Manage, troubleshoot, and harden OPNsense and pfSense firewalls via SSH. Both are FreeBSD-based,
pf-powered firewall distributions - most concepts, commands, and patterns apply to both.
Target versions (May 2026):
OPNsense CE: 26.1.7 (current Community Edition stable, "Witty Woodpecker"; CE ships odd quarters .1/.7). Business Edition is 26.4.x (even quarters .4/.10) - do not quote the BE number as the CE version
pfSense CE: 2.8.1 / pfSense Plus: 26.03
CrowdSec: v1.7.7
When to use
Managing or troubleshooting OPNsense and pfSense firewalls over SSH
Reviewing pf rules, NAT, CARP, Unbound, WireGuard, CrowdSec, or pfBlockerNG on these appliances
Configuring VLANs, CARP HA failover, or interface assignments on firewall appliances
Debugging connectivity between networks or VLANs routed through OPNsense/pfSense
Hardening BSD firewall appliances and validating safe remote-change workflows
When NOT to use
Linux networking, reverse proxies, VPN setup, or nftables work outside firewall appliances - use networking
Cloud firewall rules, WAF configuration, or AWS/GCP/Azure network ACLs - use networking or the relevant IaC skill (terraform, ansible)
General shell scripting or local shell behavior outside the BSD firewall context - use command-prompt
Fleet-wide configuration management via playbooks - use ansible
Offensive testing, exploitation, or post-exploitation - use lockpick
Application-level security review or dependency scanning - use security-audit
AI Self-Check
Before returning any firewall commands, verify:
Platform confirmed (OPNsense vs pfSense) - commands differ between them
No commands that could lock out SSH or management access
Config backup taken (or reminded) before destructive changes
pfctl rules tested with -n (dry run) before applying
Service names correct for the target platform (configctl vs service)
Plugin names use correct prefix (os-* for OPNsense, unprefixed for pfSense)
CARP changes target the master node, not the backup
Shell syntax is POSIX sh (heredoc), not bash/zsh (csh/tcsh is the default shell on both)
No firmware or plugin updates without explicit user confirmation
Blast radius stated for any change affecting network connectivity
DNS impact considered - changes to Unbound, DHCP, or firewall rules on port 53 can
break name resolution for all clients on affected VLANs
CrowdSec/pfBlockerNG checked when diagnosing blocks - bans look identical to firewall
drops from the client side
VLAN interface assigned before adding rules - unassigned VLANs pass no traffic through
the firewall even if the trunk is tagged correctly
Current source checked: dated versions, CLI flags, API names, and support windows are verified against primary docs before repeating them
Hidden state identified: local config, credentials, caches, contexts, branches, cluster targets, or previous runs are made explicit before acting
Verification is real: final checks exercise the actual runtime, parser, service, or integration point instead of only linting prose or happy paths
: overlapping skills, trigger terms, and "When NOT to use" boundaries are checked before returning guidance
Performance
Prefer rule ordering that rejects high-volume unwanted traffic early and keeps expensive inspection scoped.
Use aliases/tables for large address sets instead of expanding repetitive rules.
Check state table, DNSBL, IDS/IPS, and plugin load before blaming WAN latency.
Best Practices
Export configuration before rule, NAT, VPN, CARP, or package changes.
Make HA changes one node at a time and verify CARP state before touching the peer.
Keep emergency console or out-of-band access available for management-plane changes.
Workflow
Step 1: Detect platform
If the platform is not obvious from context, ask the user which one they're running before
issuing commands. Identify the target device explicitly - never assume which firewall you're
talking to. Key differences at a glance:
OPNsense
pfSense
Base OS
FreeBSD (migrated from HardenedBSD in 2021)
FreeBSD
Config path
/conf/config.xml
/cf/conf/config.xml
Service control
configctl service restart <svc>
pfSsh.php playback svc restart <svc> or service <svc> restart
Plugin prefix
os-<name> (e.g., os-wireguard)
No prefix (e.g., pfSense-pkg-WireGuard)
PHP shell
N/A
pfSsh.php (interactive PHP shell)
Quick rule add
N/A
easyrule pass wan tcp <src> <dst> <port>
IP blocking
CrowdSec (os-crowdsec)
pfBlockerNG
Root shell
csh
tcsh (same heredoc workaround applies)
IDS/IPS config
/tmp/suricata_*.log, eve.json
/var/log/suricata/suricata.log, eve.json
Firmware CLI
configctl firmware check/status
pkg-static update + GUI
Template engine
configd + configctl template
PHP-generated configs
REST API
Yes (/api/, key/secret auth)
Yes (similar, different endpoints)
Licensing
Free, open source
CE: free but slower updates; Plus: $129/yr on non-Netgate HW
Release cadence
Bi-weekly, fixed schedule
Irregular, Netgate hardware prioritized
2026 status: OPNsense is the clear choice for new deployments. pfSense CE gets slower updates and zero priority; Plus costs $129/year on non-Netgate hardware. Migration from pfSense to OPNsense has no automated path - expect ~60% clean config transfer, manual rebuild for NAT rules, VPN, and DNS forwarder settings.
When platform is unknown, these commands work on both:
For major upgrades on virtualized firewalls, pair config backup with a hypervisor snapshot
Skip this step only for read-only operations (diagnostics, log review, status checks).
Step 3: Execute the task
Apply changes using the platform-appropriate commands. Refer to the domain sections below
and the reference files for specifics. For any change that affects connectivity:
Test pfctl rules with -n (dry run) before applying
State the blast radius ("this will drop all VPN tunnels for ~30s")
On HA pairs, always change on the master node and let XMLRPC sync propagate
Step 4: Verify
After every change, confirm the firewall is healthy:
Connectivity: can you still reach the device? Can clients reach the internet?
Logs: check /var/log/filter.log, service logs, and CrowdSec/Suricata if active
Service status: configctl service list (OPNsense) or service -e (pfSense)
State table: pfctl -si | grep entries - watch for unexpected drops or state exhaustion
Quick Task Procedures
Creating a firewall rule (VLAN to server)
Identify the interface the traffic originates from (e.g., opt1 for VLAN 50)
Confirm the VLAN interface is assigned: ifconfig must show the VLAN interface UP. If the VLAN is not assigned to an OPNsense/pfSense interface yet (Interfaces > Assignments), it cannot have rules - assign it first.
Check existing rules: pfctl -sr | grep <iface> - new interfaces have no rules (implicit deny all). Confirm the baseline before adding anything so you know exactly what you're changing.
Create aliases for source subnet and destination server (keeps rules readable):
OPNsense API: curl -X POST -u key:secret https://<fw>/api/firewall/alias/addItem -d '{"alias":{"name":"WebServer","type":"host","content":"10.0.1.100"}}'
OPNsense CLI: configctl template reload OPNsense/Filter (after editing alias via API or XML). To verify the alias was created: configctl template list | grep Alias, then confirm with pfctl -t WebServer -T show.
pfSense: easyrule doesn't support aliases - use GUI or edit /cf/conf/config.xml directly
Add a pass rule on the VLAN interface (not WAN - pf evaluates rules on the interface where traffic enters): source = alias, destination = server alias, port = 443
Place the allow rule above any block-all rule for that interface (OPNsense/pfSense interface rules use quick by default, so the FIRST matching rule wins - put the specific allow above the broad block)
Test: pfctl -n -f /tmp/rules.debug (OPNsense) to dry-run before applying
Verify: pfctl -sr | grep <alias> to confirm the rule is active
Creating a block rule (isolate IoT VLAN)
Block IoT devices from reaching internal networks while allowing internet access:
Identify the IoT VLAN interface (e.g., opt3 for VLAN 30)
Create an alias for RFC1918 ranges: name RFC1918, type Network, content 10.0.0.0/8, 172.16.0.0/12, 192.168.0.0/16
Add a block rule on the IoT interface: source = IoT subnet, destination = RFC1918 alias, action = block. This prevents IoT from reaching any internal network.
Add a pass rule below it: source = IoT subnet, destination = any, ports = 53 (DNS), 443 (HTTPS). This allows internet access for the permitted services.
Rule order matters: with quick (the OPNsense/pfSense default) the FIRST matching rule wins, so the RFC1918 block must come before the broad pass rule - otherwise the pass matches first and lets the traffic through.
Test and apply as above: pfctl -n -f /tmp/rules.debug, then configctl filter reload
Troubleshooting connectivity after VLAN changes
Work through these steps in order. Do not skip ahead or assume the root cause - each step eliminates one layer. The most common failure is a missing outbound NAT rule, not a firewall rule. Also check CrowdSec (cscli decisions list) and Suricata early - their blocks look identical to firewall drops from the client side.
Prerequisite: the VLAN must be assigned to a firewall interface before it can have rules, DHCP, or NAT. In OPNsense: Interfaces > Assignments > add the VLAN, then enable it and set its IP. In pfSense: Interfaces > Interface Assignments. An unassigned VLAN passes no traffic through the firewall even if the parent trunk is tagged correctly.
Interface assigned and UP?ifconfig - is the VLAN interface listed and UP? If not: assign it (see prerequisite above). If listed but DOWN: enable it in the GUI or check the parent interface.
Blocklist check: cscli decisions list (OPNsense CrowdSec) or check pfBlockerNG deny logs (pfSense) - CrowdSec and pfBlockerNG bans look identical to firewall drops from the client side. Clear false positives before digging into rules.
Services running?configctl service list (OPNsense) or service -e (pfSense) - confirm DHCP, DNS (Unbound), and the packet filter are running. A stopped DHCP server on the new VLAN means clients never get an IP.
Rules present?pfctl -sr - any pass rules on the new VLAN interface? New interfaces have no rules by default (deny all).
NAT configured? Check outbound NAT rules include the new VLAN subnet. On OPNsense: Firewall > NAT > Outbound. Missing outbound NAT is the #1 cause of "VLAN can't reach internet."
DNS working?drill google.com @<firewall-ip> from a VLAN client. If this fails but ping to 8.8.8.8 works, it's a DNS issue, not a firewall rule.
Packet capture: tcpdump -ni <vlan-iface> host <client-ip> - are packets arriving at the firewall?
Reading tcpdump output: each line shows timestamp src > dst: proto. Look for: (a) request packets from the client arriving on the VLAN interface, (b) reply packets going back. If you see requests but no replies, the firewall is blocking or NAT is missing. If you see no packets at all, the issue is below the firewall - check VLAN tagging, trunk config, and switch ports. Use -v for header details or -X for payload hex when deeper inspection is needed.
If packets arrive but no response: the rule or NAT is the problem. If no packets: the VLAN trunk, switch tagging, or interface assignment is wrong - check the physical/virtual layer before touching firewall config.
FreeBSD Mental Model
Read references/platform-and-operations.md for the detailed FreeBSD shell model, key commands,
config system, REST API, IPv6 gotchas, SOPs, and recovery procedures.
Treat both platforms as FreeBSD appliances, not Linux hosts.
For anything beyond trivial SSH one-liners, prefer piping a POSIX sh heredoc instead of fighting csh or tcsh.
Guard non-zero informational commands with ; true when running checks in parallel.
Operations and Common Tasks
Identify the target device explicitly before changing anything.
Back up config before risky changes or upgrades.
Check plugin or package layers early because they often explain traffic behavior that looks like a firewall-rule problem.
Treat firmware, plugin, backup, and HA work as operational procedures, not casual single commands.
Use references/plugins.md for plugin specifics and references/hardening.md for hardening and CARP guidance.
references/plugins.md - operational guidance for common OPNsense plugins (CrowdSec,
WireGuard, Suricata, HAProxy, ACME, FRR, etc.). For pfSense package equivalents, map
concepts using the platform comparison table above.
references/hardening.md - comprehensive hardening checklist. OPNsense-focused but most
items apply to pfSense with equivalent settings in its GUI/config.
Output Contract
See skills/_shared/output-contract.md for the full contract.
Skill name: FIREWALL-APPLIANCE
Deliverable bucket:audits
Mode: conditional. When invoked to analyze, review, audit, or improve existing repo content, emit the full contract - boxed inline header, body summary inline plus per-finding detail in the deliverable file, boxed conclusion, conclusion table - and write the deliverable to docs/local/audits/firewall-appliance/<YYYY-MM-DD>-<slug>.md. When invoked to answer a question, teach a concept, build a new artifact, or generate content, respond freely without the contract.
Severity scale:P0 | P1 | P2 | P3 | info (see shared contract; only used in audit/review mode).
Related Skills
networking - for Linux reverse proxies, VPNs, DNS, nftables, and cloud network ACLs (AWS/GCP/Azure security groups, WAF rules) outside BSD firewall appliances
terraform - for provisioning and managing cloud firewall rules, WAF policies, and network ACLs as infrastructure-as-code
ansible - for fleet-wide firewall automation or playbook-based configuration management
command-prompt - for general shell scripting and local shell behavior; this skill covers the FreeBSD firewall context
security-audit - for defensive security review of application code and supply chain, rather than firewall administration
lockpick - for authorized offensive testing and post-exploitation, not defensive firewall operations
Rules
These exist because bricking a firewall remotely means driving to wherever it is.
Never modify rules that could lock out SSH access. If the change touches the SSH port or the
management interface, triple-check the rule order and confirm with the user.
Never disable the LAN interface or change its IP without explicit confirmation and a rollback
plan.
Never apply firmware or plugin updates without asking first - updates can reboot the device
and may require physical console access if something goes wrong.
Always confirm destructive changes: rule deletions, service disables, plugin removals,
state table flushes (pfctl -Fa).
Estimate blast radius: if a change could cause network disruption beyond the target device,
warn the user with specifics (e.g., "this will drop all VPN tunnels for ~30s").
OPNsense CrowdSec: don't delete decisions or bouncers without understanding why they exist.
A ban that looks wrong might be catching a real attack.
pfSense pfBlockerNG: don't disable feed lists without understanding what they block.
Review the deny logs before removing feeds.
HA/CARP (both platforms): never make config changes directly on the backup node - XMLRPC
sync from master will overwrite them. Always change on master and let sync propagate.
pfSense easyrule: convenient but creates rules without descriptions. Document what you
added and why. Consider using the GUI or config.xml for permanent rules instead.
Routing overlap checked
Spec claims verified: claims about tool behavior, output contracts, or repo conventions are checked against current docs, scripts, or skill files
Platform/version checked: OPNsense, pfSense, FreeBSD, pf, and plugin commands match the appliance version
