composite-curing

name	composite-curing
description	Master skill for composite curing simulation with mold contact, friction, temperature, and Model Change springback in Abaqus. Routes to appropriate specialized skills.

Composite Curing Simulation (Master Router)

This is the master routing skill for composite curing simulation. It does not perform work directly. Instead, it classifies the user's request and routes to the appropriate specialized sub-skill within the composite-curing-simulation collection.

When to Invoke

Invoke this skill when the user's request falls into any of the following categories:

• Curing simulation: User asks to run or set up a composite curing simulation in Abaqus
• Springback analysis: User mentions springback, mold removal, demolding, or *Model Change
• Mold contact: User needs mold/tool contact geometry, contact pairs, or friction setup
• Composite layup with mold: User wants to define or modify a composite layup that interacts with a mold during curing
• UMAT for composites: User needs to run Abaqus with a UMAT subroutine for composite materials (e.g., Threestep.for)
• Temperature-dependent friction: User mentions changing friction coefficients across curing steps
• Ply angle or ply count changes: User wants to modify ply angles, ply count, or layup sequence in an existing curing model

If the request is a single, well-scoped sub-task (e.g., only changing a ply angle), you may route directly to the relevant sub-skill without invoking this router first. Use this router when the request spans multiple stages or when the user is unsure which sub-skill applies.

Architecture Overview

The curing model consists of two parts in the Abaqus assembly:

1. P8 (Composite Part): An L-shaped bracket with through-thickness solid elements (C3D8). The composite layup is defined via *Solid Section, composite with a stack direction of 3. The through-thickness direction is along the X-axis (from -1 to 0).

2. Tool (Mold Part): A separate rigid-like mold part that contacts the composite outer surface during curing. The mold is removed in the springback step via *Model Change.

Through-Thickness Direction

The composite thickness lies along the X-axis. For a 4-ply layup, the thickness spans from X = -1 to X = 0 (1 mm total, 0.25 mm per ply). For an 8-ply layup, the same total thickness of 1 mm is divided into 8 plies of 0.125 mm each. The stack direction in *Solid Section is 3 (the third local axis defined by the orientation).

4-Step Curing Process

Step	Name	Temperature	Pressure	Friction (mu)	Purpose
1	vis	25C to 150C	0.6 MPa	0.45	Viscous heating phase
2	rub	150C to 180C	0.6 MPa	0.2	Rubbery curing phase
3	glassy	180C to 25C	(removed)	0.169	Glassy cooling phase
4	sp	25C (held)	(removed)	(inactive)	Springback after mold removal

Routing Table

Use the table below to determine which sub-skill to invoke. When multiple sub-skills are relevant, invoke them in the order listed under "Recommended Chain Order".

User Intent / Keywords	Sub-Skill	Category
Ply angles, ply count, thickness, layup sequence	modeling/composite-layup	modeling
Tool part, mold surfaces, mold geometry, tool material	modeling/mold-geometry	modeling
C3D8 elements, through-thickness mesh, composite mesh	modeling/composite-mesh	modeling
UMAT, COM material, TOOL material, Depvar, Expansion	setup/curing-material	setup
Contact pair, friction properties, Change Friction	setup/curing-contact	setup
Tool BCs, Set-2 springback constraint, boundary	setup/curing-bc	setup
Pressure on inner surface S2, Dsload	setup/curing-load	setup
Temperature fields, initial conditions, predefined	setup/curing-temperature	setup
4-step process, vis/rub/glassy/sp, Static step setup	analysis/curing-steps	analysis
Model Change, mold removal, springback step	analysis/springback-analysis	analysis
Job submission with UMAT, JobFromInputFile	execution/curing-job	execution
Socket bridge usage, TCP port 48152, Abaqus kernel	execution/socket-bridge	execution
ODB field output, stress/strain/displacement extraction	postprocessing/odb-extraction	postprocessing
CSV export with coordinates + displacement	postprocessing/csv-export	postprocessing

Recommended Chain Order

For a complete curing simulation from scratch, follow this chain order. Each stage depends on the output of the previous stage:

1. modeling/composite-layup        # Define ply angles, thickness, count
2. modeling/mold-geometry          # Create tool/mold part and surfaces
3. modeling/composite-mesh         # Generate through-thickness C3D8 mesh
4. setup/curing-material           # Define COM (UMAT) and TOOL materials
5. setup/curing-contact            # Set up contact pair and friction properties
6. setup/curing-bc                 # Apply tool BCs and Set-2 springback constraint
7. setup/curing-load               # Apply pressure on inner surface S2
8. setup/curing-temperature        # Define temperature fields and initial conditions
9. analysis/curing-steps           # Configure 4-step process (vis/rub/glassy/sp)
10. analysis/springback-analysis   # Configure Model Change and mold removal
11. execution/curing-job           # Submit job with UMAT subroutine
12. execution/socket-bridge        # Connect to Abaqus kernel via socket bridge
13. postprocessing/odb-extraction  # Extract ODB field outputs
14. postprocessing/csv-export      # Export CSV with coordinates + displacement

Stage Dependencies

• Modeling (steps 1-3) must be completed before Setup (steps 4-8), because material assignments, contact surfaces, and boundary sets reference the mesh.
• Setup (steps 4-8) must be completed before Analysis (steps 9-10), because steps reference loads, BCs, and contact pairs defined in setup.
• Analysis (steps 9-10) must be completed before Execution (steps 11-12), because the job is submitted from the complete INP.
• Postprocessing (steps 13-14) runs after the job completes successfully.

Common Routing Scenarios

Scenario 1: Change Ply Angles Only

User says: "Change the layup to [45/-45]*4."

Route to: modeling/composite-layup only. This is a text-level INP edit that does not require mesh regeneration.

Scenario 2: Change Ply Count

User says: "Switch from 4 plies to 8 plies."

Route to: modeling/composite-layup (for layup definition) then modeling/composite-mesh (for mesh regeneration). Changing ply count requires regenerating the through-thickness mesh, not just editing ply lines.

Scenario 3: Run Full Curing Simulation

User says: "Run a curing simulation with the default layup."

Route through the full chain: modeling/* then setup/* then analysis/* then execution/* then postprocessing/*.

Scenario 4: Extract Results

User says: "Get the displacement results from the completed job."

Route to: postprocessing/odb-extraction then postprocessing/csv-export.

Key References

• UMAT subroutine: Fortran file (e.g., Threestep.for) with 4 state variables
• Reference INP: Contains mold geometry, contact, loads, steps (e.g., Job-0_0_0_0.inp)
• Pre-built composite model: For ply count changes (e.g., P8_only_recipe_1.inp for 8 plies)
• Socket bridge: TCP on 127.0.0.1:48152 inside Abaqus CAE

Common Pitfalls

1. Ply count vs ply angles: Changing ply angles is a text edit; changing ply count requires mesh regeneration. Do not confuse the two.
2. Pressure surface: Pressure is applied on S2 (inner surface), NOT S1 (outer/contact surface). Routing to setup/curing-load must preserve this distinction.
3. Tool node numbering: Tool and composite parts both start from node 1. Parse nodes per-part, not globally.
4. Set-2 node matching: When merging models with different through-thickness meshes, match nodes by exact coordinate lookup, not by node ID.
5. Unicode errors: Use consistencyChecking=OFF in submit() when running via the socket bridge.