Design and analysis of combinational and sequential digital circuits using Boolean algebra, truth tables, K-maps, CMOS gate implementation, flip-flops, registers, counters, and finite state machines. Covers De Morgan's theorems, canonical sum-of-products and product-of-sums forms, minimization techniques, propagation delay, setup and hold times, metastability, synchronous design discipline, and FSM encoding. Use when designing, minimizing, verifying, or debugging any circuit whose signals take only discrete logic values.
Installer avec Codex ou Claude Copiez ce prompt, collez-le dans Codex, Claude ou un autre assistant, puis laissez-le vérifier la page du skill et l'installer pour vous.
Une commande directe contourne le prompt de vérification. Examinez la source avant de l'exécuter.
Design and analysis of combinational and sequential digital circuits using Boolean algebra, truth tables, K-maps, CMOS gate implementation, flip-flops, registers, counters, and finite state machines. Covers De Morgan's theorems, canonical sum-of-products and product-of-sums forms, minimization techniques, propagation delay, setup and hold times, metastability, synchronous design discipline, and FSM encoding. Use when designing, minimizing, verifying, or debugging any circuit whose signals take only discrete logic values.
Digital logic is the subset of electronics where signal values are restricted to a small number of discrete levels (usually two: logic 0 and logic 1). This restriction buys enormous simplification — Boolean algebra replaces differential equations, truth tables replace transfer functions — at the cost of needing to worry about timing, glitches, metastability, and the difference between what the logic says and what the silicon actually does. This skill covers combinational and sequential design in the order a designer typically needs them.
Agent affinity: kilby (integrated logic and gate-level implementation), noyce (planar process and mass production of logic families)
Digital logic rests on Boolean algebra, where variables take values in {0, 1} and three operations dominate: AND (conjunction, written A * B or A∧B), OR (disjunction, A + B or A∨B), and NOT (negation, A' or ¬A). Several identities make manipulation tractable:
Identity
Name
A + 0 = A, A * 1 = A
Identity
A + 1 = 1, A * 0 = 0
Domination
A + A = A, A * A = A
Idempotent
(A')' = A
Double negation
A + A' = 1, A * A' = 0
Complement
A + B = B + A, A * B = B * A
Commutative
(A + B) + C = A + (B + C)
Associative
A * (B + C) = AB + AC
Distributive
(A + B)' = A' * B'
De Morgan
(A * B)' = A' + B'
De Morgan
De Morgan's theorems are the lever that converts NAND-only gate sets to full Boolean expressiveness and back. In CMOS, NAND and NOR are the natural primitives because they come for free from the complementary pull-up/pull-down network.
Technique 1 — Truth Tables and Canonical Forms
Truth table. Exhaustively list every input combination and the desired output. For n inputs there are 2^n rows.
Sum of products (SoP). Write the function as the OR of all minterms (product terms) corresponding to rows where the output is 1. Example: F(A, B, C) = A'BC + AB'C + ABC'.
Product of sums (PoS). Write the function as the AND of all maxterms (sum terms) corresponding to rows where the output is 0, with each variable negated.
Worked example. A three-input majority function has output 1 when at least two inputs are 1. Truth table:
A
B
C
F
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
1
1
0
0
0
1
0
1
1
1
1
0
1
1
1
1
1
The SoP is F = A'BC + AB'C + ABC' + ABC, which simplifies to AB + AC + BC.
Technique 2 — Karnaugh Map (K-map) Minimization
A K-map is a two-dimensional arrangement of a truth table where physically adjacent cells differ in exactly one variable. Groups of 1s in powers of two (1, 2, 4, 8...) correspond to product terms where the variables that change within the group drop out.
Procedure. Draw the K-map, circle the largest possible groups of 1s that cover every 1 exactly (groups may overlap and may wrap around edges), write each group as a product term, OR them together.
Worked example (majority function above). The K-map has four 1s at (ABC) = 011, 101, 110, 111. The groupings produce AB, AC, and BC. The minimal SoP is F = AB + AC + BC — confirming the algebraic simplification above.
Limits. K-maps become impractical above five variables. For larger functions use the Quine-McCluskey tabular method or hand it to a synthesis tool.
Technique 3 — CMOS Gate Implementation
In CMOS, every gate has a complementary pull-up (PMOS) and pull-down (NMOS) network. The pull-down conducts when the pull-up does not, and vice versa, so the output is always connected to either V_DD or GND through a low-resistance path (except during transitions). Static power is near zero — dynamic power dominates, set by C * V^2 * f.
NAND gate. Two PMOS in parallel pull up, two NMOS in series pull down. Output is LOW only when both inputs are HIGH.
NOR gate. Two PMOS in series pull up, two NMOS in parallel pull down. Output is LOW if either input is HIGH.
Why NAND and NOR are preferred. Inverting gates are structurally natural in CMOS. An AND gate is a NAND followed by an inverter — two levels of logic for what could have been one. Good synthesis tools automatically convert AND/OR expressions to NAND/NOR.
Technique 4 — Combinational Building Blocks
Block
Function
Typical use
Multiplexer
Select one of N inputs based on select lines
Data path routing, ROM readout
Decoder
One-hot output indicating which of N states is active
Address decoding, FSM state output
Encoder
Priority encoding of one-hot input to binary
Interrupt priority, keypad scanning
Adder
Binary addition with carry propagation
Arithmetic unit core
Comparator
Output 1 if A > B, A = B, or A < B
Sorting, control logic
Parity generator
XOR tree producing even or odd parity
Error detection
These blocks are the lego bricks of digital design. Most real circuits are compositions of multiplexers and decoders with a sprinkle of arithmetic.
Technique 5 — Flip-Flops and Registers
D flip-flop. On the active edge of the clock, captures the value at the D input and holds it on Q until the next active edge. The most commonly used sequential primitive.
JK flip-flop. Extension of SR latch that toggles when both J and K are high. Rarely used in modern design; D flip-flops plus combinational feedback can express the same behavior.
Register. An array of D flip-flops sharing a common clock, used to hold a multi-bit value.
Setup and hold times. A flip-flop requires its input to be stable for t_setup before the clock edge and t_hold after. Violating either causes metastability — the output takes an unbounded time to settle to a valid logic level. This is the central timing constraint in synchronous design.
Propagation delay. After the clock edge, the output takes t_CQ to reflect the captured value. All timing budgets are sums of t_CQ + combinational delay + t_setup, which must be less than the clock period.
Technique 6 — Finite State Machines
Definition. A finite state machine has a finite set of states, a set of input signals, a transition function from (state × inputs) to next state, and an output function from state (Moore) or (state × inputs) (Mealy).
Design procedure.
Identify the states.
Draw a state transition diagram.
Encode the states in binary (binary, one-hot, gray code, etc.).
Write the next-state logic as a combinational block.
Write the output logic.
Implement state registers as D flip-flops.
State encoding trade-offs:
Encoding
Bits for N states
Next-state complexity
Output complexity
Binary
ceil(log2(N))
Complex
Complex
One-hot
N
Simple
Simple
Gray
ceil(log2(N))
Medium
Complex
One-hot is usually preferred for FPGAs (flip-flops are cheap) and binary for ASICs (routing and area matter). The reason Kilby's original integrated circuit mattered so much is that these trade-offs only became economic when hundreds of gates per chip were possible.
Technique 7 — Synchronous Design Discipline
The single most important rule in practical digital design: every flip-flop in the system should be clocked by the same clock signal, or by clock signals derived from a common root through known-good synchronization paths.
Why. Multiple independent clocks create clock domain crossings where metastability can occur. Asynchronous resets create their own release-time issues. Gated clocks hide timing from the synthesis tool.
The synchronous discipline:
One clock domain unless absolutely necessary.
Synchronize any asynchronous input with at least two flip-flops in series (double-flopping).
Use synchronous reset rather than asynchronous where possible.
Do not gate clocks in RTL; let the synthesis tool insert clock gates if power demands it.
Make every FSM have a defined reset state.
Common Mistakes
Mistake
Why it fails
Fix
Combinational loop
Latches form; timing indeterminate
Break the loop with a flip-flop
Missing else branch in RTL
Unintended latch inferred
Always assign every signal in every path
Asynchronous handshakes without synchronizers
Metastability propagates
Double-flop the incoming signal
State machines with undefined reachable states
Hangs after power-up glitch
Define a default next-state assignment
Gated clocks in RTL
Synthesis complications, timing violations
Use clock-enable inputs instead
Mixing blocking and nonblocking assignments
Race conditions in simulation
Blocking for combinational, nonblocking for sequential
Depending on propagation delay for pulse width
Varies with process, voltage, temperature
Generate pulse widths with counters
Cross-References
microcontroller-firmware skill: Uses digital logic results inside the MCU — GPIO, PWM, UART, SPI, I2C are all synchronous FSMs internally.
kilby agent: Primary agent for integrated circuit topology and logic family questions.
noyce agent: Primary agent for monolithic process and practical fabrication questions.
signal-processing-dsp-basics skill: Takes digital values and processes them as samples of a continuous signal.
References
Harris, D. & Harris, S. (2022). Digital Design and Computer Architecture. 3rd ed. Morgan Kaufmann.
Wakerly, J. F. (2018). Digital Design: Principles and Practices. 5th ed. Pearson.
Mano, M. M. & Ciletti, M. D. (2018). Digital Design. 6th ed. Pearson.
Horowitz, P. & Hill, W. (2015). The Art of Electronics. 3rd ed. Cambridge University Press, chapters 10-11.
Kilby, J. S. (1976). "Invention of the integrated circuit." IEEE Transactions on Electron Devices, 23(7), 648-654.
