raspberry-pi-pico2

Use when developing with Raspberry Pi Pico 2 or the Pi Debug Probe.

インストールへ移動

リポジトリ: sammcj/agentic-coding
ソースの最終更新活動: 2026年3月24日 20:15
検出された SKILL.md の言語: 英語
スター: 156
フォーク: 25

インストール方法

デフォルトでは、最初にソースを確認する Prompt が選択されています。直接コマンドに切り替えるか、ローカルコピーをダウンロードすることもできます。

ソースファイルを確認

インストールを決める前に、SKILL.md と SkillsMP に表示されている付属ファイルをお読みください。

検索に戻るインストールに戻る

name	raspberry-pi-pico2
description	Use when developing with Raspberry Pi Pico 2 or the Pi Debug Probe.
allowed-tools	Bash Read Write Edit Grep Glob Agent

Raspberry Pi Pico 2 and Debug Probe

This skill covers development with Raspberry Pi Pico 2 (RP2350) boards and the Raspberry Pi Debug Probe. It includes hardware specs, SDK setup, build configuration, debugging workflows, and common pitfalls.

Reference Files

Consult these for detailed technical content. Read only the file relevant to the current task:

references/pico2-hardware.md - RP2350 specs, RP2040 vs RP2350 comparison, pin layout, wireless variant, security features, chip variants
references/debug-probe.md - Debug Probe hardware, wiring diagrams, OpenOCD setup, GDB workflow, UART serial, RTT, VS Code integration, rescue mode, troubleshooting
references/sdk-toolchain.md - pico-sdk setup, CMake configuration, ARM vs RISC-V builds, picotool commands, MicroPython/CircuitPython, project structure

Quick Reference

Board Selection (CMake)

Board	CMake Flag	Platform
Pico 1	`-DPICO_BOARD=pico` (default)	rp2040
Pico 1 W	`-DPICO_BOARD=pico_w`	rp2040
Pico 2	`-DPICO_BOARD=pico2`	rp2350-arm-s
Pico 2 W	`-DPICO_BOARD=pico2_w`	rp2350-arm-s
Pico 2 RISC-V	`-DPICO_BOARD=pico2 -DPICO_PLATFORM=rp2350-riscv`	rp2350-riscv

Debug Probe Wiring (SWD)

Debug Probe "D" Pin	Wire Colour	Pico 2 SWD Pad
SC	Orange	SWCLK
GND	Black	GND
SD	Yellow	SWDIO

Debug Probe Wiring (UART)

Debug Probe "U" Pin	Wire Colour	Pico 2 Pin	GPIO
TX	Orange	Pin 2	GP1 (RX)
RX	Yellow	Pin 1	GP0 (TX)
GND	Black	Pin 3	GND

Note the crossover: probe TX to Pico RX, probe RX to Pico TX.

OpenOCD Target Configs

Target	Config File
Pico 1 (RP2040)	`target/rp2040.cfg`
Pico 2 (RP2350)	`target/rp2350.cfg`
Pico 2 RISC-V	`target/rp2350.cfg` with `-c "set USE_CORE { rv0 rv1 }"`
Rescue (RP2350)	`target/rp2350.cfg` with `-c "set RESCUE 1"`

Typical Debug Session

# Terminal 1: OpenOCD
openocd -f interface/cmsis-dap.cfg -f target/rp2350.cfg -c "adapter speed 5000"

# Terminal 2: GDB
arm-none-eabi-gdb my_app.elf
(gdb) target remote localhost:3333
(gdb) monitor reset init
(gdb) load
(gdb) break main
(gdb) continue

Flash via SWD

openocd -f interface/cmsis-dap.cfg -f target/rp2350.cfg \
  -c "adapter speed 5000" \
  -c "program my_app.elf verify reset exit"

Use the .elf file for SWD flashing, not .uf2.

Gotchas

These are the most common mistakes and non-obvious behaviours. Pay close attention.

SDK defaults to Pico 1. You must explicitly pass -DPICO_BOARD=pico2 to target RP2350. Forgetting this builds for RP2040 and the binary will not run on a Pico 2.
Use the Raspberry Pi fork of OpenOCD. Upstream OpenOCD (0.12.0) lacks full RP2350 support. Clone from https://github.com/raspberrypi/openocd.git branch rpi-common.
Wrong target config = failed connection. Using rp2040.cfg with a Pico 2 silently fails. Always match the target config to the chip.
SWD uses .elf, BOOTSEL uses .uf2. These are different formats for different flashing methods. Do not try to flash a .uf2 via OpenOCD/SWD.
Debug builds required for meaningful debugging. Always pass -DCMAKE_BUILD_TYPE=Debug to cmake. Release builds optimise away variable state and reorder code, making breakpoints unreliable.
RISC-V mode has no FPU. The hardware floating-point unit is only available on Cortex-M33. RISC-V mode uses software float, which is significantly slower for float-heavy code.
RISC-V requires a clean build directory. When switching between ARM and RISC-V, delete the build directory and re-run cmake. In-place switching does not work.
RISC-V debugging requires pre-selection. The RP2350 boots into Cortex-M33 by default. To debug RISC-V: picotool reboot -u -c riscv, then use OpenOCD with set USE_CORE { rv0 rv1 }.
Debug Probe does not power the target. The Pico 2 must be powered via its own USB or VSYS. The SWD connector carries no power.
LED pin differs on wireless models. Non-wireless Pico 2 uses GP25 for the onboard LED. Pico 2 W uses WL_GPIO0 through the CYW43439 wireless chip. Code must be conditional.
Git submodules are required. The pico-sdk needs git submodule update --init to pull tinyusb, cyw43-driver, lwip, btstack, and mbedtls. Missing submodules cause cryptic build failures.
OTP is irreversible. Writing OTP bits is permanent. Misconfiguring secure boot (setting SECURE_BOOT_ENABLE without a boot key and with PICOBOOT disabled) permanently bricks the device.
Wireless SPI pin sharing. On Pico 2 W, the VSYS ADC reading and CYW43439 IRQ checking are blocked during SPI transactions to the wireless chip.