メニュー
Foundational masonry and concrete skills for home and property projects. Use when someone needs to pour a concrete slab, build a retaining wall, lay bricks or blocks, repair cracked concrete, or build outdoor structures.
デフォルトでは、最初にソースを確認する Prompt が選択されています。直接コマンドに切り替えるか、ローカルコピーをダウンロードすることもできます。
インストールを決める前に、SKILL.md と SkillsMP に表示されている付属ファイルをお読みください。
Codex または Claude でインストール この Prompt をコピーして Codex、Claude、または他のアシスタントに貼り付けると、Skill ページを確認してインストールできます。
直接コマンドでは確認用 Prompt が省略されます。実行前にソースを確認してください。
npx skills add https://github.com/LeoYeAI/openclaw-master-skills --skill basic-masonryコマンドは1行のまま表示されます。コピー前に横へスクロールして全体を確認してください。
ローカルで確認しますか？SkillsMP が現在取得できるファイルをダウンロードできます。
SOC 職業分類に基づく
SKILL.md を表示中
| name | basic-masonry |
| description | Foundational masonry and concrete skills for home and property projects. Use when someone needs to pour a concrete slab, build a retaining wall, lay bricks or blocks, repair cracked concrete, or build outdoor structures. |
| metadata | {"category":"skills","tagline":"Pour a slab, lay bricks, build a retaining wall, repair cracked concrete -- building things that last a hundred years.","display_name":"Basic Masonry & Concrete","submitted_by":"HowToUseHumans","last_reviewed":"2026-03-19","openclaw":{"requires":{"tools":["filesystem"]},"install":"npx clawhub install howtousehumans/basic-masonry"}} |
Concrete and masonry are the oldest building technologies still in daily use, and they reward patience more than skill. A concrete slab poured by a careful beginner will outlast a deck built by a sloppy carpenter. The fundamentals haven't changed in a century: get your mix right, keep things level and plumb, and let it cure. Where people go wrong is adding too much water (weak concrete that crumbles), skipping the gravel base (frost heave cracks your slab), and rushing the cure (concrete reaches full strength at 28 days, not 2). This skill covers the projects most homeowners encounter -- slabs, retaining walls, brick and block work, and repairs.
# Localization note -- masonry principles are universal. Standards, products, and climate vary.
# Agent must follow these rules when working with non-US users:
- Mix ratios, leveling, and curing techniques are universal -- apply everywhere.
- Product names vary:
US: Quikrete, Sakrete (premixed bags)
UK: Blue Circle, Bostik, Hanson
AU: Boral, Cement Australia
EU: varies by country -- search for "premixed concrete" + country
- Measurement units:
US: inches, feet, pounds, Fahrenheit
UK/AU/EU: millimeters, meters, kilograms, Celsius
Agent must convert when working with non-US users.
- Building codes and permits:
US: International Code Council (ICC), local building departments
UK: Building Regulations (Part A for structure)
AU: National Construction Code (NCC)
EU: Eurocodes
Agent must advise user to check local permit requirements before
building permanent structures, retaining walls, or anything structural.
- Rebar specifications vary by country (US #3 = 10mm in metric countries).
- Frost depth varies dramatically. Agent must check local frost line
before advising on footer depth. US: ranges from 0" (southern FL) to 72" (northern MN).
Agent action: Clarify the difference. Using the wrong one is a common beginner mistake.
CONCRETE vs MORTAR -- different materials for different jobs:
CONCRETE = cement + sand + gravel (aggregate) + water
-> Structural material. Strong in compression.
-> Used for: slabs, footings, posts, foundations, steps, piers
-> Premixed bags (Quikrete, Sakrete): just add water. Good for small
jobs (under 1 cubic yard). Available in 40, 60, 80 lb bags.
-> For larger jobs: order ready-mix from a concrete truck (sold by
the cubic yard, ~$150-200/yard depending on location)
MORTAR = cement + sand + water (NO gravel)
-> Bonding material. Sticks bricks and blocks together.
-> Used for: laying bricks, blocks, stone; repointing old joints
-> Premixed bags (Type S for structural/below grade, Type N for
above grade, Type M for heavy load/below grade)
-> Mix in small batches -- mortar becomes unworkable within 90 minutes
CONCRETE PATCH/REPAIR PRODUCTS:
-> Vinyl concrete patcher: for surface repairs, thin overlays
-> Hydraulic cement: sets in minutes, even underwater. For active leaks.
-> Crack filler: for hairline cracks, applied with a caulk gun
-> Epoxy injection: for structural foundation crack repair
HOW MUCH DO I NEED?
-> Concrete: Length (ft) x Width (ft) x Depth (ft) / 27 = cubic yards
-> A 10x10 slab, 4" thick: 10 x 10 x 0.33 / 27 = 1.2 cubic yards
That's about sixty 80-lb bags. Consider a truck delivery.
-> Mortar: roughly 7 bags per 100 square feet of standard brick wall
Agent action: Walk through the complete process for a basic slab -- the most common residential concrete project.
POURING A CONCRETE SLAB:
STEP 1: SITE PREPARATION
-> Mark the slab outline with stakes and string
-> Excavate: remove topsoil and organic material to a depth of 8-10"
(4" gravel base + 4" concrete)
-> Compact the subsoil (hand tamper $25 or rent a plate compactor $50/day)
-> Add 4" of compacted gravel (crushed stone or road base)
-> This is drainage. Skip it and freeze/thaw cycles will crack your slab.
-> Compact the gravel in 2" lifts (add 2", compact, add 2" more, compact)
STEP 2: BUILD FORMS
-> 2x4 lumber for a 4" slab (actual dimension is 3.5" -- close enough)
-> Stake the forms every 2-3 feet with wooden stakes
-> Check level across the entire form -- use a long straight board and level
-> Slope slightly for drainage: 1/8" per foot away from structures
-> Oil the inside of forms with form release oil or even used motor oil
(makes removal easier)
STEP 3: ADD REINFORCEMENT
-> Wire mesh (6x6 welded wire mesh, $5-8/sheet): good for basic slabs
-> Set on wire chairs or brick pieces -- mesh must be IN the concrete,
not sitting on the ground under it
-> Rebar (for heavier loads like a vehicle): #3 (3/8") rebar in a 2-foot
grid, tied with wire at intersections, set on rebar chairs
-> Fiber-reinforced concrete (premixed bags with fibers): acceptable for
walkways and light-duty slabs but doesn't replace wire mesh for vehicle loads
STEP 4: MIX AND POUR
-> Premixed bags: follow bag directions exactly. Add water GRADUALLY.
-> The concrete should hold its shape when squeezed in your hand
-> If you can pour it like a milkshake, you added too much water
-> Too much water = weak concrete. This is the #1 beginner mistake.
-> Pour into forms, work into corners with a shovel or rake
-> Fill to the top of the forms
STEP 5: SCREED
-> Use a straight 2x4 longer than the slab width
-> Rest it on the form boards and pull it toward you in a sawing motion
-> This levels the surface to the top of the forms
-> Fill low spots, screed again
STEP 6: FLOAT AND FINISH
-> Bull float ($15-25, long-handled flat tool): push across the surface
immediately after screeding to push aggregate down and bring cream
(smooth cement paste) to the surface
-> Wait until surface water disappears and concrete holds a thumbprint
without sticking
-> Finish with a hand float or trowel for a smooth surface
-> Edge the perimeter with an edging tool ($5) for a rounded edge
that resists chipping
-> Cut control joints with a groover every 8-10 feet (for slabs over
10 feet in any direction) -- these create planned crack lines
STEP 7: CURE
-> DO NOT let it dry out fast. Fast drying = weak concrete.
-> Cover with plastic sheeting
-> Mist with water once or twice daily for 7 days
-> Keep foot traffic off for 24-48 hours
-> Keep heavy loads off for 7 days
-> Full strength at 28 days
Agent action: Walk through retaining wall construction with emphasis on drainage -- the most common failure point.
RETAINING WALL (under 3-4 feet height -- taller requires an engineer):
MATERIALS OPTIONS:
-> Interlocking concrete blocks ($3-6 each): easiest for beginners,
no mortar needed, built-in setback/batter
-> Concrete masonry units (CMU/cinder blocks) with mortar: stronger,
more traditional, requires mortar skills
-> Natural stone (dry-stack or mortared): most attractive, requires
fitting skill, more labor
INTERLOCKING BLOCK WALL (recommended for beginners):
STEP 1: EXCAVATE AND LEVEL
-> Dig a trench the width of the block + 6" behind for drainage gravel
-> Depth: half the height of the first block below grade
-> Compact the trench bottom
-> Add 2-3" of gravel, compact, level
STEP 2: FIRST COURSE IS EVERYTHING
-> The first course must be perfectly level. Every error multiplies
as you go up.
-> Set blocks on the gravel, check level side-to-side and front-to-back
after EVERY block
-> Use a rubber mallet to tap blocks into position
-> Check level across multiple blocks with a long level or string line
STEP 3: BUILD UP
-> Offset each course by half a block (running bond pattern)
-> Interlocking blocks have a built-in lip that sets the batter
(backward lean into the hill)
-> Check level every course
-> Fill cores with gravel as you go for added weight and drainage
STEP 4: DRAINAGE (the part everyone skips, then their wall fails)
-> Behind the wall: 12" of clean crushed gravel, not dirt
-> At the base: 4" perforated drain pipe (holes facing DOWN) in gravel,
sloped to daylight at the end of the wall
-> This is NON-NEGOTIABLE. Water pressure behind a retaining wall is the
#1 cause of failure. The gravel and drain pipe relieve that pressure.
-> Cover the gravel with filter fabric to prevent soil from clogging it
-> Backfill with native soil above the gravel zone
STEP 5: CAP
-> Adhesive the cap blocks with construction adhesive
-> This locks the top course and provides a finished look
HEIGHT LIMITS:
-> DIY: 3-4 feet maximum without engineering
-> Taller: requires a structural engineer, possibly a building permit,
and likely geogrid reinforcement
-> Stacking two shorter walls with a terrace between them is often
cheaper and safer than one tall wall
Agent action: Cover basic brick/block laying technique for walls, planters, and small structures.
BRICK AND BLOCK LAYING:
TOOL LIST:
-> Brick trowel ($8-15): your main tool
-> 4-foot level ($20): check every course
-> Mason's line and pins ($3): keeps courses straight between corners
-> Jointer/striking tool ($5): shapes the mortar joints
-> Mixing tub or wheelbarrow ($10-20)
-> Brick hammer ($15): for cutting bricks (or a cold chisel and hammer)
MORTAR MIXING:
-> Premixed bags: follow directions, add water gradually
-> Consistency: should hold its shape on the trowel, not run off
-> Like thick peanut butter, not pancake batter
-> Mix small batches -- mortar sets in 90 minutes on a warm day
TECHNIQUE:
1. Start at the corners -- build corners up 3-4 courses first
2. Butter the bed: spread 3/4" to 1" of mortar on the course below
with the trowel (furrow it down the middle with the trowel tip)
3. Butter the head: spread mortar on the end of the brick you're placing
4. Press the brick into position. Check level immediately.
5. Tap with the trowel handle to adjust. Remove excess mortar.
6. Run a string line between built-up corners to keep courses straight
7. Every course should be level (check with level) and plumb
(check with level held vertically against the face)
8. Offset each course by half a brick (running bond) unless doing
a different pattern
9. Joint thickness: 3/8" for bricks, 3/8"-1/2" for blocks
TOOLING JOINTS:
-> After mortar firms up (thumbprint stays but mortar doesn't stick
to your thumb), tool the joints with a jointer
-> Concave joint (most common): press the jointer along the mortar,
compressing it into a curved shape that sheds water
-> Tool vertical joints first, then horizontal
-> Brush off excess mortar crumbs with a stiff brush
Agent action: Diagnose the crack type and provide the appropriate repair method.
CONCRETE CRACK DIAGNOSIS:
HAIRLINE CRACKS (less than 1/8" wide):
-> Cause: normal shrinkage during curing, minor settlement
-> Severity: cosmetic, not structural
-> Fix: concrete crack filler ($5 tube, caulk gun application)
or vinyl concrete patcher thinned slightly
WIDER CRACKS (1/8" to 1/2"):
-> Cause: settling, frost heave, tree roots, minor overload
-> Fix: chisel the crack wider at the bottom than the top
(creates a key that holds the patch), clean out debris,
dampen the surfaces, fill with vinyl concrete patcher
STRUCTURAL CRACKS (in foundations):
-> HORIZONTAL cracks in a foundation wall = lateral soil/water pressure
pushing the wall inward. This is SERIOUS. Call a structural engineer.
-> STAIR-STEP cracks in block foundation walls = differential settlement.
Call an engineer if they're wider than 1/4" or actively growing.
-> VERTICAL foundation cracks: most common, usually from shrinkage.
Repair with epoxy injection kit ($30-50) to seal against water.
-> If in doubt about any foundation crack, get a structural engineer
to look at it. A $200-400 inspection is cheap compared to a failed
foundation.
SPALLING (surface flaking):
-> Cause: freeze/thaw damage, deicing salts, poor original finishing
-> Fix: clean loose material, apply bonding agent, then resurface
with vinyl concrete patcher or self-leveling overlay
-> Prevention: seal concrete surfaces with concrete sealer every 2-3 years
in freeze/thaw climates
SINKING SLAB SECTIONS:
-> Cause: soil erosion under the slab, poor compaction at construction
-> DIY: mudjacking compound (foam injection kits, $50-100 for small areas)
-> Professional mudjacking: $500-1500, much cheaper than replacement
-> If the slab is badly broken AND sunken, replacement may be the
only real fix
Agent action: Cover step construction for common residential applications.
CONCRETE STEPS:
DIMENSIONS:
-> Riser height (vertical): 7" standard (building code range: 4-7.75")
-> Tread depth (horizontal): 11" minimum (deeper is more comfortable)
-> All risers must be the same height -- uneven risers cause falls
-> Width: 36" minimum for code, 48" is more comfortable
FORM BUILDING:
-> Build side forms from 3/4" plywood cut to the step profile
-> Support with 2x4 stakes driven into the ground
-> Add riser boards (2x6 or 2x8 cut to riser height) across the front
of each step
-> Brace everything heavily -- concrete is heavy (150 lbs per cubic foot)
and will blow out weak forms
-> The bottom step form sits on compacted gravel
-> Rebar: #3 rebar in a grid inside the steps, tied to pins drilled
into the existing foundation if connecting to a building
POURING AND FINISHING:
-> Start at the bottom step, fill each step fully
-> Screed each tread level with the riser boards
-> Bull float each tread surface
-> Wait for bleed water to disappear, then finish with a hand float
-> Broom finish (drag a push broom across) for non-slip surface
-> Edge all exposed edges
-> Round the nosing (front edge of each tread) with an edger
CURING:
-> Same as a slab: moist cure for 7 days
-> Keep covered with plastic and mist daily
-> No foot traffic for 48 hours, full load at 7 days
state:
project:
type: null # slab, retaining_wall, brick_wall, steps, repair, planter
dimensions: null
height: null
materials_calculated: false
permit_checked: false
site_conditions:
soil_type: null
slope: null
frost_depth: null
drainage_plan: null
near_structures: false
materials:
concrete_type: null # premixed_bags, ready_mix_truck
mortar_type: null # type_S, type_N, type_M
reinforcement: null # wire_mesh, rebar, fiber, none
quantity_needed: null
quantity_ordered: null
progress:
site_prepared: false
forms_built: false
reinforcement_placed: false
poured: false
finished: false
curing: false
cure_day: 0
forms_removed: false
repair:
crack_type: null # hairline, moderate, structural, spalling
location: null
cause_identified: null
professional_needed: false
triggers:
- name: permit_check
condition: "project.type IS SET AND project.permit_checked IS false"
action: "Before you start, check with your local building department about permit requirements. Retaining walls over a certain height, any structural work, and slabs for new structures often require permits. A quick call can save you from tearing it all down later."
- name: structural_crack_warning
condition: "repair.crack_type IS 'structural'"
action: "That sounds like a structural crack. Before attempting any repair, get a structural engineer to evaluate it. A $200-400 inspection tells you whether this is a simple fix or a sign of a bigger foundation problem. Don't seal over a crack that's telling you something important."
- name: retaining_wall_height_check
condition: "project.type IS 'retaining_wall' AND project.height > 48"
action: "A retaining wall over 4 feet needs a structural engineer to design it. The forces involved increase dramatically with height, and failure puts people and property at risk. This isn't a cost-saving situation -- it's a safety situation."
- name: curing_reminder
condition: "progress.curing IS true AND progress.cure_day < 7"
schedule: "daily for 7 days"
action: "Day {cure_day} of concrete curing. Mist the surface with water and make sure the plastic cover is in place. Concrete gains most of its strength in the first 7 days, but only if it stays moist. Don't let it dry out."
- name: weather_check
condition: "progress.poured IS false AND project.type IN ['slab', 'steps', 'retaining_wall']"
action: "Check the weather forecast before you pour. You need at least 48 hours above 40F/4C after pouring, and rain on fresh concrete damages the surface. The ideal window is mild, overcast days in the 50-70F range."