packets-wire-format

name	packets-wire-format
description	Reticulum's packet structure and wire format. Use when working with packet headers, MTU/MDU, packet types, header types (HEADER_1/HEADER_2), packet context flags, IFAC, or binary packet encoding.

Packets & Wire Format

This skill provides detailed technical knowledge about Reticulum's binary packet structure and wire format, essential for understanding how data flows across the network at the byte level.

Binary Packet Structure

Every Reticulum packet follows a strict binary format:

[HEADER 2 bytes] [IFAC 0-64 bytes] [ADDRESSES 16/32 bytes] [CONTEXT 1 byte] [DATA 0-464 bytes]

Field Details

HEADER (2 bytes)

• Byte 1: Packed flags (see Header Byte 1 structure below)
• Byte 2: Hop count (0-255)

IFAC Field (0-64 bytes, optional)

• Only present if IFAC flag is set in header
• Length varies by interface configuration (1-64 bytes)
• Used for interface authentication/access control
• Public interfaces don't use IFAC (length = 0)

ADDRESSES Field (16 or 32 bytes)

• HEADER_1: Single 16-byte destination hash
• HEADER_2: Two 16-byte hashes (transport_id + destination_hash)
• Addresses are SHA-256 hashes truncated to 128 bits (16 bytes)

CONTEXT Field (1 byte)

• Indicates packet context/purpose
• See Context Types section below

DATA Field (0-464 bytes)

• Payload data (encrypted or plaintext depending on packet type)
• Maximum size depends on MTU/MDU calculations

Header Byte 1 Structure

The first header byte encodes six pieces of information using bit fields:

Bit Layout: [IFAC][Header Type][Context Flag][Propagation][Dest Type 2 bits][Packet Type 2 bits]

Bit 7:     IFAC Flag (1 bit)
Bit 6:     Header Type (1 bit)
Bit 5:     Context Flag (1 bit)
Bit 4:     Propagation Type (1 bit)
Bits 3-2:  Destination Type (2 bits)
Bits 1-0:  Packet Type (2 bits)

Extracting Header Fields

From a raw packet's first byte:

flags = raw_packet[0]

ifac_flag        = (flags & 0b10000000) >> 7
header_type      = (flags & 0b01000000) >> 6
context_flag     = (flags & 0b00100000) >> 5
propagation_type = (flags & 0b00010000) >> 4
destination_type = (flags & 0b00001100) >> 2
packet_type      = (flags & 0b00000011)

Packing Header Fields

When constructing a packet:

packed_flags = (
    (header_type << 6) |
    (context_flag << 5) |
    (transport_type << 4) |
    (destination_type << 2) |
    packet_type
)

Note: IFAC flag is typically set by the interface layer, not in application code.

Packet Types

Four fundamental packet types (2 bits, values 0-3):

Type	Value	Purpose	Encrypted
DATA	0x00	Application data	Usually yes
ANNOUNCE	0x01	Identity/service announcement	No
LINKREQUEST	0x02	Establish link	No
PROOF	0x03	Delivery confirmation	Depends on context

Packet Type Usage

DATA (0x00)

• Standard application payload delivery
• Encrypted to SINGLE/GROUP destinations
• Can be sent over links (using link encryption)
• Context field indicates specific data purpose

ANNOUNCE (0x01)

• Broadcasts identity and public key
• Contains signed identity proof
• Never encrypted (must be readable by all)
• Propagates through network based on hop count
• Used for path discovery

LINKREQUEST (0x02)

• Initiates link establishment with a destination
• Contains ephemeral key for link encryption
• Not encrypted (but contains cryptographic material)
• Requires PROOF response to complete handshake

PROOF (0x03)

• Confirms successful packet delivery
• Can be explicit (with packet hash) or implicit
• Link proofs are encrypted; resource proofs are not
• Size: ~115 bytes for explicit proofs

Header Types

Two header formats control address field structure:

HEADER_1 (0x00)

• Two byte header + one 16-byte address field
• Total header size: 2 bytes + 16 bytes = 18 bytes (+ 1 context = 19)
• Used for:
  • Broadcast packets
  • Direct destination communication
  • Most application-level packets

HEADER_2 (0x01)

• Two byte header + two 16-byte address fields
• Total header size: 2 bytes + 32 bytes = 34 bytes (+ 1 context = 35)
• Used for:
  • Packets in transport (being forwarded)
  • First address: transport_id (next hop)
  • Second address: destination_hash (final destination)

Destination Types

Four destination types (2 bits):

Type	Value	Bits	Purpose
SINGLE	0	00	One-to-one, ephemeral encryption
GROUP	1	01	One-to-many, shared key
PLAIN	2	10	Unencrypted broadcast
LINK	3	11	Over established link

Propagation Types

Two propagation modes (1 bit):

BROADCAST (0)

• Packet travels on local interfaces only
• Not forwarded by transport nodes
• Hop count typically low (0-3)

TRANSPORT (1)

• Packet can be forwarded across multiple hops
• Routed through transport nodes
• Uses path tables for routing
• Header may be rewritten to HEADER_2 for forwarding

Context Types

The context byte indicates packet purpose within higher-level protocols:

Core Context Values

NONE           = 0x00  # Generic data packet
RESOURCE       = 0x01  # Resource transfer data chunk
RESOURCE_ADV   = 0x02  # Resource advertisement
RESOURCE_REQ   = 0x03  # Resource part request
RESOURCE_HMU   = 0x04  # Resource hashmap update
RESOURCE_PRF   = 0x05  # Resource proof (not encrypted)
RESOURCE_ICL   = 0x06  # Resource initiator cancel
RESOURCE_RCL   = 0x07  # Resource receiver cancel
CACHE_REQUEST  = 0x08  # Path/announce cache request
REQUEST        = 0x09  # Request packet (request/response pattern)
RESPONSE       = 0x0A  # Response to request
PATH_RESPONSE  = 0x0B  # Path request response
COMMAND        = 0x0C  # Command packet
COMMAND_STATUS = 0x0D  # Command execution status
CHANNEL        = 0x0E  # Link channel data

Link-Specific Context Values

KEEPALIVE      = 0xFA  # Link keepalive (no data)
LINKIDENTIFY   = 0xFB  # Link peer identification proof
LINKCLOSE      = 0xFC  # Link close notification
LINKPROOF      = 0xFD  # Link packet proof
LRRTT          = 0xFE  # Link request RTT measurement
LRPROOF        = 0xFF  # Link request proof

Context Flag

The context flag (bit 5 in header byte 1) provides additional signaling:

• FLAG_UNSET (0): Standard behavior
• FLAG_SET (1): Context-dependent signaling

Usage varies by packet context. For example, in resource transfers it may indicate last packet, or in links it may signal specific protocol states.

MTU, MDU, and Size Calculations

Understanding packet size limits is critical for protocol implementation:

Constants

MTU = 500               # Maximum Transmission Unit (bytes)
TRUNCATED_HASHLENGTH = 128  # Hash length in bits (16 bytes)
HEADER_MAXSIZE = 2 + 1 + (128//8)*2  # 35 bytes
IFAC_MIN_SIZE = 1       # Minimum IFAC overhead

MDU (Maximum Data Unit)

The maximum payload size in a packet:

MDU = MTU - HEADER_MAXSIZE - IFAC_MIN_SIZE
    = 500 - 35 - 1
    = 464 bytes

The MDU is 464 bytes as calculated above.

ENCRYPTED_MDU

When encryption is applied, overhead reduces available payload:

TOKEN_OVERHEAD = 48    # IV (16 bytes) + HMAC (32 bytes)
KEYSIZE = 512          # Identity keypair size in bits (64 bytes = KEYSIZE//8)
AES128_BLOCKSIZE = 16  # AES block size

# The calculation from Packet.py (KEYSIZE//16 = 32 bytes for ephemeral public key):
ENCRYPTED_MDU = floor((MDU - TOKEN_OVERHEAD - KEYSIZE//16) / AES128_BLOCKSIZE) * AES128_BLOCKSIZE - 1
              = floor((464 - 48 - 32) / 16) * 16 - 1
              = floor(384 / 16) * 16 - 1
              = 24 * 16 - 1
              = 384 - 1
              = 383 bytes

The ENCRYPTED_MDU is 383 bytes. The KEYSIZE//16 term (32 bytes) accounts for the ephemeral X25519 public key prepended to encrypted tokens.

Practical Size Limits

Packet Type	Typical Size	Max Size
Path Request	51 bytes	-
Announce	167 bytes	-
Link Request	83 bytes	-
Link Proof	115 bytes	-
Link RTT	99 bytes	-
Link Keepalive	20 bytes	-
Data (encrypted to SINGLE)	Variable	383 bytes payload
Data (unencrypted/GROUP)	Variable	464 bytes payload
Data (over Link)	Variable	~431 bytes payload

IFAC (Interface Access Code)

IFAC provides interface-level authentication and access control:

Purpose

• Restricts access to specific interfaces
• Prevents unauthorized nodes from using sensitive interfaces
• Adds 0-64 bytes to packet size
• Validated before packet processing

IFAC Flag

Bit 7 of header byte 1:

• 0: Public interface, no IFAC
• 1: IFAC included after header, before addresses

IFAC Structure

When present, IFAC appears immediately after the 2-byte header:

[Header Byte 1][Header Byte 2][IFAC N bytes][Addresses...][Context][Data]

The IFAC content is interface-specific and opaque to higher protocol layers. Length is negotiated during interface configuration.

IFAC in Packet Parsing

When unpacking a packet with IFAC set:

1. Read 2-byte header
2. Determine IFAC length (interface-specific)
3. Extract and validate IFAC
4. Parse remaining fields starting after IFAC

Most application code doesn't handle IFAC directly—it's managed by the interface layer.

Packet Construction Example

Building a simple DATA packet to a SINGLE destination (broadcast):

import struct

# Parameters
destination_hash = b'\x01\x02\x03...'  # 16 bytes
data_payload = b"Hello, Reticulum!"
hops = 0

# Header byte 1
header_type = 0      # HEADER_1
context_flag = 0     # FLAG_UNSET
transport_type = 0   # BROADCAST
destination_type = 0 # SINGLE
packet_type = 0      # DATA

flags = (
    (header_type << 6) |
    (context_flag << 5) |
    (transport_type << 4) |
    (destination_type << 2) |
    packet_type
)  # Result: 0b00000000 = 0x00

# Pack header
header = struct.pack("!B", flags)      # Byte 1: 0x00
header += struct.pack("!B", hops)      # Byte 2: 0x00

# Add destination
header += destination_hash             # 16 bytes

# Add context
context = 0x00  # NONE
header += struct.pack("!B", context)   # 1 byte

# Encrypt data (simplified, actual encryption is complex)
ciphertext = encrypt_for_destination(data_payload, destination_hash)

# Assemble packet
raw_packet = header + ciphertext

# Verify size
if len(raw_packet) > 500:
    raise ValueError("Packet exceeds MTU")

Packet Parsing Example

Unpacking a received packet:

# Assume raw_packet is received bytes
flags = raw_packet[0]
hops = raw_packet[1]

# Extract header fields
ifac_flag = (flags & 0b10000000) >> 7
header_type = (flags & 0b01000000) >> 6
context_flag = (flags & 0b00100000) >> 5
transport_type = (flags & 0b00010000) >> 4
destination_type = (flags & 0b00001100) >> 2
packet_type = (flags & 0b00000011)

# Determine hash length
DST_LEN = 16  # TRUNCATED_HASHLENGTH // 8

# Parse based on header type
if header_type == 1:  # HEADER_2
    transport_id = raw_packet[2:DST_LEN+2]
    destination_hash = raw_packet[DST_LEN+2:2*DST_LEN+2]
    context = raw_packet[2*DST_LEN+2]
    data = raw_packet[2*DST_LEN+3:]
else:  # HEADER_1
    transport_id = None
    destination_hash = raw_packet[2:DST_LEN+2]
    context = raw_packet[DST_LEN+2]
    data = raw_packet[DST_LEN+3:]

# Process based on packet type
if packet_type == 0:  # DATA
    if destination_type == 0:  # SINGLE
        plaintext = decrypt_data(data, destination_hash)
    # ... handle data
elif packet_type == 1:  # ANNOUNCE
    # ... process announce

Wire Format Diagram Examples

Example 1: Broadcast DATA Packet (HEADER_1)

   HEADER FIELD   DESTINATION FIELD   CONTEXT FIELD  DATA FIELD
 _______|_______   _______|_______   ________|______   __|_
|               | |               | |               | |    |
00000000 00000111 [HASH1, 16 bytes] [CONTEXT, 1 byte] [DATA]
|| | | |    |
|| | | |    +-- Hops             = 7
|| | | +------- Packet Type      = DATA (00)
|| | +--------- Destination Type = SINGLE (00)
|| +----------- Propagation Type = BROADCAST (0)
|+------------- Header Type      = HEADER_1 (0)
+-------------- Access Codes     = DISABLED (0)

Example 2: Transport DATA Packet (HEADER_2)

   HEADER FIELD           DESTINATION FIELDS            CONTEXT FIELD  DATA FIELD
 _______|_______   ________________|________________   ________|______   __|_
|               | |                                 | |               | |    |