resolve-rip

name	resolve-rip
description	Resolve a RIP-relative address from a disassembled x86-64 instruction

/probe:rip

Resolve a RIP-relative address from a disassembled instruction.

When to use

You see a disassembled instruction like:

mov rax, [rip+0x1A2B3C]     ; loads a global variable
lea rcx, [rip+0x5678]        ; loads the address of a string or struct
call 0x7FF612345678           ; calls a function (already resolved by Zydis)

The [rip+disp32] addressing means the target address depends on where the instruction is. You need to resolve it to an absolute address.

The formula

target = instruction_address + instruction_length + displacement

Where:

• instruction_address = the address shown in the disassembly
• instruction_length = number of bytes in the instruction (sum up the hex bytes)
• displacement = the signed 32-bit value encoded in the instruction

Common instruction patterns

MOV reg, [RIP+disp32] — Load a global pointer

48 8B 05 XX XX XX XX     ; MOV RAX, [RIP+disp32]

• instruction_length = 7
• displacement starts at byte 3 (offset +3)
• target = addr + 7 + int32_at(addr + 3)

LEA reg, [RIP+disp32] — Load address of string/data

48 8D 0D XX XX XX XX     ; LEA RCX, [RIP+disp32]
48 8D 15 XX XX XX XX     ; LEA RDX, [RIP+disp32]
4C 8D 05 XX XX XX XX     ; LEA R8,  [RIP+disp32]

• instruction_length = 7
• displacement starts at byte 3
• target = addr + 7 + int32_at(addr + 3)

CALL rel32 — Relative function call

E8 XX XX XX XX           ; CALL rel32

• instruction_length = 5
• displacement starts at byte 1
• target = addr + 5 + int32_at(addr + 1)

JMP rel32 — Relative jump

E9 XX XX XX XX           ; JMP rel32

• Same as CALL: target = addr + 5 + int32_at(addr + 1)

Conditional jump rel32

0F 84 XX XX XX XX        ; JE rel32
0F 85 XX XX XX XX        ; JNE rel32

• instruction_length = 6
• displacement starts at byte 2
• target = addr + 6 + int32_at(addr + 2)

Steps

1. Disassemble the instruction:

   probe_disassemble address=<addr> count=1
   

   Note the instruction bytes and text.

2. Read the raw displacement (4 bytes, little-endian signed):

   probe_read address=<addr + rip_offset> size=4
   

   Where rip_offset is where the 4-byte displacement starts (3 for MOV/LEA, 1 for CALL/JMP, 2 for Jcc).

3. Calculate the target:

   target = instruction_address + instruction_length + signed_displacement
   

4. Verify the target:

   probe_read_pointer address=<target>    ; if it's a global pointer
   probe_read_string address=<target>     ; if it's a string reference
   probe_disassemble address=<target>     ; if it's a function call
   

Shortcut: use --resolve

The probe_pattern_scan command has a --resolve flag that does this automatically:

probe_pattern_scan pattern="48 8B 05 ?? ?? ?? ??" module="client.dll" resolve=3

This scans for the pattern and resolves the RIP-relative address at offset 3, returning the absolute target.

Signed displacement reminder

The displacement is a signed 32-bit integer. Negative values mean the target is BEFORE the instruction:

• FF FF FF E0 = -32 in signed int32 → target is 32 bytes before (instruction_address + instruction_length - 32)
• 00 00 10 00 = 4096 → target is 4096 bytes after

Always treat the 4 bytes as signed when calculating.