design-controlled-experiment

name	design-controlled-experiment
description	Use when planning a physics experiment that requires controlling variables to isolate causal relationships between physical quantities
source	Fisher "The Design of Experiments" (1935); Box, Hunter & Hunter "Statistics for Experimenters" (2005); NIST/SEMATECH e-Handbook of Statistical Methods
tags	["physics","experiment-design","controls","scientific-method"]
verified	true

Design Controlled Experiment

Plan a physics experiment that isolates a single causal variable while controlling all others, enabling valid causal inference.

Why This Is Best Practice

Adopted by: NIST measurement science protocols, CERN experimental design review process, APS (American Physical Society) experimental reporting standards, NSF research grant requirements.

Impact: Factorial design (Box & Hunter) reduces the number of required experimental runs by 50–90% compared to one-factor-at-a-time approaches while simultaneously revealing interactions; NIST calibration studies using designed experiments achieve measurement uncertainty reductions of 30–60%.

Why best: Proper control structure is the only mechanism by which an experiment can support causal claims rather than correlational observations; without it, confounders are indistinguishable from true effects.

Sources: Fisher "Design of Experiments" (1935); Box, Hunter & Hunter 2nd ed. (2005) ch. 3–5; NIST/SEMATECH e-Handbook §5.

Steps

1. Define the causal question — state explicitly: "Does [independent variable X] cause a change in [dependent variable Y], holding [list of control variables Z₁, Z₂, ...] constant?"

2. Map all variables — categorize every variable as: independent (manipulated), dependent (measured), controlled (held constant), or nuisance (known to vary but not of interest → randomize or block).

3. Choose the experimental design — select from: completely randomized design (CRD, for homogeneous material), randomized block design (RBD, for known nuisance variables), factorial design (multiple independent variables and their interactions), or response surface design (optimization).

4. Define measurement protocol — specify: instrument, calibration procedure, range, resolution, sampling rate, and number of repeated measurements per condition. Reference calculate-measurement-uncertainty.

5. Randomize run order — use a random number generator to determine the order of experimental runs; this distributes unknown time-dependent effects (instrument drift, temperature fluctuations) across all conditions.

6. Implement blocking — if a nuisance variable cannot be controlled (e.g., different batches of material, different days), group runs into blocks where the nuisance is constant and include block as a factor in analysis.

7. Replicate — perform ≥3 independent replications (not repeated measurements of the same run) to estimate run-to-run variability and support statistical inference.

8. Record all conditions — log every environmental parameter (temperature, pressure, humidity, operator, instrument serial number) at the time of each run, even those believed to be controlled.

9. Analyze with ANOVA or regression — test the effect of the independent variable while accounting for block effects; report effect size (η² or ω²), F-statistic, and p-value; plot residuals to verify model assumptions.

10. Interpret within scope — conclusions apply only to the range of conditions tested (no extrapolation beyond the experimental domain without physical model justification).

Rules

• Control variables must be actively monitored and documented — assuming they are constant without measurement introduces undetectable confounders.
• Never change more than one variable between conditions in a controlled experiment — the entire purpose is isolation.
• Randomization is mandatory; alternating treatment-control-treatment is not randomization.
• Report all failed or excluded runs with reason for exclusion — selective omission is data fabrication.

Common Mistakes

• Confounding with time — running all treatment conditions first, then all controls, means any time-dependent drift (instrument warm-up, sample aging) is confounded with the treatment effect.
• Technical replicates only — measuring the same sample three times is not replication; it estimates measurement noise, not run-to-run experimental variability.
• No baseline or reference condition — without a reference point (zero-field, room temperature, no treatment), the magnitude of the effect cannot be quantified.
• Insufficient range of independent variable — testing X over too narrow a range may miss the functional relationship or underestimate the effect.

When NOT to Use

• For observational studies where manipulation is impossible (use matched cohort or natural experiment methods)
• For theoretical/computational studies (use sensitivity analysis and verification/validation methodology instead)
• For engineering design optimization over a large parameter space (use Design of Experiments software: JMP, Minitab, or Python pyDOE)