| name | ee |
| description | Electrical and electronic engineering reference — circuit analysis, component selection, power supply design, signal integrity, RF, thermal, EMC, and test & measurement. Use for design questions, calculations, component vetting, and first-principles analysis. Do not orchestrate a complete new board from requirements; use circuit-weaver for that end-to-end workflow.
|
Core Circuit Laws
DC Analysis
V = IR Ohm's Law
P = VI = I²R = V²/R Power
KVL: ΣV around loop = 0 Kirchhoff's Voltage Law
KCL: ΣI into node = 0 Kirchhoff's Current Law
Voltage Divider
Vout = Vin × R2 / (R1 + R2)
Rload effect: Vout_actual = Vin × (R2||Rload) / (R1 + R2||Rload)
For < 1% load error: Rload > 100 × R2
Thevenin / Norton
Vth = open-circuit voltage at terminals
Rth = resistance seen from terminals with all sources zeroed (V→short, I→open)
In = Vth / Rth
Superposition
For linear circuits: activate one source at a time, zero others, sum results.
Passive Components
Resistors
| Parameter | Calculation | Notes |
|---|
| Power derate | P_rated × 0.5 at 70°C | Derate linearly to 0 at T_max |
| Noise (Johnson) | Vn = √(4kTRB) | k=1.38e-23, B=bandwidth |
| Tolerance effect | ΔVout/Vout = √(ΔR1²+ΔR2²) / (R1+R2) | Worst-case RSS |
Standard E-series values: E12 (10% tol), E24 (5%), E48 (2%), E96 (1%), E192 (0.5%)
SMD sizes: 0201, 0402 (¼W), 0603 (⅒W), 0805 (⅛W), 1206 (¼W), 2512 (1W)
Capacitors
| Type | Voltage coeff | Temp coeff | Use case |
|---|
| C0G/NP0 | None | ±30 ppm/°C | Timing, RF, precision |
| X7R | Moderate (−80% at rated V) | ±15% (-55→125°C) | Decoupling |
| X5R | Higher | ±15% (-55→85°C) | Bulk, lower-cost decoupling |
| Y5V | Severe (−82% at rated V) | +22/−82% | Avoid for power |
| Electrolytic | Low | Varies | Bulk, low-freq only |
| Tantalum | Low | Stable | Bulk; high inrush risk |
Derating rule: Use caps at ≤ 50% rated voltage for X7R (capacitance drops ~20% at 50%). Check datasheet derating curves.
Self-resonant frequency (SRF): Above SRF, cap is inductive. Rule of thumb: 0402 MLCC SRF ≈ 200–600 MHz, 0201 ≈ 1–3 GHz.
Decoupling placement: Place closest cap to IC power pin first. Cascade: bulk (10–100 µF) + mid (1–10 µF) + HF (100 nF) + ultra-HF (10 nF). Minimize loop area.
Inductors
V = L × dI/dt
Isat: current at which inductance drops 20–30%
Irms: continuous current at rated temperature rise
Q = ωL / R_dc Quality factor
SRF: above this, acts capacitive
DCR power loss: P = I² × DCR. Key spec for power inductors.
Saturation: Never exceed Isat. Size to Ipeak × 1.3 minimum margin.
RC / LC Circuits
RC Low-Pass Filter
fc = 1 / (2π × R × C) Cutoff frequency (-3 dB)
Attenuation at f: A = 1 / √(1 + (f/fc)²)
Phase shift: φ = -arctan(f/fc)
RC High-Pass Filter
fc = 1 / (2π × R × C)
A = (f/fc) / √(1 + (f/fc)²)
LC Resonant Circuit
f0 = 1 / (2π × √(L × C)) Resonant frequency
Q = (1/R) × √(L/C) Series resonance
BW = f0 / Q Bandwidth at -3 dB
Z = √(L/C) Characteristic impedance
π / T filter (EMC)
π: cap–inductor–cap (low impedance source/load)
T: inductor–cap–inductor (high impedance source/load)
Op-Amps
Ideal Op-Amp Rules
- V+ = V− (virtual short)
- Input current = 0
Common Configurations
| Config | Gain | Formula |
|---|
| Inverting | −Rf/Rin | Vout = -(Rf/Rin) × Vin |
| Non-inverting | 1 + Rf/Rin | Vout = (1 + Rf/Rin) × Vin |
| Voltage follower | 1 | Vout = Vin |
| Differential | Rf/Rin | Vout = (Rf/Rin)(V+ − V−) |
| Integrator | −1/(RC×s) | Vout = −(1/RC)∫Vin dt |
| Differentiator | −RC×s | Vout = −RC × dVin/dt |
Key Specs
- GBW (gain-bandwidth product): Gain × BW = constant. Av=10 → BW = GBW/10.
- Slew rate: Maximum dVout/dt. Limits large-signal bandwidth: fmax = SR / (2π × Vpeak).
- Input offset voltage (Vos): DC error. Total output offset = Vos × (1 + Rf/Rin).
- CMRR: Common-mode rejection. Target > 80 dB for precision.
- PSRR: Power supply rejection. Decouple op-amp supplies with 100 nF close.
Power Supply Design
LDO Linear Regulator
Vout = Vref × (1 + R1/R2) Adjustable output
Pdiss = (Vin - Vout) × Iout Power dissipation (heat!)
η = Vout / Vin Efficiency (poor for large dropout)
When to use LDO: Low noise, small dropout (< 0.5V), < 500 mA, noise-sensitive analog/RF.
Min dropout voltage: Vin ≥ Vout + Vdropout (typically 100–300 mV for modern LDOs).
Thermal check: θJA × Pdiss < Tj_max − Tambient. Use exposed pad or heatsink if > 1W.
Buck Converter (Step-Down)
D = Vout / Vin Duty cycle (ideal, continuous mode)
ΔIL = (Vin - Vout) × D / (L × fsw) Inductor ripple current
ΔVout = ΔIL / (8 × C × fsw) Output voltage ripple
Lmin = (Vin - Vout) × D / (2 × Iout × fsw) Min L for CCM
Component selection:
- L: Isat > Iout + ΔIL/2. L value for 20–40% ripple ratio.
- Cin: rated for Vin, low ESR. Irms_cin = Iout × √(D(1-D)).
- Cout: C > ΔIL / (8 × fsw × ΔVout_spec). ESR < ΔVout / ΔIL.
Layout rules: Short, fat traces on switching node. Input cap right at Vin pin. GND plane under switcher. Keep Lx node away from feedback resistors.
Boost Converter (Step-Up)
D = 1 - Vin/Vout Duty cycle
ΔIL = Vin × D / (L × fsw) Inductor ripple
Isat_req = Iout/(1-D) + ΔIL/2 Peak inductor current
Power Budget Template
| Rail | Voltage | Current | Power |
|---|
| +3.3V_IO | 3.3V | xxx mA | xxx mW |
| +1.8V_DDR | 1.8V | xxx mA | xxx mW |
| +1.0V_CORE | 1.0V | xxx mA | xxx mW |
| Total | | | xxx mW |
Add 20% margin for thermal and headroom.
Transistors
BJT
IC = β × IB Collector current
VCE_sat ≈ 0.2V (ON), VBE ≈ 0.7V
IB_req = IC / (β × 0.1) Force saturation: overdrive 10×
Pdiss = VCE × IC (linear) or VCEsat × IC (switch)
Check: IC < IC_max, VCE < VCEO, Pdiss < Pd_max.
MOSFET
ID = (k/2)(VGS - Vth)² Saturation
VGS > Vth + safety margin Fully enhanced
Rds(on) varies with VGS and Tj: derate 2× from datasheet at 125°C vs 25°C
Pdiss (switch) ≈ ID² × Rds(on) + Qg × VGS × fsw
Gate drive: Sufficient VGS for low Rds(on). Drive impedance limits switching speed → EMI trade-off.
Body diode: Always present; check reverse recovery for high-side switches.
Signal Integrity
Transmission Lines
Z0 = √(L/C) Characteristic impedance
v = 1/√(LC) = c/√(εr_eff) Propagation velocity
λ = v/f Wavelength
Rule of thumb: Treat trace as transmission line when length > λ/10 at the signal's knee frequency (≈ 0.35/tr for digital).
Microstrip (PCB, trace over ground plane):
Z0 ≈ (87/√(εr+1.41)) × ln(5.98H / (0.8W + T))
εr_eff ≈ (εr+1)/2 + (εr-1)/2 × (1+12H/W)^(-0.5)
- H = height to ground plane, W = trace width, T = trace thickness
- FR4: εr ≈ 4.0–4.5 (use 4.2 at 1 GHz), εr_eff ≈ 3.0
Stripline (buried trace between planes): Fully enclosed, εr_eff = εr, no dispersion. Use for tight impedance control.
Termination:
- Series: R = Z0, at source. Eliminates reflections at load (point-to-point).
- Parallel: R = Z0 to GND, at load. Eliminates reflections at source (multi-drop).
- AC: cap in series with R. DC-blocking parallel termination.
Return Paths
Signal current returns via lowest impedance path — not the shortest ground path. At high frequency, this is directly beneath the signal trace (the image current in the reference plane).
Rules:
- Never split ground plane under a high-speed signal. Splits force current around the gap → loop antenna.
- Cross splits only through bypass caps bridging the split.
- Via stitching closes return path at layer transitions.
Crosstalk
NEXT (near-end) ≈ (Cm/C0 + Lm/L0) / 4
FEXT (far-end) ≈ (Cm/C0 - Lm/L0) / 4 × TD
Reduce crosstalk: Increase trace spacing (3W rule: spacing ≥ 3× trace width), reduce parallel run length, use ground guard traces, use differential pairs.
RF Design
dB Reference Table
| Power ratio | dB |
|---|
| 2× | +3 dB |
| 10× | +10 dB |
| 0.5× | −3 dB |
| 0.1× | −10 dB |
dBm: Power relative to 1 mW. 0 dBm = 1 mW, +30 dBm = 1 W.
dBW: Relative to 1 W. 0 dBW = +30 dBm.
RF Chain Budget
Pout = Pin + Gain − Losses
NF_total = NF1 + (NF2-1)/G1 + (NF3-1)/(G1×G2) + ... (Friis formula)
IP3_total: 1/IP3_in = 1/IP3_1 + G1/IP3_2 + G1G2/IP3_3 ...
Sensitivity: Sens = kTB + NF + SNRmin = −174 + 10log(BW) + NF + SNRmin [dBm]
S-Parameters
| Parameter | Meaning |
|---|
| S11 | Input reflection (return loss). Good: < −10 dB |
| S21 | Forward gain (or insertion loss if passive) |
| S22 | Output reflection |
| S12 | Reverse isolation |
Return loss: RL = −20 log|Γ|. VSWR = (1+|Γ|)/(1−|Γ|).
Insertion loss: IL = −20 log|S21| for a 2-port.
Impedance Matching (L-network)
Given Rsource → Rload (both real, Rsource > Rload):
Q = √(Rsource/Rload - 1)
Xs (series element) = Q × Rload
Xp (shunt element) = Rsource / Q
BW ≈ f0/Q. Use π or T networks for narrower BW.
Thermal Design
Heat Flow
Tj = Ta + Pdiss × (θJC + θCS + θSA)
θJA = θJC + θCS + θSA Junction-to-ambient total
- θJC: Junction-to-case (datasheet)
- θCS: Case-to-sink (thermal interface material — TIM)
- θSA: Sink-to-ambient (heatsink spec, depends on airflow)
- Ta: Ambient temperature
Copper area as heatsink: 1 in² of 1 oz copper ≈ 50–70°C/W (still air). Doubles with 2 oz copper.
Thermal via: Each via ≈ 3–10°C/W. Use arrays under exposed pads (QFN, BGA). Guideline: 1 via per 100 mW for QFN.
Derate components: At T > 25°C, many parameters degrade. Check derating curves: Rds(on) of MOSFETs typically doubles 25→125°C.
Junction Temp Check
Tj_max (datasheet) — Tj_operating ≥ 10°C margin
Tj = Ta + Pdiss × θJA
If Tj > limit: reduce Pdiss, increase copper area, add heatsink, improve airflow, choose lower Rds(on) part.
EMC
Emission Reduction
Common-mode filter: Series CM choke + shunt caps (π filter) on cable exits.
Differential-mode filter: LC filter on power lines.
Shielding: Enclosure or shielded connector. Ground the shield at one point (low-freq) or both (high-freq > 1 MHz).
Layout Rules for EMC
- Minimize loop areas — current loops are antennas. Keep signal and return traces close.
- Solid ground plane — no splits under switching circuits or clock lines.
- Separate grounds — AGND and DGND joined at single star point (or solid plane with careful routing).
- Decoupling every IC — 100 nF + bulk cap, right at VCC pins, shortest possible trace.
- Clock/oscillator — keep under metal (internal layer or add copper pour), surround with GND vias.
- High-current loops first — SMPS switching loop, gate drive loop. Minimize physically.
Common Failure Modes
| Symptom | Likely cause |
|---|
| Oscillation in amplifier | Parasitic feedback, missing decoupling |
| SMPS noise on analog rail | Insufficient filtering, layout ground loop |
| Erratic digital behavior | Ground bounce, inadequate bulk caps |
| ESD latchup | Missing ESD diodes on I/O, wrong ground return |
| EMC emission at clock frequency | Clock harmonics, inadequate shielding |
Protection Circuits
ESD Protection
- TVS diode: Clamp voltage, bidirectional or unidirectional. Select Vclamp < IC's abs max.
- Rail-to-rail TVS: One device per supply rail.
- Line protection: Series R (33–100 Ω) + TVS to GND. Limits ESD current into IC.
Overcurrent Protection
Ifuse = Imax_load × 1.5 Fuse rating (with 50% margin)
Rsense = Vsense / Ilimit Current sense resistor (Vsense typically 50–100 mV)
Polyfuse (PPTC): Self-resetting. Trips when Joule heating exceeds threshold. Slow — not for fast faults.
Ideal diode / load switch: MOSFET-based, fast, no voltage drop.
Reverse Polarity
- Series diode (Schottky): Simple, 0.3–0.5V drop.
- P-channel MOSFET: Near-zero drop, controlled by gate. Source to input+, drain to load+, gate through R to GND, TVS gate-source.
Overvoltage
- Clamp: TVS or Zener in parallel with load.
- Crowbar (SCR): Fires on OV event, blows fuse. Latching — requires power cycle.
- Ideal OVP: Comparator + MOSFET series switch. Non-latching.
Test & Measurement
Oscilloscope Setup
| Setting | Rule of Thumb |
|---|
| Bandwidth | ≥ 5× signal bandwidth (≥ 3.5× for digital: 0.35/tr) |
| Sample rate | ≥ 5× signal bandwidth |
| Probe compensation | Square-wave comp at 1 kHz before measuring |
| Ground clip | Shortest possible — loop is antenna |
| Probe loading | 10 MΩ ‖ 10 pF at 1× → use 10× probe (10 MΩ ‖ 1 pF) for fast signals |
Measure power supply noise: AC-couple, 20 MHz BW limit, 100 mV/div. Short probe ground.
DMM Tips
- Resistance: Power off, discharge caps, avoid measuring in-circuit (parallel paths).
- Diode test: 0.3–0.5V = Schottky/Ge, 0.6–0.7V = Si, OL = open, ~0 = short/zener-in-circuit.
- Continuity: Not reliable for detecting shared return paths (other paths sink current).
Spectrum Analyzer / Tinker SA
- Resolution bandwidth (RBW): narrower → slower sweep, better sensitivity.
- Reference level: Set 10 dB above expected signal.
- Span: Start wide, then zoom in.
- Input protection: Know your max input power. +10 dBm (10 mW) is common; check before connecting.
Calibration / Null Measurements
- Use 4-wire (Kelvin) sensing for resistance < 10 Ω to eliminate lead resistance.
- Thermal EMF (Seebeck effect) corrupts µV-level DC measurements. Use DC reversal method.
- Lock-in amplifier: Detect signals buried in noise; phase-lock to known reference.
Component Selection Checklist
For every component in a new design:
Quick Reference — Standard Values
Resistor Values (E24 common subset)
1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.8, 2.0, 2.2, 2.4, 2.7, 3.0, 3.3, 3.6, 3.9, 4.3, 4.7, 5.1, 5.6, 6.2, 6.8, 7.5, 8.2, 9.1 (× 10^n)
Capacitor Common Values
1, 1.5, 2.2, 3.3, 4.7, 10, 22, 47, 100 nF; 1, 2.2, 4.7, 10, 22, 47, 100 µF
Typical I²C Pull-Up Values
- 3.3V, 400 kHz (fast-mode): 2.2 kΩ – 4.7 kΩ
- 3.3V, 100 kHz (standard): 4.7 kΩ – 10 kΩ
- 1.8V, 400 kHz: 1 kΩ – 2.2 kΩ
Crystal Load Capacitors
CL_ext = 2 × CL_spec − Cstray (Cstray ≈ 3–5 pF)
Typical: 12 pF spec → 18–22 pF external caps
USB Signal Integrity
- USB 2.0 FS/HS differential impedance: 90 Ω ± 15%
- USB 3.x differential impedance: 85 Ω ± 15%
- USB 3.x max length: 1m (channel loss < 8 dB at Nyquist)
Integration with KiCad Skills
This skill feeds the rest of the EDA workflow:
| Calculation | → Use in |
|---|
| Voltage divider for VREF | circuit-weaver validate design.yaml --enhanced: verify feedback resistors |
| LDO dropout check | circuit-weaver validate design.yaml --enhanced: verify rail headroom |
| Inductor current ripple | bom: confirm Isat rating from DigiKey |
| Crystal load caps | circuit-weaver validate design.yaml --enhanced: verify Cload in schematic |
| I²C pull-up values | analyze_schematic.py bus detection output |
| Signal trace impedance | analyze_pcb.py trace width + stackup |
| Thermal check | circuit-weaver validate design.yaml --enhanced: flag missing thermal evidence |
| EMC filter values | circuit-weaver simulate design.yaml where supported; external RF analysis otherwise |
Platform Guidance
- Claude Code: Present calculation results inline with units. Use AskUserQuestion when multiple approaches exist.
- Codex/OpenCode: Present formulas and results as text. Ask user for missing parameters.
- CLI: Reference calculations available via the
ee skill. No dedicated CLI subcommand.
