK Flow/HereFlow) reporting integration_interval wrong or a bad IMU_INTEG_RATE/firmware. A FLOW_*SCALER cannot fix that (it scales flowRate, not bodyRate), so when the slope is off the helper suppresses the scaler suggestion. The fix for a HereFlow/DroneCAN node is FLOW_HF_RATEF = 1/slope (e.g. slope 0.52 -> FLOW_HF_RATEF=1.92): it scales flow and gyro together via integralToRate, so the EKF's gyro compensation stays valid - the thing the scaler can't do. The root cause is still sensor-side (the node's integration_interval / IMU_INTEG_RATE / firmware), so FLOW_HF_RATEF is a flight-controller-side correction, not a substitute for fixing the sensor. (FLOW_HF_RATEF is a SmallFastDrone-fork parameter; on stock ArduPilot the only fix is the sensor firmware.) Validated on an ARK Flow vehicle: slope 0.52 -> 1.00 and per-axis flow/ideal 0.50 -> 1.0 after setting it.
flow/ideal per axis - measured flow / GPS-implied flow = the scale error; prints the suggested FLOW_F*SCALER (forward motion -> FYSCALER, sideways -> FXSCALER), only when the sensor-rate check passed.corr and the motion split - each axis is fit only on samples where its own body-frame motion dominates, so a flight that does forward/back and strafe in separate segments calibrates both. An axis with too few samples is reported "not exercised" rather than given a garbage value.cross-axis per axis - flow that leaked onto the other axis during this motion. High (>15%) on a reliable axis means the flow frame is rotated or the compass/yaw is wrong - a per-axis scale cal cannot fix a rotation, so fix orientation/compass first.
--height picks the range source. aglkf (default when XKF6 is present, i.e. EK3_OPTIONS bit 4 set) uses the AGL-KF height the EKF actually feeds the flow fusion; calibrating against the same height the EKF uses makes the EKF velocity correct by construction. rfnd uses raw RFND.Dist.
Key interpretation rules (these are why the helper exists - each was a real misdiagnosis):
- The onboard
FlowCal is structurally blind to a whole-sensor rate error. It fits flow against the sensor's own gyro (bodyRate) and only samples during rotation; if both flow and gyro are scaled by the same factor it sees perfect consistency and reports no better scalar. flowX ~ bodyX "looking good" is the same trap - it's internal consistency, not absolute scale. Only an external reference (the FC IMU, or GPS over a known height) exposes it. This is exactly what the sensor-rate check is for.
- A
FlowCal no better scalar can ALSO mean the residual is not scale-shaped, i.e. a rotation/orientation error it cannot fit. Chase orientation, not the scaler, when cross-axis is high.
flow/ideal != 1 is ambiguous between flow scale and height. ratio ~= height_used / true_height when the flow is actually correct, so a half-reading rangefinder and a half-scale flow look identical. Validate the height independently: regress dRFND/dt against GPS-Doppler climb rate (-VZ) - terrain- and flow-independent; slope ~1 means RFND is right. Baro climb is often inflated near ground (prop wash), so do not trust baro/EKF altitude as the height reference.- A scale calibration that "keeps the same values" can mean the flight was one-directional in the body frame - yawing the nose to face the direction of travel puts ground left/right onto the forward axis. Strafe (hold heading, translate sideways at >1.5 m/s) to exercise the X axis.
- Comparing the EKF velocity (
XKF1.VN/VE) to GPS overstates the scale error vs the raw flow because of EKF filtering; this helper's body-axis flow/ideal is the honest number.
Standard Workflow
Step 1: Overview (ALWAYS do this first)
python3 .codex/skills/log-analyze/log_extract.py overview <logfile>
This gives you: message types with counts and fields, key parameters (including tuning PID gains, notch filter config, motor settings), flight modes, arm/disarm events, and errors. Read the output carefully before proceeding.
For .tlog files: The overview also shows source systems (vehicle, GCS, peripherals), status text messages, and suggests the vehicle system ID. Use --system <id> to filter by source system:
python3 .codex/skills/log-analyze/log_extract.py overview <logfile.tlog> --system 5
Step 2: Targeted Extraction
Based on what the overview reveals, extract specific data:
python3 .codex/skills/log-analyze/log_extract.py extract <logfile> \
--types XKF1 --condition "XKF1.C==0"
python3 .codex/skills/log-analyze/log_extract.py extract <logfile> \
--types BARO,RFND --fields Alt,Dist
python3 .codex/skills/log-analyze/log_extract.py extract <logfile> \
--types ATT --from-time 10.0 --to-time 30.0
python3 .codex/skills/log-analyze/log_extract.py extract <logfile> \
--types IMU --decimate 10 --limit 0
Step 3: Statistics
Compute min/max/mean/std/percentiles without custom scripts:
python3 .codex/skills/log-analyze/log_extract.py stats <logfile> \
--sources "RATE.YDes,RATE.Y,RATE.YOut,PIDY.P,PIDY.D"
python3 .codex/skills/log-analyze/log_extract.py stats <logfile> \
--types RATE --fields YDes,Y,YOut --from-time 10 --to-time 30
python3 .codex/skills/log-analyze/log_extract.py stats <logfile> \
--types XKF4 --fields SV,SP,SH --condition "XKF4.C==0"
Output includes: Count, Min, Max, Mean, Std, P5, P50, P95 for each field.
Step 4: Multi-Source Comparison
Compare data from multiple sensors aligned to a common time grid:
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe altitude
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe attitude
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe vibration
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe ekf_health
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe rc
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe pid_yaw
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe pid_roll
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe pid_pitch
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe rate_yaw
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe rate_roll
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe rate_pitch
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe rate_all
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe motor_output
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> --recipe ctrl_rms
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> \
--sources "BARO.Alt,RFND.Dist,-XKF1.PD"
Step 5: Plot (when visual analysis helps)
python3 .codex/skills/log-analyze/log_extract.py plot <logfile> \
--recipe altitude --output /tmp/altitude.png
python3 .codex/skills/log-analyze/log_extract.py plot <logfile> \
--recipe pid_yaw --from-time 30 --to-time 35 --output /tmp/pid_yaw.png
python3 .codex/skills/log-analyze/log_extract.py plot <logfile> \
--recipe rate_yaw --output /tmp/rate_yaw.png
python3 .codex/skills/log-analyze/log_extract.py plot <logfile> \
--recipe ctrl_rms --output /tmp/ctrl_rms.png
python3 .codex/skills/log-analyze/log_extract.py plot <logfile> \
--sources "RATE.YDes,RATE.Y" --output /tmp/yaw_tracking.png
python3 .codex/skills/log-analyze/log_extract.py plot <logfile> \
--types XKF4 --fields SV,SP,SH --output /tmp/ekf_var.png
python3 .codex/skills/log-analyze/log_extract.py plot <logfile> \
--recipe altitude --from-time 10 --to-time 60 --output /tmp/takeoff.png
After generating a plot, read the image file to view it.
Available Recipes
| Recipe | Description | Sources |
|---|
altitude | Altitude comparison | BARO, RFND, EKF, CTUN/QTUN |
attitude | Attitude actual vs desired | ATT Roll/Pitch/Yaw + Des |
vibration | Vibration analysis | IMU AccXYZ, VIBE XYZ |
ekf_health | EKF variances | XKF4 SV/SP/SH/SM/SVT |
rc | RC input vs output | RCIN/RCOU C1-C4 |
pid_roll | Roll PID components | PIDR P/I/D/FF |
pid_pitch | Pitch PID components | PIDP P/I/D/FF |
pid_yaw | Yaw PID components | PIDY P/I/D/FF |
rate_roll | Roll rate tracking | RATE RDes/R/ROut |
rate_pitch | Pitch rate tracking | RATE PDes/P/POut |
rate_yaw | Yaw rate tracking | RATE YDes/Y/YOut |
rate_all | All axes rate tracking | RATE Des/Act all axes |
motor_output | Motor outputs | RCOU C1-C4 |
ctrl_rms | Controller RMS values | CTRL RMSRollP/D, PitchP/D, Yaw |
Analysis Methodology
- Extract data first, theorize second. Always run
overview then targeted extractions before forming hypotheses.
- Cross-check multiple sensors. Never trust a single source. Compare EKF estimate against raw sensors (baro, rangefinder, GPS).
- Check the events timeline. ARM/DISARM, mode changes, and errors give crucial context.
- Filter EKF by core. XKF* messages have a
C field for core index. Use --condition "XKF1.C==0" to isolate one core.
- Mind the units. XKF1 angles are in centidegrees. PD is positive-down (NED). BARO.Alt is meters above origin. RFND.Dist is meters.
- Use stats for quantitative comparison. When comparing axes or checking for oscillation,
stats gives instant min/max/mean/std without custom scripts.
- Verify servo/motor mapping before naming motors. See "Vehicle Identification Reconnaissance" below. Do not assume
ESC.Instance==N is "Motor N" — check SERVO*_FUNCTION values in the log and translate.
- Separate physical vehicles even when the build spec is identical. Logs from before and after a crash/rebuild are from different hardware. See "Multi-Log and Cross-Flight Analysis" below.
BAT.Curr is pack-level, not per-motor. ESC.Curr is often zero on DShot bidir — verify before relying on it.- Aerodynamic body effects pollute in-flight calibration measurements. On airframes with meaningful body lift, control fins, or significant drag, any in-flight attempt to characterise the thrust curve, hover throttle, or PID plant above low airspeed (~5–10 m/s) is contaminated by speed-dependent non-rotor contributions. Clean measurements for these quantities need static/bench conditions or stable-hover segments at minimal forward speed.
- Two-instance sensor analysis: focus on what was the same on both instances, not what differed. When a sensor has two instances (compass, GPS, IMU, baro), the failing instance is rarely the diagnostic target — both instances usually see the same external event with different sensitivity, and the one that drops is just the one with less margin. Pull both, then ask "what was the same on both around the event?" That answer is the root cause; the asymmetric response is downstream of it. Ignoring this leads to "GPS2 is broken, replace it" recommendations when GPS2 is fine and a passing jammer was the cause.
- Verify the user's theory rather than inheriting it. Customer reports often correctly identify the time and direction of a failure but mis-name the cause. Common substitutions: "GPS glitch" when actually compass; "multipath" when actually interference; "motor failure" when actually mixer saturation. Restate the user's theory as your first step, then build the diagnosis to confirm or disconfirm it explicitly. Do not assume the theory is right and look for confirming evidence — that is the standard route to a wrong fix.
Vehicle Identification Reconnaissance
Before analysing per-motor data, always verify the servo-to-motor mapping from the log itself:
python3 .codex/skills/log-analyze/log_extract.py extract <logfile> \
--types PARM --condition "PARM.Name=='SERVO1_FUNCTION' or PARM.Name=='SERVO2_FUNCTION' or PARM.Name=='SERVO3_FUNCTION' or PARM.Name=='SERVO4_FUNCTION'"
The trap: ESC.Instance==N corresponds to the SERVO(N+1) output channel, not to ArduPilot's motor number. On a vehicle with non-standard SERVO*_FUNCTION assignments, ESC.Instance==3 can be Motor 2 rather than Motor 4 — or any other mapping. The motor roles are the SERVO_*_FUNCTION values (33-36 for quad motors 1-4, with higher values for hexa/octa), not the channel index or the ESC instance.
| Log field | What it identifies |
|---|
ESC.Instance | Zero-indexed ESC order (0-3 for a quad) |
RCOU.CN | PWM output channel N (1-indexed) — same as SERVON |
SERVO_N_FUNCTION | The motor role assigned to that output channel |
Consequence of getting it wrong: you blame a motor that's actually the healthiest while the actual weak channel goes uninvestigated. The symptom is often "the motor I flagged doesn't match what the pilot reports as having felt off."
Hexa, octa, and coax mappings are even easier to misread. On any non-standard build or any diagnosis that names a specific physical motor, make the mapping table explicit in your analysis output.
Pack Current vs Per-Motor Current
BAT.Curr is total pack current. It is not per-motor current. Three common errors from conflating them:
- Estimating per-motor thermal load during aggressive manoeuvres. The mixer creates asymmetry under roll/pitch correction — one motor can be at 90% throttle while another is at minimum spin. During such events a single motor may be drawing 35-40% of pack current, not 25%. Worst-case per-motor share is roughly
pack / 3, not pack / 4.
- Reasoning about
MOT_BAT_CURR_MAX as a per-motor limit. It is a pack-level limit. The mixer cannot enforce per-motor current caps.
- Assuming
ESC.Curr is populated. On many DShot300/600 bidir setups ESC.Curr is zero — the telemetry frame does not include current, only RPM (and sometimes temperature). Verify the stats are non-zero before relying on it; if zero, you only have pack-level current.
Multi-Log and Cross-Flight Analysis
Vehicle Identity
Before correlating observations across multiple logs, establish that the logs are from the same physical vehicle. Same firmware, same FRAME_CLASS, same param file, and even same pilot does not guarantee same hardware. A rebuilt airframe after a crash is a different vehicle regardless of how much of the spec is preserved. Motor/ESC/prop health observations do not transfer across a rebuild.
Heuristics for establishing continuity:
STAT_BOOTCNT and STAT_FLTTIME should monotonically increase across logs from the same airframe- Large gaps in time with
STAT_FLTTIME reset or dropping indicate a new vehicle (or a flight-time reset, which is itself a reason to double-check)
- A crash event in one log followed by subsequent logs should be treated as a different vehicle until explicitly confirmed otherwise
Do not carry forward "Motor X is weak" findings across a rebuild. The failure mode may recur (same airframe type under similar maneuvres will have similar failure modes) but the specific weak channel is a property of the current physical hardware.
Chronological Per-Motor Diagnostics
When you have multiple logs from a single confirmed-same vehicle spanning hours or days, per-motor patterns become visible that don't show up in any individual log:
Per-ESC error-rate sweep. ESC.Err (DShot bidir error rate %) per ESC.Instance across a day of flights reveals motor-channel degradation:
for log in log1.bin log2.bin ... ; do
for inst in 0 1 2 3; do
python3 .codex/skills/log-analyze/log_extract.py stats "$log" \
--sources "ESC.Err" --condition "ESC.Instance==$inst and ESC.RPM>1000"
done
done
Patterns to look for:
- Baseline outlier: one instance with
max error rate 10-100× its peers during a flight where everything else is clean. This is the earliest fingerprint of a weakening channel and often appears in flights the pilot reports as "fine."
- Single-flight transient > 30%: a "ground the vehicle" event. Even if nothing catastrophic happened in that flight, a DShot error rate spike that high indicates the ESC-motor link is intermittently losing frames; the next aggressive flight is where it fails. Treat log37-class events (one big spike before a crash) as preventable warnings.
- Across-flight climb: per-motor error rate climbing steadily across a day is predictive of imminent desync/burnout.
These patterns require same-vehicle continuity to read correctly — see "Vehicle Identity" above.
Operating-envelope thresholds. On a specific vehicle, the pack-current level at which DShot errors begin to cross 1% is an empirical electrical-stress threshold for that combination of motor + ESC + pack + cooling. Cross-reference BAT.Curr with ESC.Err in the same time window to find it:
python3 .codex/skills/log-analyze/log_extract.py compare <logfile> \
--sources "BAT.Curr,ESC.Err" --interval 0.25 --from-time <peak_start> --to-time <peak_end>
This threshold is a hardware-specific measurement that drifts down as batteries age and motor runtime accumulates. It is a useful per-vehicle health signal but does not transfer across vehicles even of the same build.
Parameter-Change Safety Rules
These are general rules for when recommending parameter changes from log evidence is or is not appropriate. The underlying principle: a PID or filter value that came out of autotune, a calibration run, or bench measurement represents actual airframe dynamics; overriding it without new measurement evidence replaces data with opinion.
Before recommending any tuning change, ask: what would I measure in the log to show this specific parameter is the problem, and have I actually measured that? If the answer is "I'm interpolating from general rules," do not recommend it.
Rate-Loop Gains Post-Autotune
Recommend a change when:
- Rate-tracking data shows sustained error with large I-term accumulation that doesn't decay during the manoeuvre
CTRL.RMS values show sustained oscillation on a specific axis in normal flight- PID component stats show a specific term saturating at its IMAX/PDMX limit
Do not recommend a change when:
- The apparent tracking error is at a flight condition autotune never tested (forward speed, attitude extremes, near-vertical attitude where body-frame rate axes are kinematically coupled). These are often physics, not gain.
- The mean error is small and only the peaks are large — autotune's output already handles the mean correctly, and peaks come from transient disturbances the PID loop is actually doing the right thing about.
- The "error" at peak speed is really the rate loop delivering less output than demanded because motor authority is saturated. Raising P does not create thrust headroom.
ATC_RAT_*_SMAX
Never recommend setting this on a copter rate PID. The slew-rate modifier (Dmod in libraries/AC_PID/AC_PID.cpp:263-267) scales only the rate-loop P and D outputs:
_pid_info.Dmod = _slew_limiter.modifier((_pid_info.P + _pid_info.D) * _slew_limit_scale, dt);
P_out *= _pid_info.Dmod;
D_out *= _pid_info.Dmod;
The upstream angle P gain (ATC_ANG_*_P) is not scaled. When SMAX engages, the angle loop continues commanding full-authority rate demands while the rate loop's ability to follow them has been cut. The loop mismatch can drive oscillation and outright instability, especially on airframes with above-default angle P gains.
Use IMAX for integrator runaway protection and PDMX for P-output capping. Both act honestly in the rate loop without hiding their effect from the angle loop.
ATC_RAT_YAW_D
Yaw D is a narrow parameter in ArduCopter — typical values are 0.000–0.005. Many airframes converge at AUTOTUNE_MIN_D (default 0.0003) during yaw tuning.
Autotune converging at MIN_D is a signal, not an artefact. Autotune scans D upward looking for damping improvement and stops at the lowest value where the test metric either stops improving or starts oscillating. Landing at the floor means the airframe does not tolerate more yaw D.
Raising yaw D above autotune's output puts D-term output into the same order of magnitude as P-term output under buffet or noise. On a quad, yaw torque comes from differential thrust — every unit of yaw D output drives repeated asymmetric motor loading. This is a documented cause of motor/ESC thermal failure on high-TWR quads.
Recommend raising yaw D only with specific evidence:
PIDY.Dmod-limited events in hover (indicates the rate loop is actively damping something)- Sustained yaw-rate oscillation that P-gain changes alone can't explain
- Bench or flight data showing a specific damping deficit
Do not recommend raising it on "it's at the minimum, we have room" reasoning.
ATC_INPUT_TC
This is a pilot-feel parameter, not a log-derivable parameter. ATC_INPUT_TC controls the time constant of the angle target's response to stick input in angle modes (STABILIZE, ALT_HOLD, LOITER). Its "right" value is subjective.
Recommend a change only on pilot report:
- Pilot reports perceived lag or sluggishness → consider lowering
- Pilot reports overshoot or twitchy feel → consider raising
- If the pilot hasn't complained, don't touch it.
Do not recommend a change based on:
- Rate-demand peak data alone (the peaks scale with any TC change, so there's no baseline to compare against)
- Cross-vehicle comparison or "typical for this airframe class"
Cost of lowering: halving TC roughly doubles the peak rate demand for the same stick input. On a vehicle already saturating the rate loop or motor output at peak throttle, lowering TC moves more load into the saturation regime. Verify headroom before recommending a decrease.
MOT_SPIN_MAX vs MOT_BAT_CURR_MAX (Motor Thermal Protection)
When the goal is to protect motors or ESCs from thermal burnout (over-volted motors, marginal continuous current rating, cooling problems), use MOT_BAT_CURR_MAX with a value from component specifications, not MOT_SPIN_MAX.
Why MOT_SPIN_MAX is the wrong tool for thermal protection:
MOT_SPIN_MAX clips at the actuator stage (libraries/AP_Motors/AP_MotorsMulticopter.cpp:468) after the mixer has computed per-motor thrust contributions assuming the full [0, 1] range was available. When spin_max < 1.0, the mixer silently commands more than it gets. The rate loop absorbs the mismatch via attitude error. Invisible on benign flights; growing under saturation.
Why MOT_BAT_CURR_MAX is the right tool:
MOT_BAT_CURR_MAX modulates _throttle_thrust_max (libraries/AP_Motors/AP_MotorsMulticopter.cpp:348-385), which the mixer uses as its input ceiling at libraries/AP_Motors/AP_MotorsMatrix.cpp:234-244. The mixer sees the reduced ceiling and plans around it. No loop mismatch. ATC_THR_MIX_MAN/MAX still applies — when the mixer saturates against the reduced ceiling, attitude is still prioritised over throttle.
The mechanism: when measured current exceeds the limit, _throttle_limit decreases (smoothed by MOT_BAT_CURR_TC, default 5 s), and max throttle is pulled down to throttle_hover + (1 − throttle_hover) * _throttle_limit. The floor is throttle_hover, so the vehicle can always hover.
Time-scale caveat: MOT_BAT_CURR_MAX protects against sustained over-current (seconds-scale, matching motor thermal failure modes). It does not protect against millisecond-scale ESC desync under abrupt PWM step commands — that's ESC firmware territory, not tuning.
Picking a value: should come from the lower of:
- Battery continuous C-rating × capacity
- ESC continuous current rating × motor count (with margin for mixer asymmetry — worst case is pack/3 on one motor, not pack/4)
- Motor continuous current rating (thermally derated for the actual operating voltage)
- Empirical operating-envelope threshold from logs, if available
If component specs are unknown, the operating envelope (where DShot errors begin to cross 1% in existing logs) is a data-driven starting point. Always pick the lower of the envelope and the spec.
MOT_THST_EXPO
MOT_THST_EXPO should be measured on a thrust stand, not derived from flight logs. It is ArduCopter's inverse of the empirical thrust curve thrust = (1 − expo) * actuator + expo * actuator². A wrong value means every commanded thrust becomes a wrong actuator command, and the PID loop fit depends on the assumed curve being close to the real one.
Recommend a change in direction when:
- Physics of the prop suggests default doesn't apply. High-pitch props, large-diameter props, or props with notably high static torque draw (heavy drag at low RPM) typically need higher expo than default (0.65). Low-pitch racer props typically match default.
ESC.RPM vs commanded actuator in log data is notably shallower than RPM ∝ √throttle would predict — the signature of a drag-loaded prop-motor system where the default curve doesn't fit.
Do not recommend a specific numerical value from log data alone:
- In-flight thrust measurements are corrupted by aerodynamic body lift above low airspeeds (~5–10 m/s)
- Vehicles rarely sit in clean stable hover long enough for accurate curve fitting
- Without known mass or a direct thrust measurement, accel integration can't be converted to thrust
MOT_THST_HOVER may be frozen (MOT_HOVER_LEARN=0) and unreliable as a cross-check if the curve is wrong
Required follow-up after any MOT_THST_EXPO change: re-run AUTOTUNE. The existing tune was measured against the old thrust model. Changing the model shifts the plant the PID loops see, invalidating the fit. Do not fly aggressive envelopes on pre-change gains.
Bench procedure (canonical):
- Mount one motor+prop+ESC on a thrust stand at the actual operating voltage
- Sweep actuator from
MOT_SPIN_MIN to MOT_SPIN_MAX in ~20 steps, holding each 2-3 s
- Record actuator, thrust, RPM, current, voltage
- Fit to
thrust = (1 − expo) * a + expo * a² and read off expo
- Apply, re-run
AUTOTUNE, validate with stable hover across three battery-voltage states before aggressive flight
EK3_GLITCH_RAD — Two Modes
EK3_GLITCH_RAD is not a simple "how aggressive is GPS glitch rejection" knob — it selects between two different code paths in libraries/AP_NavEKF3/AP_NavEKF3_PosVelFusion.cpp (branches at lines 819-829, 894-905, 942-951).
EK3_GLITCH_RAD > 0 (default 25): innovation tests that fail trigger ResetPosition() to the GPS fix when position variance grows beyond GLITCH_RAD². Appropriate for hover-class copters where a 25 m innovation is almost certainly a bad GPS fix.EK3_GLITCH_RAD <= 0 (special case): innovation variance is scaled by the failed test ratio, bounding the state update without triggering a reset. The EKF stays on its IMU prediction and corrects toward GPS gradually.
Which to use depends on the vehicle's operational envelope:
- Hover-class / slow cruise copters (typical multirotors): default 25 is correct. Glitch rejection protects against real bad fixes.
- High-speed vehicles (sustained >30-50 m/s cruise or aggressive acro): set to 0. GPS processing latency of ~100 ms is already 5 m of apparent position error at 50 m/s and 10 m at 100 m/s. Combined with covariance growth from high dynamics, the
> 0 path triggers ResetPosition() to the lagged GPS fix, snapping the state to where the GPS thinks the vehicle is. This is a flyaway mechanism at high speed. The <= 0 path handles the same large innovations bounded-variance style.
Log diagnostic: "GPS Glitch or Compass error" in MSG/STATUSTEXT during aggressive flight is the innovation test firing. With GLITCH_RAD <= 0 the special path handles the update safely and no reset occurs. With GLITCH_RAD > 0 the same message is followed by position snaps and often EKF lane switch events that may look like EKF health failures but are actually the reset mechanism misfiring.
Do not recommend "set GLITCH_RAD back to 25" on a high-speed platform as a fix for EKF messages during peak-speed flight. On those vehicles, the default value is the wrong one, and the messages are a normal consequence of the innovation test at high dynamics — they are not evidence of a bad GPS fix.
Compass Yaw Sanity Check (180° / 90° Heading Errors)
A compass that reports yaw 90° or 180° wrong is one of the most dangerous and most-missed pre-flight failure modes — pre-arm cannot catch it because the vehicle is stationary and GPS course is undefined. The vehicle arms cleanly, then flies sideways or backwards into the ground at the first commanded position move.
In-flight signature (in this order):
- Position controller commands sustained forward pitch/roll for a position move; vehicle accelerates in the wrong direction.
- EKF GPS innovations (
XKF3.IVN, IVE, IPN, IPE) ramp continuously and pin at the gate value as the position controller pushes harder.
EKF3 lane switch events as cores disagree about the right answer.- Status text:
"GPS Glitch or Compass error" — this message is generic and can mean either; the log tells you which.
EKF3 IMU0 emergency yaw reset (and IMU1) — yaw snaps by ~90° or 180° in one sample as the EKF gives up and aligns to GPS.- After disarm:
"PreArm: AHRS: EKF3 Yaw inconsistent N deg. Wait" where N is close to 90 or 180 — direct numerical confirmation of the heading error.
Diagnostic — compare EKF yaw to GPS ground course during forward flight:
python3 .codex/skills/log-analyze/log_extract.py plot <log> \
--sources "ATT.Yaw,GPS.GCrs" --from-time <move_start> --to-time <move_end>
During steady forward flight at >2 m/s, ATT.Yaw and GPS.GCrs should agree to within ~10° (the residual is wind drift). A flat persistent offset of ~90°, ~180°, or ~270° across the entire moving segment is a compass orientation/calibration error. Stationary segments are not informative — GCrs is undefined at zero speed.
Disambiguating "GPS Glitch or Compass error":
The EKF cannot distinguish a wrong heading from a wrong GPS fix from inside the filter — both produce GPS innovations the same way. The message names both because either could be the cause; the log tells you which:
| Evidence | Cause |
|---|
GPS.NSats stable, GPS.HDop stable, both GPS instances agree on position | Compass |
GPS.NSats drops, GPS.HDop spikes, or two GPS instances disagree on position | GPS |
ATT.Yaw differs from GPS.GCrs by ~90°/180°/270° during forward flight | Compass |
Post-event "EKF Yaw inconsistent N deg" with N near 90 or 180 | Compass (N is the actual error) |
uBlox MON-HW agcCnt drops at the same instant | GPS (interference — see uBlox section below) |
Pre-arm limitation: the GPS-course/compass consistency check requires forward motion. A stationary vehicle cannot trigger it. Catching this on the ground requires either an external reference (sun compass, known landmark bearing) or a brief taxi/walk-forward step before takeoff to confirm XKF1.Yaw matches GPS.GCrs.
Reversed Yaw / Wrong FRAME_TYPE (Props-In vs Props-Out)
A multirotor whose configured FRAME_TYPE has the wrong motor rotation directions for the physical build — most commonly BetaFlightX (FRAME_TYPE=12, props-in) flashed onto a props-out airframe that needs BetaFlightXReversed (FRAME_TYPE=15), or the reverse — has its yaw torque sign inverted while roll and pitch are unaffected. The vehicle then yaws away from any disturbance under positive feedback: the harder the controller corrects, the faster it spins. On a throw, hand-launch, or first takeoff this presents as an uncontrollable yaw spin that "spins itself into the ground" with roll/pitch looking fine the whole way down.
Why roll/pitch survive but yaw inverts. Roll and pitch torque come from which motors thrust harder — a function of motor position, unchanged by reversing spin direction. Yaw torque comes from the net rotor reaction torque — a function of motor rotation direction, which flips sign when props/rotation are reversed. So a reversed build flies roll/pitch normally and is divergent in yaw only. "Roll/pitch controlled, yaw runs away" is the fingerprint; do not mistake it for weak yaw authority or an aggressive throw spin.
The decisive test — command sign vs response sign. Insufficient yaw authority lets the spin coast at a roughly constant rate; inverted yaw makes it accelerate in the commanded-against direction. Pick a window where the controller is steadily fighting the spin (yaw demand one sign, not wrapping) and compare the rate-loop output to the actual yaw acceleration:
python3 .../log_extract.py extract <log> --types RATE --fields YDes,Y,YOut \
--from-time <t0> --to-time <t1> --limit 0
- Correct frame: sustained positive
YOut drives RATE.Y more positive (toward zero if braking a negative spin). Command and response share sign.
- Reversed frame: sustained positive
YOut drives RATE.Y more negative — command and response have opposite signs, and |RATE.Y| grows while the controller commands maximum opposing torque. That is proof, not inference.
Cross-check the rate-loop output against raw IMU.GyrZ (rad/s) so the conclusion does not rest on a single logged field, and confirm RATE.R/RATE.P track their demands normally (roll/pitch healthy) to complete the asymmetry.
Heading-wrap red herring. At multi-rev/s spin the angle loop's wrapped heading error makes RATE.YDes periodically dive to match the spin (and YOut collapse to ~0) once per revolution — see the runaway sweep through the target. That is the angle controller momentarily pointing the same way as the runaway, a symptom of the spin, not its cause. Diagnose on the steady-demand segment, not the wrap.
Confirm and fix. FRAME_CLASS + FRAME_TYPE from PARM, then make the configured rotation match the hardware: either switch FRAME_TYPE between 12 (BetaFlightX) and 15 (BetaFlightXReversed), or reverse all four motor directions (DShot reverse, or swap two phase wires per motor) to match the configured frame. Bench-verify before flight: command yaw in one direction in a motor test and confirm the airframe wants to rotate that way. A reversed frame diverges in yaw on any takeoff, not only on a spin-throw — so this is a ground-checkable, deterministic fault, not a flight-condition edge case.
GPS Receiver Health Diagnostics (uBlox MON-HW / MON-HW2)
uBlox-based GPS units (GPS_TYPE=2) emit per-instance hardware-monitor messages that distinguish interference from multipath from antenna fault from constellation outage. The fields are routinely under-used because the field interpretations are non-obvious — and several of them are counter-intuitive.
Message names (logged once every ~5 s per instance):
| Message | Source | Content |
|---|
UBX1 | GPS instance 0 | MON-HW: noisePerMS, jamInd, aPower, agcCnt |
UBX2 | GPS instance 0 | MON-HW2: ofsI, magI, ofsQ, magQ |
UBY1 | GPS instance 1 | MON-HW (same fields as UBX1) |
UBY2 | GPS instance 1 | MON-HW2 (same fields as UBX2) |
Field interpretations — the intuitive readings are wrong; read carefully:
| Field | Healthy | Meaning |
|---|
agcCnt | 4000–5000 | AGC count. Lower = strong incoming RF forcing AGC to back off. The receiver is reducing front-end gain because something is too loud. The most reliable interference indicator. |
noisePerMS | 65–95 | Receiver-measured noise. Counter-intuitively drops during strong narrowband interference — AGC clamp suppresses everything, including the noise-floor measurement. Do not interpret a drop as "improvement". |
jamInd | 0–30 | Jamming indicator. Unreliable on its own. It is calibrated against initial conditions and tends to under-report sustained narrowband interference. Don't trust jamInd to decide whether interference is happening — use agcCnt. |
aPower | 1 | Antenna power state. 0 = open or short feedline. Decisive when present — points at hardware fault, not interference. |
magI, magQ | 100–170 | I/Q channel signal magnitudes. Drop below ~50 = front-end saturated/compressed. Second most reliable interference indicator after agcCnt. |
ofsI, ofsQ | -10 to 25 | I/Q DC offsets. Persistent large values point to receiver hardware issues, not interference. |
Interference vs multipath signature comparison:
| Multipath | Interference | Antenna fault |
|---|
agcCnt | unchanged | drops sharply | rises (toward max) |
magI / magQ | unchanged | drop sharply (often <50) | drop |
noisePerMS | unchanged or slight rise | drops with AGC clamp | rises |
aPower | 1 | 1 | 0 |
NSats | gradual decrease | full loss possible | progressive loss |
HAcc while fix held | inflated to several metres | stays at cm-level on unaffected receiver | N/A (loss of fix) |
| Affected sky region | low-elevation satellites | whole sky | whole sky |
| Both instances affected? | typically yes, similar magnitude | yes, often asymmetric (whichever antenna sees the source more) | typically only the one with the broken cable |
| Recurrence | site-specific | source-of-RF-specific | deterministic, every flight |
Workflow when a GPS dropout is suspected:
- Confirm dropout: extract
GPS.Status, GPS.NSats, GPS.HDop (and GPS2.* if present). A dropout shows Status=1, NSats=0, HDop=99.99.
- Plot the hardware monitor data on both receivers across the dropout window:
python3 .codex/skills/log-analyze/log_extract.py plot <log> \
--sources "UBX1.agcCnt,UBY1.agcCnt,UBX1.noisePerMS,UBY1.noisePerMS"
python3 .codex/skills/log-analyze/log_extract.py plot <log> \
--sources "UBX2.magI,UBX2.magQ,UBY2.magI,UBY2.magQ"
- Match the pattern: AGC drop + magI/magQ collapse → interference. Sat count drift but stable AGC → multipath/sky obstruction.
aPower=0 → hardware fault.
- Check EKF response:
NKF4.GPS (or XKF4.GPS) shows which instance the EKF is using. If the working instance was already primary, the vehicle should be unaffected.
- Asymmetry between instances (one drops, the other holds) usually means antenna/feedline placement difference, not module difference — the two receivers are configured the same and saw the same external event with different physical coupling.
Before Recommending a Fix — Verification Checklist
Do NOT send a diagnosis or recommendation to the user until you have independently verified it against every corroborating data stream in the log. A plausible-sounding theory is not evidence.
For every hypothesis, walk through this list before reporting:
| Claim type | Data you MUST also pull before concluding |
|---|
| "Sensor X is wrong" | The other instance of the same sensor (IMU 0 vs 1, BARO 0 vs 1, GPS 1 vs 2) and the EKF innovation for that sensor. If both instances agree, it is not a sensor fault. |
| "Motor / frame asymmetry" | RCOU.C1…Cn at stable hover AND during the event; ESC[i].RPM if available. Quantify the diagonal-pair imbalance. |
| "Motor saturation limits authority" | RCOU values vs MOT_SPIN_MIN / MOT_SPIN_MAX / MOT_PWM_MIN / MOT_PWM_MAX. A motor pegged at the floor during a climb overshoot is proof, not speculation. |
| "EKF is falsely reporting climb/descent" | XKF3 innovations (IVD, IPD), both IMUs' raw AccZ, and BARO.Alt. All three should disagree with the EKF before you blame the filter. |
| "GPS glitch caused failsafe" | GPS.Spd and GPS.Alt at the instant of the ERR, plus GPS.NSats and HDop to show it wasn't a coverage issue. Show the innovation spike (XKF3.IVE/IVN/IPE/IPN), not just the ERR message. |
| "GPS receiver dropped fix / RTK lost" | uBlox MON-HW agcCnt and MON-HW2 magI/magQ on both receivers during the dropout window; the other GPS instance's status; the EKF's NKF4.GPS (or XKF4.GPS) source field; and aPower. Distinguish interference (AGC drops) from multipath (no AGC drop) from antenna fault (aPower=0) before recommending action. See "GPS Receiver Health Diagnostics" above. |
| "Compass / heading is wrong" | ATT.Yaw vs GPS.GCrs during steady forward flight at >2 m/s — must agree to ~10°. A flat persistent ~90°/180°/270° offset is direct evidence; "EKF Yaw inconsistent N deg" post-event is the numerical confirmation. Innovation spikes alone are not enough — they only show that something disagrees with GPS, not that compass is the wrong something. See "Compass Yaw Sanity Check" above. |
| "Uncontrolled yaw spin / reversed FRAME_TYPE" | A steady-demand window of RATE.YDes/YOut vs RATE.Y (and raw IMU.GyrZ): sustained one-sign YOut driving yaw acceleration the same sign is inverted yaw, not weak authority (which coasts). Confirm RATE.R/RATE.P track normally (roll/pitch healthy) and read FRAME_TYPE. See "Reversed Yaw / Wrong FRAME_TYPE" above. |
| "Source-set / failover recommendation" | See EKF source-set playbook note in libraries/AP_NavEKF3/AGENTS.override.md — source sets are manually switched, not automatic failover. Do not recommend EK3_SRC2_* as a "fallback" for glitch response. |
| "Fence action caused the crash" | MODE changes AND fence ERR codes AND aircraft state (alt/speed) at fence breach time. |
Rule of thumb: If a reviewer asked "how do you know?", you should be able to cite a specific row from the log. If the answer is "it's consistent with the symptom", you have not finished verifying.
Worked example — "climbs when moving left" misdiagnosis
Initial plausible-but-unverified theory: "accelerometer misalignment during hard left roll creates a false climb signal in the EKF". Evidence that seemed to support it: XKF3.IVD positive (GPS disagrees with EKF), both baro and EKF show climb.
What actually showed up on full verification:
- IMU 0 and IMU 1 AccZ traces were within 0.1 m/s² through the whole event → not an IMU fault.
RCOU.C1..C4 at hover: 1455, 1475, 1186, 1277 — a ~250 PWM diagonal asymmetry. Motor 3 sat near MOT_SPIN_MIN before anything went wrong.- During left-roll events, the roll mixer drives M3 below its floor;
CTUN.ThO hits 0.00 but M3 stays pinned at 1150 → the vehicle physically cannot descend.
- On right-roll events M1/M4 are decreased instead, both have headroom, no symptom.
The root cause was a frame/yaw build asymmetry leaving M3 at saturation. Recommending EKF parameter changes would have been a dead end. The verification table above is exactly what flushed this out.
Oscillation Diagnosis Workflow
When investigating oscillation or tuning issues:
- Overview — check ATC_RAT_* gains, SMAX, filter cutoffs, notch config
- Stats —
--sources "CTRL.RMSRollD,CTRL.RMSPitchD,CTRL.RMSYaw" to identify which axis
- PID plot —
--recipe pid_yaw (or roll/pitch) to see P/I/D/FF components
- Rate tracking —
--recipe rate_yaw to check desired vs actual tracking quality
- Zoom in — use
--from-time/--to-time on plots to examine specific maneuvers
Vibration and Harmonic-Notch Analysis (FFT from a log)
When VIBE.VibeX/Y/Z is high (over ~15 m/s² sustained / ~30 peak) or you suspect the notch is mistuned, you can FFT the batch-sampled IMU and read the spectrum directly. VIBE gives you the magnitude; the FFT gives you the frequency.
Source data: ISBH/ISBD batch samples. When INS_LOG_BAT_MASK is set, the IMU logs raw blocks of 2048 samples at the sensor rate (often ~4 kHz) — far above the 400 Hz IMU message and the only data fast enough to FFT the motor fundamental. log_extract.py has no FFT subcommand, so write a one-off script using pymavlink to read ISBH (header) + ISBD (data arrays), assemble each 2048-sample window, and average per-window PSDs (Welch-style). Pitfalls that will bite you:
- Time filter on
TimeUS, not _timestamp. _timestamp is unix epoch; the log-relative seconds you want are msg.TimeUS / 1e6.
ISBH.instance encodes pre/post-filter. Pre-filter blocks use instance 0..N-1; post-filter blocks (only present with INS_LOG_BAT_OPT bit for post/pre-post) use instance + imu_count. With a 2-IMU mask: 0,1 = pre-filter IMU0/IMU1; 2,3 = post-filter. If only 0,1 appear, you have pre-filter only and cannot measure notch residual — re-fly with INS_LOG_BAT_OPT=2 (post-filter) to get it.ISBH.type: 0 = accel, 1 = gyro.ISBH.mul is a MULT-table index, not a scale factor. Peak frequencies are scale-invariant so they're valid regardless; do not quote PSD magnitudes without resolving mul against the MULT messages — use the calibrated VIBE values for magnitude instead.
Reading the spectrum. The dominant copter peak is almost always the motor/prop fundamental: f_fund_Hz = mean(ESC.RPM) / 60 (e.g. 15,000 RPM → 250 Hz), with harmonics at 2x/3x. Four motors at slightly different RPM spread the fundamental into a band tens of Hz wide. Overlay f_fund and INS_HNTCH_FREQ on the plot.
The harmonic notch is constant-Q, not constant-Hz — the single most common misread. NotchFilter::calculate_A_and_Q() computes the quality factor once from the base INS_HNTCH_FREQ and INS_HNTCH_BW, and every dynamic frequency update reuses the stored _Q (set_center_frequency → init_with_A_and_Q); the bandwidth is never recomputed. So the absolute −3 dB bandwidth scales linearly with the tracked center frequency: BW(f) ≈ BW_base × f / FREQ_base. Concretely BW=10 at a 40 Hz base is Q≈3.7 and becomes ~55 Hz at 220 Hz, ~64 Hz at 256 Hz. Do not flag INS_HNTCH_BW=10 as "too narrow to cover a 40 Hz-wide peak at 250 Hz" — at the tracked frequency it is ~6x wider than its base value. In ESC/RPM/FFT tracking modes (INS_HNTCH_MODE 3/2/4) FREQ is only the floor; the notch follows RPM. Decode INS_HNTCH_OPTS against the Options enum in libraries/Filter/HarmonicNotchFilter.h (DoubleNotch=1, DynamicHarmonic=2, LoopRateUpdate=4, EnableOnAllIMUs=8, TripleNotch=16, TreatLowAsMin=32) — values and the presence of a MultiSource bit differ by branch, so read the enum, don't assume.
The notch cannot fix a vibration-induced altitude problem. The harmonic notch cleans the gyro (and optionally accel) for the control loops. It does not remove the DC bias that high-amplitude accel vibration rectifies onto AccZ (INS_ACC_VRFB_Z territory — see the indoor playbook §4.8). So when high VIBE correlates with an XKF2.AZ bias and EKF-altitude drift, retuning the notch will not help: the fix is mechanical (prop balance, motor-mount integrity, FC soft-mount). Confirm the source frequency with the FFT, then say so plainly rather than recommending notch changes.
Common Message Types
Navigation
| Type | Key Fields | Notes |
|---|
| XKF1 | Roll,Pitch,Yaw,VN,VE,VD,PN,PE,PD | EKF primary output. PD is positive-down. |
| XKF2 | AX,AY,AZ,VWN,VWE | Accel bias, wind estimate |
| XKF3 | IVN,IVE,IVD,IPN,IPE,IPD | Innovations (should be small) |
| XKF4 | SV,SP,SH,SM,SVT,FS,TS,SS | Variances, faults, timeouts |
| ATT | Roll,Pitch,Yaw,DesRoll,DesPitch,DesYaw | Attitude actual vs desired |
| CTUN | Alt,BAlt,DAlt,TAlt,CRt | Alt controller: actual, baro, desired, target, climb rate |
Sensors
| Type | Key Fields | Notes |
|---|
| BARO | Alt,Press,Temp | Barometer |
| GPS | Lat,Lng,Alt,Spd,NSats,HDop | GPS fix data |
| RFND | Dist,Stat,Orient | Rangefinder (Stat: 0=NoData, 4=Good) |
| IMU | AccX,AccY,AccZ,GyrX,GyrY,GyrZ | Raw IMU |
| MAG | MagX,MagY,MagZ | Magnetometer |
Control
| Type | Key Fields | Notes |
|---|
| RCIN | C1-C16 | RC input channels (PWM) |
| RCOU | C1-C14 | Servo/motor outputs (PWM) |
| RATE | RDes,R,ROut,PDes,P,POut,YDes,Y,YOut | PID rate controller |
| PIDR/PIDP/PIDY | Tar,Act,Err,P,I,D,FF,Dmod,SRate,Limit | PID components per axis |
| CTRL | RMSRollP,RMSRollD,RMSPitchP,RMSPitchD,RMSYaw | Controller RMS values |
System
| Type | Key Fields | Notes |
|---|
| MODE | Mode,ModeNum | Flight mode changes |
| EV | Id | Events (10=ARM, 11=DISARM, 18=LAND_COMPLETE, etc.) |
| ERR | Subsys,ECode | Errors (16=EKFCHECK, 12=CRASH_CHECK, etc.) |
| PARM | Name,Value | Parameter changes |
| BAT | Volt,Curr,CurrTot | Battery |
| POWR | Vcc,VServo | Power board |
XKF4 Status Field Reference
- FS (Fault Status): Bitmask of filter faults
- TS (Timeout Status): Bit 0=Pos, 1=Vel, 2=Hgt, 3=Mag, 4=Airspeed, 5=Drag
- SS (Solution Status): NavFilterStatusBit bitmask
- PI: Primary core index
Tips
- Default output limit is 5000 rows. Use
--limit 0 for all data, --decimate N to thin.
- The
compare command aligns data to a 0.1s grid by default. Use --interval 0.02 for higher resolution.
- For EKF altitude, use the
altitude recipe which automatically negates XKF1.PD for you.
--condition uses pymavlink syntax: "MSG.Field==value", "MSG.Field>value", supports and/or.- Use
--sources with both compare and plot for ad-hoc cross-message-type analysis.
- The
stats command supports both --sources "TYPE.Field,..." and --types TYPE --fields F1,F2 syntax.
- Producing a customer-facing PDF report: write the analysis as a markdown file with adjacent PNG plots referenced as
, then convert with pandoc <file>.md -o <file>.pdf --pdf-engine=xelatex -V geometry:margin=2cm -V mainfont="DejaVu Serif" -V monofont="DejaVu Sans Mono". The DejaVu fonts cover Unicode characters (≈, °, arrows) that the default LaTeX font misses; without them xelatex emits "Missing character" warnings and the symbols vanish from the PDF.
Telemetry Log (.tlog) Support
The tool supports MAVLink .tlog files with the same commands as .bin files. Key differences:
- Message names differ: tlog uses MAVLink names (e.g.,
VFR_HUD, GLOBAL_POSITION_INT, GPS_RAW_INT, EKF_STATUS_REPORT, ATTITUDE) rather than DataFlash names (e.g., CTUN, GPS, XKF4, ATT).
- Field names differ: tlog uses MAVLink field names (e.g.,
alt, climb, airspeed) rather than DataFlash names (e.g., Alt, CRt, Aspd). Run overview first to see available types and fields.
- Multiple source systems: tlog contains messages from vehicle, GCS, and peripherals interleaved. Use
--system <id> to filter to the vehicle only. The overview command identifies the vehicle system ID.
- Status text: tlog overview shows all STATUSTEXT messages with severity and timestamp — often the most useful data for crash investigation.
- No EV/ERR messages: tlog doesn't have DataFlash event/error messages. Use STATUSTEXT for equivalent information.
- Recipes may not work directly: The built-in recipes use DataFlash message/field names. For tlog, use
--sources or --types/--fields with MAVLink names instead.
Common tlog message types for crash investigation
python3 .codex/skills/log-analyze/log_extract.py extract <tlog> --types VFR_HUD \
--fields alt,climb,airspeed,groundspeed,heading --system 5
python3 .codex/skills/log-analyze/log_extract.py extract <tlog> --types GLOBAL_POSITION_INT \
--fields lat,lon,alt,relative_alt,vx,vy,vz --system 5
python3 .codex/skills/log-analyze/log_extract.py extract <tlog> --types GPS_RAW_INT \
--fields fix_type,lat,lon,alt,satellites_visible --system 5
python3 .codex/skills/log-analyze/log_extract.py extract <tlog> --types EKF_STATUS_REPORT \
--fields flags,velocity_variance,pos_horiz_variance,pos_vert_variance,compass_variance --system 5
python3 .codex/skills/log-analyze/log_extract.py extract <tlog> --types NAV_CONTROLLER_OUTPUT \
--fields nav_roll,nav_pitch,alt_error,aspd_error,wp_dist --system 5
python3 .codex/skills/log-analyze/log_extract.py extract <tlog> --types ATTITUDE \
--fields roll,pitch,yaw --system 5
python3 .codex/skills/log-analyze/log_extract.py plot <tlog> \
--sources "VFR_HUD.alt,VFR_HUD.climb" --output /tmp/alt.png --system 5
