Menu
Use when developing with Raspberry Pi Pico 2 or the Pi Debug Probe.
The review-first prompt is selected by default. You can switch to a direct command or download a local copy.
Read SKILL.md and any companion files shown by SkillsMP before deciding whether to install.
Install with Codex or Claude Copy this prompt, paste it into Codex, Claude, or another assistant, and let it review the skill page and install it for you.
A direct command skips the review prompt. Inspect the source before running it.
npx skills add https://github.com/sammcj/agentic-coding --skill raspberry-pi-pico2The command stays on one line. Scroll horizontally to inspect it before copying.
Prefer a local copy? Download the files currently available to SkillsMP.
Showing SKILL.md
| name | raspberry-pi-pico2 |
| description | Use when developing with Raspberry Pi Pico 2 or the Pi Debug Probe. |
| allowed-tools | Bash Read Write Edit Grep Glob Agent |
This skill covers development with Raspberry Pi Pico 2 (RP2350) boards and the Raspberry Pi Debug Probe. It includes hardware specs, SDK setup, build configuration, debugging workflows, and common pitfalls.
Consult these for detailed technical content. Read only the file relevant to the current task:
references/pico2-hardware.md - RP2350 specs, RP2040 vs RP2350 comparison, pin layout, wireless variant, security features, chip variantsreferences/debug-probe.md - Debug Probe hardware, wiring diagrams, OpenOCD setup, GDB workflow, UART serial, RTT, VS Code integration, rescue mode, troubleshootingreferences/sdk-toolchain.md - pico-sdk setup, CMake configuration, ARM vs RISC-V builds, picotool commands, MicroPython/CircuitPython, project structure| Board | CMake Flag | Platform |
|---|---|---|
| Pico 1 | -DPICO_BOARD=pico (default) | rp2040 |
| Pico 1 W | -DPICO_BOARD=pico_w | rp2040 |
| Pico 2 | -DPICO_BOARD=pico2 | rp2350-arm-s |
| Pico 2 W | -DPICO_BOARD=pico2_w | rp2350-arm-s |
| Pico 2 RISC-V | -DPICO_BOARD=pico2 -DPICO_PLATFORM=rp2350-riscv | rp2350-riscv |
| Debug Probe "D" Pin | Wire Colour | Pico 2 SWD Pad |
|---|---|---|
| SC | Orange | SWCLK |
| GND | Black | GND |
| SD | Yellow | SWDIO |
| Debug Probe "U" Pin | Wire Colour | Pico 2 Pin | GPIO |
|---|---|---|---|
| TX | Orange | Pin 2 | GP1 (RX) |
| RX | Yellow | Pin 1 | GP0 (TX) |
| GND | Black | Pin 3 | GND |
Note the crossover: probe TX to Pico RX, probe RX to Pico TX.
| Target | Config File |
|---|---|
| Pico 1 (RP2040) | target/rp2040.cfg |
| Pico 2 (RP2350) | target/rp2350.cfg |
| Pico 2 RISC-V | target/rp2350.cfg with -c "set USE_CORE { rv0 rv1 }" |
| Rescue (RP2350) | target/rp2350.cfg with -c "set RESCUE 1" |
# Terminal 1: OpenOCD
openocd -f interface/cmsis-dap.cfg -f target/rp2350.cfg -c "adapter speed 5000"
# Terminal 2: GDB
arm-none-eabi-gdb my_app.elf
(gdb) target remote localhost:3333
(gdb) monitor reset init
(gdb) load
(gdb) break main
(gdb) continue
openocd -f interface/cmsis-dap.cfg -f target/rp2350.cfg \
-c "adapter speed 5000" \
-c "program my_app.elf verify reset exit"
Use the .elf file for SWD flashing, not .uf2.
These are the most common mistakes and non-obvious behaviours. Pay close attention.
SDK defaults to Pico 1. You must explicitly pass -DPICO_BOARD=pico2 to target RP2350. Forgetting this builds for RP2040 and the binary will not run on a Pico 2.
Use the Raspberry Pi fork of OpenOCD. Upstream OpenOCD (0.12.0) lacks full RP2350 support. Clone from https://github.com/raspberrypi/openocd.git branch rpi-common.
Wrong target config = failed connection. Using rp2040.cfg with a Pico 2 silently fails. Always match the target config to the chip.
SWD uses .elf, BOOTSEL uses .uf2. These are different formats for different flashing methods. Do not try to flash a .uf2 via OpenOCD/SWD.
Debug builds required for meaningful debugging. Always pass -DCMAKE_BUILD_TYPE=Debug to cmake. Release builds optimise away variable state and reorder code, making breakpoints unreliable.
RISC-V mode has no FPU. The hardware floating-point unit is only available on Cortex-M33. RISC-V mode uses software float, which is significantly slower for float-heavy code.
RISC-V requires a clean build directory. When switching between ARM and RISC-V, delete the build directory and re-run cmake. In-place switching does not work.
RISC-V debugging requires pre-selection. The RP2350 boots into Cortex-M33 by default. To debug RISC-V: picotool reboot -u -c riscv, then use OpenOCD with set USE_CORE { rv0 rv1 }.
Debug Probe does not power the target. The Pico 2 must be powered via its own USB or VSYS. The SWD connector carries no power.
LED pin differs on wireless models. Non-wireless Pico 2 uses GP25 for the onboard LED. Pico 2 W uses WL_GPIO0 through the CYW43439 wireless chip. Code must be conditional.
Git submodules are required. The pico-sdk needs git submodule update --init to pull tinyusb, cyw43-driver, lwip, btstack, and mbedtls. Missing submodules cause cryptic build failures.
OTP is irreversible. Writing OTP bits is permanent. Misconfiguring secure boot (setting SECURE_BOOT_ENABLE without a boot key and with PICOBOOT disabled) permanently bricks the device.
Wireless SPI pin sharing. On Pico 2 W, the VSYS ADC reading and CYW43439 IRQ checking are blocked during SPI transactions to the wireless chip.
Connect GND first. When the Pico 2 is powered from a separate source, connect GND between the target and Debug Probe before any signal lines. Voltage differences can damage the probe.
macOS: OpenOCD needs hidapi and libusb. Install via brew install hidapi libusb. If OpenOCD cannot find the probe, check no other process (VS Code, another OpenOCD instance) holds the USB device.
Multiple debug probes. If multiple CMSIS-DAP devices are connected, specify the serial number: adapter serial <serial_number> in your OpenOCD config.
Based on SOC occupation classification
